GeoVision GV-AS1520 Manuel utilisateur
Thank you for purchasing GV-AS1520 Controller. This guide is designed to assist the new user
in getting immediate results from the controllers. For advanced information on how to use
GV-AS1520, please refer to GV-AS1520 Controller User's Manual.
Quick Start Guide
GV-AS1520 Controller
AS1520V206-QG-A
© 2020 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the written
consent of GeoVision.
Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc.
makes no expressed or implied warranty of any kind and assumes no responsibility for errors or
omissions. No liability is assumed for incidental or consequential damages arising from the use of the
information or products contained herein. Features and specifications are subject to change without
notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are
trademarks of GeoVision, Inc. Windows is the registered trademarks of Microsoft Corporation.
July 2020
i
Contents
1. Introduction....................................................................................................................1
1.1 Packing List .............................................................................................................................1
1.2 Wire Definitions .......................................................................................................................1
1.3 LED Status and Beeper...........................................................................................................2
2. Wiring.............................................................................................................................3
3. Installation......................................................................................................................6
3.1 Installing GV-AS1520 ..............................................................................................................6
3.2 Installation Considerations ......................................................................................................7
4. Installing on a Network................................................................................................12
4.1 Checking the Dynamic IP address ........................................................................................13
4.2 Configuring the Static IPAddress..........................................................................................14
4.3 Configuring DDNS Connection..............................................................................................15
1
1. Introduction
Welcome to the GV-AS1520 Quick Start Guide. In the following sections, you will learn the installation
basics for setting up a GV-AS1520. For the detailed instructions of use, see GV-AS1520 Controller
User's Manual.
The latest firmware together with all required software and documentation of GV-AS1520 can found
from GeoVision website.
1.1 Packing List
1. GV-AS1520
2. L-Bracket
3. Fixed-Clamp
4. U-Clip
5. Screw x 4
6. Quick Guide
7. Warranty Card
1.2 Wire Definitions
Wire Definition Wire Definition
Red 12V DC Light Red DO NO2 (Alarm)
Black GND Yellow DO NO3 (Green LED)
Blue RS-485+ White DO NO4 (Red LED)
Light Blue RS-485– Orange IN COM
Brown DO COM Gray IN1 (Sensor)
Green DO NO1 (Gate) Purple IN2 (Not Functional)
2
1.3 LED Status and Beeper
You can find the LED at the bottom of your GV-AS1520.
Condition LED Beeper
Boot completed Green Two long beeps
Ready Green N/A
The e-tag is detected but
the access is denied. Displays red LED
momentarily Three short beeps
3
2. Wiring
Use either a Power over Ethernet (POE) adapter or a power adapter to provide power to the
GV-AS1520.
IMPORTANT: GV-AS1520 can only accept PoE power supply or the DC power adapter as one power
source. Connecting two power sources at the same time will cause damage to the unit.
Note:
1. The total power consumption must be under 25 W when using a POE adapter.
2. The barrier open signal in DO_NO1 only supports DC current.
4
Wiring
5
2
1. RS-485 Card Readers
1.1 Connect with up to 2 readers through a single RS-485 cable.
1.2 When connecting a second reader, a separate power source is required to power the
second reader.
2. Input Device
2.1 The input is dry contact.
2.2 The input can be configured as normally open (NO) or normally closed (NC) through the
Web interface.
3. Output Devices
3.1 Each relay output (DO_NO1 ~ 4) can only support a maximum power consumption of 30V
DC, 500mA.
4. Connecting the PC
4.1 Use TCP/IP to connect GV-AS1520 to a computer that allows you to access its Web
interface and GV-ASManager if the computer is installed with GV-ASManager.
5. Connecting the Power
5.1 When using a Power Adapter connect the 12V DC and GND wires to a 12V DC power
adapter and then connect the power adapter to a power source.
5.2 When using PoE adapter, power will be provided to the device through the Ethernet cable.
6
3. Installation
3.1 Installing GV-AS1520
You can install the reader on a pole or a pillar. Two types of pole mounts are recommended, as
indicated below.
Note: Make sure the diameter of the pole is within 53 mm (0.17 ft).
1. Secure the L-bracket with four screws (supplied) on the rear side of the UHF RFID Reader.
2. Secure the reader on a pillar or a pole using fixed-clamp and U-clip.
Installation
7
3
3. Adjust the angle of the U-clip on L-bracket and secure the hexagon screw nuts.
4. Here is an overview of the pole mount.
3.2 Installation Considerations
The reading range of 10 m (33 ft) is achieved when the RFID Reader and the RFID tag are installed at
the same height, facing each other. The reading range is heavily dependent on the readability of the
RFID tags being recognized. Therefore, the reading range may be affected by a variety of
environmental and situational factors, which are exemplified by but no limited to the list below:
The view angle and height of the RFID Reader installed, relative to:
- The position of the RFID Tag being recognized
- The position and curve of angle, if any, of the driving lane
The stability of the power supply of the RFID Reader
The quality and conditions of the RFID Tag being recognized
Whether there is any obstruction, especially metal or other materials such as insulation film on
the front windshield, between the RFID Reader and Tag
Whether there is any electromagnetic interference near the installation site of the RFID Reader
Whether there is any channel-interference among multiple RFID Readers installed close to
each other
Autres manuels pour GV-AS1520
2
Table des matières
Autres manuels GeoVision Contrôleurs
GeoVision
GeoVision GV-AS100 Manuel utilisateur
GeoVision
GeoVision GV-CS1320 Manuel utilisateur
GeoVision
GeoVision GV-AS1010 Manuel utilisateur
GeoVision
GeoVision GV-AS100 Manuel utilisateur
GeoVision
GeoVision GV-AS Series Manuel utilisateur
GeoVision
GeoVision GV-AS200 Manuel utilisateur
GeoVision
GeoVision GV-AS200 Manuel utilisateur
GeoVision
GeoVision GV-AS1520 Manuel utilisateur
GeoVision
GeoVision GV-AS210 Manuel utilisateur
GeoVision
GeoVision GV-AS100 Manuel
