Genexis Pulse Manuel utilisateur
Pulse
WiFi Repeater/Extender
Full Installation Guide
Revision 1.0. - August 2018
Copyright © 2018 Genexis B.V. All rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document.
Genexis reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
Contents
Models Supported ...........................................................................................................................................................3
Box Content .....................................................................................................................................................................4
Button Overview...............................................................................................................................................................6
Port Overview...................................................................................................................................................................8
Installation ........................................................................................................................................................................9
WPS Pairing ....................................................................................................................................................................11
Manual Pairing................................................................................................................................................................12
LED Status ......................................................................................................................................................................14
Troubleshooting .............................................................................................................................................................16
Advanced Conguration ................................................................................................................................................17
Safety and Care ..............................................................................................................................................................19
Notes..............................................................................................................................................................................20
3
Model Port overview
Pulse
Models Supported
On the label at the bottom of your Pulse (as shown on page 5) you can look up your Pulse model.
In the table below, you see a full overview of all the models.
4
Power adapter
A power adapter is included. This will be used to power your Pulse.
Box Content
Power adapterPulse
Pulse
The main product in your package is your Pulse.
SSID: Genexis-xxxx
WiFi-Key:
**************
WARNING: POWER RATING:12V2A
GUI: http://Genexis-xxxx
Username: user
Password: user
Made in China
Model: Pulse
P/N: 99618025
Version: 1.0
Date: 2018-05
WARNING: POWERRATING:12V2A
Do notuse any other poweradapter
exceptthe one that accompanies this unit.
Use of otheradapter could resultin damage
to theunit. To prevent electronicsshock,
pleasedo not open the cover.
Designed in Sweden Made in China
Model: Pulse
P/N: 99618025
Version: 1.0
Date: 2018-05
S/N: XXXXXXXXXXXXXXXX
MAC: 00:22:07:XX:XX:XX
SSID: Genexis-xxxx
WiFi-Key:
**************
Pulse
WiFi Repeater/Extender
Quick Installation Guide
Manual pairing
Connect to your Pulse WiFi
Consult the information label at the bottom
of your Pulse. It shows the SSID of the WiFi
network (i.e. Genexis-xxxx). Connect to this
WiFi network with your computer.
Login to your Pulse settings page
Open a web browser on your computer and
login to the following page by replacing the
fi eld “xxxx” in http://Genexis-xxxx/ with your
SSID. Use the following login credentials:
Username: user
Password: user
Confi gure network settings
You will now be presented with the screen
above. From that screen, select your home
network and fi ll in the login credentials of
your home network.
After approximately 2 minutes the internet
LED turns yellow.
You have now connected your Pulse to your
home network. Your connection to the web
interface will be interrupted.
To continue using internet on your computer,
connect to your home network again.
5. Connect Pulse to your router
To get the best performance of your Pulse,
connect an Ethernet cable to the WAN port
of your Pulse and to one of the LAN ports of
your router.
For more information about your Pulse, have
a look at the Full Installation Guide
(https://genexis.eu/download-portal/#pulse)
or contact your service provider.
www.genexis.eu
Revision 1.5. - August 2018
Copyright © 2018 Genexis B.V. All rights reserved.
From now on the web interface for your
Pulse can only be reached by obtaining the
new IP address of your Pulse via the web
interface of your router.
Consult the advanced confi guration section
of the Full Installation Guide on how to
retrieve this IP address.
5
Information label
The information on this label is needed when con guring your Pulse.
On the label you can nd information on how to access the web
interface and what the login credentials are.
There are two labels included in the box. These are copies of the label
on the bottom of your Pulse.
It is important you keep one label somewhere safe as it contains
information essential to con gure your device. You can place your
spare label on page 20.
The second label may be retained by the device installer.
Information label
Quick Installation Guide
A Quick Installation Guide is included this is used to install your Pulse.
The Quick Installation Guide gives a step by step overview of the steps
you should take to install your Pulse.
Quick Installation Guide
Reset button Power switch
2.4GHz
5GHz
Internet
Status
WPS
2.4GHz touch button
5GHz touch button
WPS touch button
6
Button Overview
2.4GHz touch button*
The 2.4GHz touch button is located on top of the Pulse.
It enables you to turn the 2.4GHz functionality from the Pulse on or off.
5GHz touch button*
The 5GHz touch button is located on the top of the Pulse.
It enables you to turn the 5GHz functionality from the Pulse on or off.
WPS touch button
The WPS touch button is located on the top of your Pulse.
It enables easy pairing with your router or other home devices.
*By default, this touch button is disabled. This touch button can be
enabled via the GUI.
Power switch
The power switch is located on the side of your Pulse.
It enables you to turn your Pulse on or off.
Reset button
The reset button is located on the side of your Pulse.
This button enables you to perform a factory reset of your Pulse.
You can press this button with a small pin or paperclip.
7
Button Function
Power Flip the switch to turn your Pulse on or off.
Reset Press and hold for 5 seconds to perform a factory reset the device.
2.4GHz Touch the touch button to turn on or off. *
5GHz Touch the touch button to turn on or off. *
WPS Touch and hold the touch button until LEDs start blinking to initiate WPS pairing.
USB 2.0 port
8
Front
Side
Port Overview
Power switch
Reset button
LAN ports
Power connector
Router range
Pulse placement
Pulse range
9
Installation
For the best performance, it’s recommended to place the Pulse ‘free’
from obstacles or objects.
If desired, it is possible to mount your Pulse on a wall using the wall
mount points on the back of the device.
The Drilling Template can be downloaded from the Genexis website at:
https://genexis.eu/download-portal/#pulse
The Pulse can be used in two different setups: either you can connect
via an Ethernet cable or via a wireless connection to your router.
A connection via Ethernet cable gives the best performance.
1. Placement
In the house illustration above, the router range indicates the range of
your own router.
For optimal performance of your Pulse, it is advised to place your Pulse
in the Pulse placement area. Make sure placement is within range of
your router while providing the most coverage to your house.
The Pulse can be placed on a desk or mounted on a wall.
10
Installation
2. Connect to the power
Connect the supplied power adapter to your Pulse and plug the
adapter into an AC power socket.
3. Turn on your Pulse
Turn on your Pulse by ipping the switch on the side of the device.
After approximately 1.5 minutes the Status LED should turn green and
stop blinking. Your Pulse is now ready for use.
4. Synchronize with your network
Synchronizing with your wireless home network can be done using two
different methods:
• Automatically via WPS pairing
• Manually via your web browser
Autres manuels pour Pulse
1
Table des matières
Autres manuels Genexis Répétiteur
