General Hobby Wilga 100cc Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels General Hobby Jouet

General Hobby

General Hobby Wilga 30cc Manuel utilisateur

General Hobby

General Hobby Baron 15cc Series Manuel utilisateur

General Hobby

General Hobby Ultimate Manuel utilisateur

General Hobby

General Hobby CITABRIA-120 Manuel utilisateur

General Hobby

General Hobby Piper J3 Manuel utilisateur

General Hobby

General Hobby F-16 fighting falcon Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur

Wilga 100 & 50cc

Assembly Manual

Caution!

You should not regard this plane as a toy!

To ensure safety, please read this instruction manual thoroughly before

assembly.

Building and operating a model plane requires diligent practice and correct

guidance. An inexperienced flyer can cause serious injury and property

damage.

Seek the assistance of an experienced RC pilot or model airplane club for

help with assembly, operation and maintenance to ensure your flying

experience is both enjoyable and safe.

Fly only in AMA (Academy of Model Aeronautics) approved areas.

Approved areas or areas approved by the Model Association of your

country.

Note: the accessories coming with airplane may not same as below list. Please inquire it with the distributor.

Main Landing Gear Installation

Gather the main landing gear, gear cover, and the wheels

Take off the braces and insert the landing gear into the gear cover

Note: Most airplane do Not have these brace. We donot attach these

braces, because it is only for scale, no other use.

Fix on the wheels

Install the landing gear into the fuselage by screws as shown.

Stick the gear cover onto the fuselage by tapes.

The distance to the upper screw (gear cover screw) is 130mm.

The distance of the two screws is 14mm.

This is the information for your to drill the holes (3mm) for the gear

cover screws. And also the information for the gear braces hole

that you need to drill on the gear cover.

Use 3mm taps to lock the landing gear cover

Drill another two holes on the fuselage for the gear braces.

The gear braces is for scale look. So you just need to insert the gear

braces into the fuselage

LED light

Find out the LED light system.

Insert the LED light into the holder as shown.

Find out the holes for the LED light in the wings and rudder.

The voltage for the light is 6V.

Find out the hole for the LED light on the top of the rudder and cut it out.

Insert the LED light wire from the top of rudder, and glue it onto the rudder.

Rudder and tail wheel Installation

Find out the steel as shown, insert it into the rudder and glue it.

Connect the rudder onto the fuselage by two pcs of carbon fiber tubes.

Connect it as shown, totally four pcs of wires.

Always do the wire insert the metal tube twice and scrimp the tube.

Insert the steel into the arm, and use screw to lock the steel with the arms.

Findout the parts bag for the tail landing gear

Assembly it as shown

Install the tail landing gear into the fuselage tail with screws

Connect one side of the wire with the rudder and tail servo in the fuselage.

And another side to the arm to steel the tail wheel as shown.

Stabs and Elevator Installation

Servo for elevator is hidden way to install.

Install the control horn on the elevators, connect the servo to the control

horn by push rod and ball-links.

There are many holes on the stabs to make you easy to take off and lock

the stabs with many times.

Cut out the holes to lock the stabs.