GEIGER SOLIDline SoftPlus-Qi GU45-E09 Series Manuel utilisateur

www.geiger.de EN

DE Original-Montage- und

Betriebsanleitung

Original assembly and

operating instructions

Notice originale de montage

et d’utilisation

Instrucciones originales de

instalación y funcionamiento

Istruzioni originali di installazione

e funzionamento

Tubular motor:

GEIGER SOLIDline

Motor control:

SOLIDline SoftPlus-Qi (GU45...-E09)

for cassette awnings and folding arm awnings

2Gerhard Geiger GmbH & Co. KG | 100W1512 0120V001en

Index

1. General information..................................................................2

2. Guarantee ..................................................................................2

3. Intended use..............................................................................3

4. Safety instructions....................................................................3

5. Safety instructions for assembly ............................................4

6. Installation instructions ...........................................................5

7. Information for the specialist electrician................................6

8. Setting of the end positions.....................................................7

9. Obstacle detection....................................................................8

10. End position correction............................................................8

11. What to do if…...........................................................................8

12. Maintenance ..............................................................................8

13. Declaration of conformity ........................................................9

14. Technical data .........................................................................10

15. Notes on waste disposal ........................................................10

1. General information

Dear customer,

By purchasing a GEIGER motor you have decided on a quality product from GEIGER.

Thank you very much for your decision and the condence placed in us.

Before you put this drive into operation please observe the following safety instructions. It

serves for the prevention of danger and for the avoidance of personal injury and damage to

property.

The installation and operating instructions contain important information for the installer, the

specialist electrician and the user. Please pass on these instructions if you transfer the product.

These instructions should be kept by the user.

2. Guarantee

In the case of incorrect installation contrary to the installation and operating instructions and/

or constructional modication, the legal and contractual guarantee for property damage and

product liability lapses.

www.geiger.de EN

3. Intended use

The tubular motors of the model range SOLIDline (GU45...-E09) with electronic limit stop are

designed exclusively for the operation of cassette awnings and folding arm awnings.

The motors may not be used for the operation of roller grilles, garage doors, furniture and lifting

tools.

GU 45 .. . - E09

Motor control

Motor head

Torque in Nm

Motor diameter

GEIGER universal drive

4. Safety instructions

I ATTENTION: Important safety instructions. For personal safety,

it is important to follow these instructions. Please keep these

instructions for future reference.

fDo not allow children to play with stationary controls. Keep remote controls away

from children.

fThe installation is to be checked regularly for defective balance, signs of wear or

damaged cables and springs, if relevant.

fDo observe the moving sun protection system and keep persons away until it has

closed completely.

fWhen operating the manual release with the sun protection system open, please be

cautious as it can fall down quickly if springs or tapes wear off or are broken.

fDo not operate the device if operations such as, for example, window cleaning are to

be carried out in the vicinity.

fDisconnect the automatic controlled device from the mains power supply if opera-

tions such as, for example, window cleaning are being carried out in the vicinity.

fDuring operation observe the danger zone.

fDo not use the installation if people or objects are in the danger zone.

fUrgently shut down damaged installations until repair.

fUnconditionally shut down the unit during maintenance and cleaning operations.

fPinching and shearing points are to be avoided and must be secured.

fThis appliance can be used by children aged 8 and above and persons whose

physical, sensorial or mental capacities are impaired, or who have no experience or

know-how if they have been supervised or been given instructions on the use of the

appliance and if they understand the possible resulting dangers. Children are not

permitted to play with the device. Cleaning and maintenance should not be carried

out by children.

fThe rated sound pressure level is less than 70 dB(A).

fDisconnect the device from the mains power supply for maintenance and replace-

ment of parts.

If the motor is disconnected via a plug connection the operator must be able to

control - from any place to which it has access – that the plug is removed.

If this is not possible - due to design or installation - the disconnection from the

power supply must be ensured via locking in the disconnected position (e.g. isolator).

fThe motor tube can get very hot during prolonged use.

When working on the unit, do not touch the tube before it has cooled down.

4Gerhard Geiger GmbH & Co. KG | 100W1512 0120V001en

5. Safety instructions for assembly

I ATTENTION: Important safety instructions. Follow all installation

instructions, as incorrect installation can lead to serious injuries.

fWhen mounting the motor without any mechanical protection of the driven parts and

of the tube which may become hot, the motor must be installed at a height of at least

2.5 m above the ground or of another level which provides access to the drive.

fBefore the motor is installed, all cables which are not needed are to be removed and

all equipment which is not needed for power-operated actuation is to be put out of

operation.

fThe actuating element of a manual release must be mounted at a height of less than

1.8 m.

fIf the motor is controlled by a switch or pushbutton, the switch or pushbutton must

be mounted within eyeshot of the motor. The switch or pushbutton must not be

located in the vicinity of moving parts. The height of installation must be at least

1.5mabovetheoor.

fPermanently installed control devices must be attached visibly.

fIn case of devices extending horizontally, a horizontal distance of at least 0.4 m must

berespectedbetweenthefullyextendedpartandanyotherxedelement.

fThe rated speed and the rated torque of the motor must be compatible with the

device.

fThe mounting accessories that are used must be designed in accordance with the

selected rated torque.

fGood technical knowledge and good mechanical skills are necessary for the motor

installation. Incorrect installation can lead to serious injury.

Electricalworkmustbecarriedoutbyaqualiedelectricianinaccordancewiththe

regulations in force locally.

fOnly use connecting cables that are suitable with the environmental conditions and

which meet the construction requirements. (see accessories catalogue)

fIf the device is not equipped with a connecting cable and a plug, or other means for

disconnecting from the mains with a contact opening on each pole according to the

conditions of the overvoltage category III for full disconnection, a disconnecting

device of this type must be incorporated into the permanently installed electrical

installation according to the wiring rules.

fDo not mount the connecting cables near hot surfaces.

fA plug for the disconnection of the motor from the power supply must be accessible

after installation.

fDamaged connecting cables must be replaced by GEIGER connecting cables of the

same type.

fThe device must be mounted as described in the installation instructions. Fixations

shall not be made with adhesives since they are regarded as unreliable.

www.geiger.de EN

6. Installation instructions

I Beforexing,thestrengthofthemasonryorofthesubsurfaceistobe

checked.

I Prior to installation please check to ensure there is no visible damage

to the motor like cracks or open cables.

I Caution: If the tube is screwed/riveted to the drive, the measure must

be taken from the tube end to the center of the drive and marked on

the tube.

When drilling the winding shaft never drill into the

area of the tubular motor!

When inserting into the shaft, the tubular motor must not

be struck and must not be allowed to fall into the shaft.

Installation into the awning:

Insert motor with a suitable adapter and drive into the shaft

up to the stop of the shaft adapter.

Fix the motor support on the awning. Fix the motor

together with the shaft on the motor support. The bearer

locks into place.

Depending on the selected motor head, diffe-

rentxationsystemscanbeused:

– Place the motor with square insert in the star-shaped

bearer and lock with pin

– Place the motor into the existing engine bearer and

lock

– Place the motor in a compatible engine bearer with clip

system and lock with spring or rotating lever

I The GEIGER SOLIDline motor is suitable for shaft diameters from

50 mm!

6Gerhard Geiger GmbH & Co. KG | 100W1512 0120V001en

7. Information for the specialist electrician

H Caution: Important installation instructions.

Please follow all installation instructions

since incorrect installation can lead to

the destruction of the motor and the

switching unit.

The operations with the service clamps may be

accomplished only by an electrical specialist.

Motors with electronic limit stops can be connected in

parallel. In this case the maximum load of the switching

unit must not be exceeded.

When changing the running direction the switchover must

be effected through an off-position.

When changing the running direction the switchover time

must be at least 0.5 s.

With a three-phase network, please use the same external

conductor in order to control the UP and DOWN directions.

Connecting cables with plug connectors of the Hirschmann

Company are tested and approved with couplings of the

Hirschmann Company.

12 3

PE N

Electronic /

mechanical

limit stop

blue

brown

black

green/yellow

Mains: 230V / 50Hz

www.geiger.de EN

8. Setting of the end positions

I The motor is in learning mode on delivery. The motor jerks (go, stop,

go)ateachruncommandtoconrmthelearningmodeactivation.

I The distance between the upper and lower end stops must be about

25 cm which corresponds to one tube rotation at least.

Programming the end positions

1. Connect the connecting cable of the motor to the control switch.

2. Move the awning to the required lower end position. Any adjustment can be realized here.

3. Move the awning to the upper position without any interruptions until the motor shuts down.

(torque detection). The programming procedure is then completed and the motor returns to

normal operating mode.

Change the end positions

1. Extend the awning and activate the learning mode. For this purpose retract the awning for

1 second, wait 5 seconds, extend the awning for 1 second, wait 5 seconds, retract the

awning for 1 second, wait 5 seconds, retract again the awning for 1 second and wait

5 seconds.

5 sec1 sec 5 sec1 sec 5 sec1 sec 1 sec

breakUP ––––––breakDOWN break

5 sec

–breakUP UP

5 sec

–break

The motor always starts with a jerk when the learning mode is activated.

2. Move the awning to the new lower end position. Any adjustment can be realized here.

3. Move the awning to the upper end position without interruptions until the motor automati-

cally shuts down. (torque detection). The programming procedure is then completed and the

motor returns to normal operating mode.

Note: the motor can be programmed with any setting cable which allows a simultaneous UP

and DOWN command. The learning mode is activated by pressing simultaneously the UP and

DOWN keys 3 seconds. The motor conrms with 1 x click click.

Connection of the setting cable

Connect the adjusting cable to the connecting cable of the motor. Please always connect

cores of identical colours here. The assignment of the direction keys 1 and 2 to the direction of

rotation depends on the installation situation of the drive. Then connect the adjusting cable to

the 230V mains.

Mains:

230

VSetting cable

M56....

Service

terminals

Connecting cable

to limit stop12

Programming

key

LED

Hirschmann coupling

Adaption cable

M56B265

8Gerhard Geiger GmbH & Co. KG | 100W1512 0120V001en

9. Obstacle detection

When, after the teaching of the rst complete, uninterrupted travel from one end position to the

other end position is carried out, the torque needed is learnt.

In any following complete, uninterrupted travel from end position to end position, the torque

needed is automatically readjusted. Slow changes in the installation due to ageing, soiling, cold

or heat are thus automatically taken into consideration.

This process takes place for both running directions independently of one another. If a travel

movement in up direction is blocked by an obstacle, the motor switches off.

The running direction in which the obstacle was recognized is blocked. The block is removed if

the motor has been operated in the opposite direction for a certain time. An obstacle must thus

rst be released before the motor can be operated again in the direction of the obstacle.

10. End position correction

Should an awning elongation have resulted due to temperature changes, this is corrected at the

next end position correction.

If, due temperature changes, modied winding behaviour should arise and the awning should run

against the stop, an immediate end position correction takes place.

11. What to do if…

Problem Solution

Motor does not run. • Motor not plugged in.

Please check the plug connection.

• Check connecting cable for possible

damage.

• Check the mains voltage and allow the

cause of the voltage breakdown to be

tested by a specialist

electrician.

Instead of in the upwards direction, motor

runs downwards.

• The control leads are interchanged.

Exchange black/brown control leads.

Motor only runs in one

direction.

• Motor in the end position.

Run motor in the opposite direction.

Re-adjust the end positions, if necessary.

After running several times,

the motor breaks down and

no longer responds.

• The motor became too hot and has

switched off.

Try it again after a cooling time of about

15 min.

The motor jerks when starting (runs,

stops, runs).

• The programming mode is activated. The

minimum travel distance has not been fully

respected during programming.

12. Maintenance

The drive is maintenance-free.

www.geiger.de EN

13. Declaration of conformity

Current declarations of conformity are available under www.geiger.de

Schleifmühle 6 |D-74321 Bietigheim-Bissingen

Phone +49 (0) 7142 9380 |Fax +49 (0) 7142 938 230 |[email protected] |www.geiger.de

Sitz Bietigheim-Bissingen |Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146

Komplementär: Geiger Verwaltungs-GmbH |Sitz Bietigheim-Bissingen |Amtsgericht Stuttgart HRB 300481

Geschäftsführer: Roland Kraus |WEEE-Reg.-Nr. DE47902323

Gerhard Geiger GmbH & Co. KG

300H0204

EU Declaration of Conformity

Bietigheim-Bissingen, 25.06.2019 Roland Kraus (General Manager)

Product designation:

Venetian blinds motor, motor for rolling shutters, motor for awnings

Type designation:

GR45.. GJ56..

GS45.. GS56..

GU45.. GSI56..

GB45..

Applied directives:

2006/42/EC

2014/30/EU

2014/53/EU

2011/65/EU + (EU)2015/863 + (EU)2017/2102

Applied standards:

DIN EN 60335-1 (VDE 0700-1):2012-10; EN 60335-1:2012

DIN EN 60335-1 Ber.1 (VDE 0700-1 Ber.1):2014-04; EN 60335-1:2012/AC:2014

EN 60335-1:2012/A11:2014

DIN EN 60335-2-97 (VDE 0700-97):2017-05; EN 60335-2-97:2006+A11:2008+A2:2010

+A12:2015

DIN EN 62233 (VDE 0700-366):2008-11; EN 62233:2008

DIN EN 62233 Ber.1 (VDE 0700-366 Ber.1):2009-04; EN 62233 Ber.1:2008

DIN EN ISO 12100:2011-03; EN ISO 12100:2010

DIN EN 55014-1:2012-05; EN 55014-1:2006 + A1:2009 + A2:2011

DIN EN 55014-2:2016-01; EN55014-2:2015

DIN EN 61000-3-2:2015-03; EN 61000-3-2:2014

DIN EN 61000-3-3:2014-03; EN 61000-3-3:2013

ETSI EN 301 489-1 V1.9.2(2011-09)

ETSI EN 301 489-3 V1.6.1(2013-08)

ETSI EN 300 220-2 V3.1.1(2017-02)

Authorized representative for technical data:

Gerhard Geiger GmbH & Co. KG

Address:

Schleifmühle 6, D-74321 Bietigheim-Bissingen

Gerhard Geiger GmbH & Co. KG

Antriebstechnik

Schleifmühle 6

D-74321 Bietigheim-Bissingen

0619100W1518

10 Gerhard Geiger GmbH & Co. KG | 100W1512 0120V001en

14. Technical data

Technical data of tubular motor SOLIDline-KS (GU45..)

GU4506 GU4510 GU4520 GU4530 GU4540 GU4550

Voltage 230 V~/50 Hz

Current 0,36 A 0,47 A 0,63 A 0,8 A 1,0 A 1,0 A

Cos Phi (cosj)>0,95

Inrush current (factor) x 1,2

Power 83 W 105 W 140 W 180 W 220 W 220 W

Torque 6 Nm 10 Nm 20 Nm 30 Nm 40 Nm 50 Nm

Speed 16 rpm 16 rpm 16 rpm 16 rpm 16 rpm 12 rpm

Protection class IP 44

Total length1) 506,5

516,5

546,5

566,5

586,5

Operating mode S2 4 min S2 4 min S2 5 min S2 4 min S2 4 min S2 4 min

Sound pressure level2) 39 dB(A) 39 dB(A) 41 dB(A) 41 dB(A) 43 dB(A) -

Diameter 45 mm

Weight approx

1,85 kg

approx

1,90 kg

approx

2,20 kg

approx

2,40 kg

approx

2,70 kg

approx

2,70 kg

Storage temperature/

Humidity

T = -15°C .. +70°C / dry and non-condensing place

1) SOLIDline-COM + 3,5 mm / SOLIDline-SOC: + 3 mm / SOLIDline-SIL: ± 0 mm (without trunnion)

2) The average sound pressure level data are intended for guidance only. The values were determined by

GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is no

reference to any specific test standard.

Subject to technical modifications. Please find information to the ambient

temperature range of our GEIGER motors under www.geiger.de DE

geprüfte

Sicherheit

15. Notes on waste disposal

Recycling of packaging materials

In the interest of environmental protection, please contact your local government’s recycling or

solid waste management department to learn more about the services it provides.

Waste disposal of electric and electronic equipment

Electrical and electronic equipment must be collected and disposed of separately in accordance

with EU regulations.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GEIGER Moteur

GEIGER

GEIGER GEIGER-SOLIDline Series Manuel utilisateur

GEIGER

GEIGER GEIGER-SoftZero-55 Manuel utilisateur

GEIGER

GEIGER SOLIDline GU45 Series Manuel utilisateur

GEIGER

GEIGER GR4510 Manuel utilisateur

GEIGER

GEIGER GJ5606-DuoDrive Manuel utilisateur

GEIGER

GEIGER PRO.TECline Spindle GB45 Series Manuel utilisateur

GEIGER

GEIGER SOLIDline GU4506 Manuel utilisateur

GEIGER

GEIGER SOLIDline Manuel utilisateur

GEIGER

GEIGER GEIGER-SOLIDline Manuel utilisateur

GEIGER

GEIGER INline System GSI56 r Series Manuel utilisateur

GEIGER

GEIGER GB45SS Series Manuel utilisateur

GEIGER

GEIGER GJ5606k F03 Manuel utilisateur

GEIGER

GEIGER GEIGER-SOLIDline Series Manuel utilisateur

GEIGER

GEIGER GJ56 E14-1002 Series Manuel utilisateur

GEIGER

GEIGER GJ56 E14-1002 Series Manuel utilisateur

GEIGER

GEIGER GJ56 e Series Manuel utilisateur

GEIGER

GEIGER GEIGER-MODULARline Manuel utilisateur

GEIGER

GEIGER GB45MR Series Manuel utilisateur

GEIGER

GEIGER GEIGER-Solid Line Manuel utilisateur

GEIGER

GEIGER SOLIDline GJ56 Series Manuel d'utilisation

GEIGER

GEIGER GEIGER-MODULARline Manuel utilisateur

GEIGER

GEIGER GJ56E11 Series Manuel utilisateur

GEIGER

GEIGER INline GSI56 e5 Series Manuel utilisateur

GEIGER

GEIGER SOLIDline GU4510 Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur