Geeetech 3D WiFi Manuel utilisateur

Geeetech 3D WiFi Module

—User Manual—

Contents

Terms ..............................................................................................................................................................1

Safety and Compliance...................................................................................................................................3

1. About Geeetech 3D WiFi Module ..........................................................................................................4

1.1 Introduction.......................................................................................................................................4

1.2 Main Features of 3D WiFi Module...................................................................................................5

1.3 Tips for Using 3D WiFi Module.......................................................................................................6

2. Install EasyPrint 3D App ........................................................................................................................7

3. Bind 3D printer to EasyPrint 3D App.....................................................................................................9

4. Wi-Fi Configurations............................................................................................................................12

5. Printing via EasyPrint 3D App..............................................................................................................18

5.1 Control Your 3D Printer with EasyPrint 3D App............................................................................19

5.1.1 Introduction to Print Interface.......................................................................................19

5.1.2 Move.............................................................................................................................20

5.1.3 Temp .............................................................................................................................21

5.1.4 Level .............................................................................................................................22

5.1.5 Filament ........................................................................................................................23

5.1.6 Wi-Fi.............................................................................................................................24

5.1.7 Config ...........................................................................................................................25

5.2 Introduction to Gallery Interface.....................................................................................................26

5.2.1 Printing from 3D printer’s SD Card.....................................................................................26

5.2.2 Printing from 3D WiFi module’s TF Card ...........................................................................30

5.2.3 Printing from Gallery...........................................................................................................31

5. 3 Introduction to Me Interface..........................................................................................................35

6. Firmware Upgrade for 3D WiFi Module ..................................................................................................40

6.1 Firmware Upgrade for Control Board.............................................................................................40

6.2 Firmware Upgrade for 3D WiFi Module ........................................................................................42

7. FAQ...........................................................................................................................................................43

8. Specs.........................................................................................................................................................45

9. Contact us .................................................................................................................................................46

Terms

Please be advised of the following terms (the ―Terms‖) regarding this User Manual (this

―Manual‖):

All information in this Manual is subject to change at any time without notice and is

provided for convenience purposes only. Geeetech reserves the right to modify or revise this

Manual in its sole discretion and at any time. You agree to be bound by any modifications

and/or revisions. Contact the Geeetech Support Team for up-to-date information.

Content Copyright. The design of this Manual and all text, graphics, information,

content, and other material are protected by copyright and other laws. The contents are

suppliers.

―Marks‖) used in this Manual are registered and unregistered trademarks, trade names, and

service marks of Geeetech and its affiliates. Nothing contained in this Manual grants or

should be construed as granting, by implication, estoppel, or otherwise, any license or right to

use any Marks without the written permission of Geeetech. Any unauthorized use of any

information, materials, or Marks may violate copyright laws, trademark laws, laws of privacy

and publicity, and/or other laws and regulations.

DISCLAIMERS. Neither Geeetech nor any of our affiliates warrants the accuracy

orcompleteness of the information, products, or services provided by or through this Manual,

which are provided ―as is‖ and without any express or implied warranties of any kind,

including warranties of merchantability, fitness for a particular purpose, or non-infringement

of intellectual property. To the fullest extent permissible by the applicable law, we hereby

disclaim all liability for product defect or failure or for claims that are due to normal wear,

product misuse or abuse, product modification, improper product selection, noncompliance

with any codes, or misappropriation. To the fullest extent permissible by the applicable law,

we hereby disclaim any and all responsibility, risk, liability, and damages arising out of death

or personal injury resulting from assembly or operation of our products. Geeetech assumes no

responsibility, nor will be liable, for any damages to, or any viruses or malware that may

infect your computer, telecommunication equipment, or other property caused by or arising

from your downloading of any information or materials related to Geeetech products. The

foregoing exclusions do not apply to the extent prohibited by law; please refer to your local

laws for any such prohibitions. We make no warranties to those defined as ―consumers‖ in

the Magnuson-Moss Warranty–Federal Trade Commission Improvement Act.

LIMITATIONS OF LIABILITY. In no event will Geeetech or any of our respective

officers,directors, employees, shareholders, affiliates, agents, successors, or assigns, nor any

party involved in the creation or production of our products, be liable to you or anyone else

for any indirect, special, punitive, incidental, or consequential damages (including, without

limitation, those resulting from lost profits, lost data, or business interruption) arising out of

the use, inability to use, or the results of use of this Manual, whether based on warranty,

contract, tort, or any other legal theory and whether or not advised of the possibility of such

damages. The foregoing limitations of liability do not apply to the extent prohibited by law;

please refer to your local laws for any such prohibitions.

Safety and Compliance

Radio and Television Interference

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.

These limits are designed toprovide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is noguarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

•Consult the dealer or an experienced radio/TV technician for help.

The following booklet compiled by FCC may help you:“How to Identify and Resolve

Radio-TV Interference Problems‖

Changes and modifications not expressly approved by the manufacturer or registrant of

this equipment will void your right to use the equipment in accordance with FCC regulations.

Radio Specifications

Frequency

WLAN RF Frequency

Gange

Protocol

Wireless Types

Wireless Specification

Taoglas，P/N

Within 2.4 GHz Band

2.4 GHz

2.412 - 2.472 GHz

802.11 b/g/n

FX831.07.0100C

2.5 dBi

1. About Geeetech 3D WiFi Module

1.1 Introduction

Geeetech developed 3D WiFi Module, with the only aim of enabling all the 3D printing

hobbyists to control their printer wirelessly. 3D WiFi Module is mainly composed of two

parts: control board and Wi-Fi module. Thumb-size as it is, it is powerful enough to connect

your 3D printer with Geeetech’s cloud server, making it a reality for you to control your

device on EasyPrint 3D App.

3D WiFi Module is ready to use right out of box. You just need to connect your printer

to its USB port and finish simple configurations on EasyPrint 3D App. That’s all. Then you

can start to control your printer wirelessly.

3D WiFi Module is cloud-based.Via EasyPrint 3D App, it is extremely simple and

convenient to direct control over your printer anywhere and anytime. Besides, you would

have access to a large cloud gallery, which covers 9 categories of 3D models for printing.

What’s more exciting is that you could record and share your printing moments on EasyPrint

3D App in seconds.

3D WiFi Module is broadly compatible with many different kinds of 3D printers on the

market. As long as the USB to serial chip of your printer belongs to one of these three ones

(CH340, FT232 and PL2303) and is controlled by G.code instructions, our 3D WiFi Module

can upgrade your machine as Wi-Fi enabled and make it comparable to other prohibitively

expensive Wi-Fi connected 3D printers.

Coded professionally and adopting high-performance chips, 3D WiFi Module could

transmit model files and your commands to your printer in a stable and reliable way.

1.2 Main Features of 3D WiFi Module

As a bridge for data transmission between mobile phone and 3D printer, 3D WiFi

module integrates some instructions, convenient for users directing control over 3D printer

from App. Besides, it is compatible with the feedback info from 3D printer to control the

printer and display the related printing data on App.

In this section, a brief introduction to its main features is made to help get a better

knowledge of how 3D WiFi module works.

a. Config mode: Long press the hole labeled with “set”with a pin about 3s, until the

Wi-Fi indicator light turns dim and flickers quickly. Loosen the pin and 3D Wi-Fi will enter

the config mode. In the config mode, you can finish the Wi-Fi connectivity onApp.

b. When the Wi-Fi indicator light flickers quickly and you do not loosen the pin, the

light will flicker slowly to enter the reset mode. In the reset mode, your phone could not

detect GT_printer hotspot.

c. When the network is not stable, 3D WiFi module will re-connect the hotspot

automatically.

In the following part, a detailed introduction to the App menu will be made.

1.3 Tips for Using 3D WiFi Module

* Make sure 3D WiFi module and 3D printer could communicate smoothly with your

USB cable. If not, please contact with [email protected], we will help you pair the basic

firmware with your USB interface.

* Ensure that M26, M27, M110, M114, M119 commands are valid and of correct format,

so that EasyPrint 3D App could display the printing status normally and operations via App,

such as stopping printing and leveling the building platform, are available.

M26, M27, M110 is related to the display and modification of printing status and

parameters on App, when the printer runs with SD card or TF card. M114 and M119 for

leveling the building platform.

If the format of these commands is not in alignment with what is shown in the following

table, please make the corresponding modification.

*You can use serial debugging tools or Repetier-host to send these commands to your

3D printer to test how your machine responds.

M26

Start printing from a specific byte of a g.code file, which is being printed.

G.code: M26 Snnn. ―nnn‖for the numbers.

M27

Obtain info of printing progress.

G.code: M27; Return: ―SD printing byte nnn/nnn‖

M110

Set the line sequence, for instance, the present line No. is nnn, and the next

line should be nnn+1.

G.code: Nnnn M110

M114

The present coordinates for X/Y/Z/E.

G.code: M114; Return: ―X: nnn Y: nnn Z:nnn E: nnn‖

M119

G.code: M119

Return: eg. ―x_min: H y_min:H z_min:L‖

Or ―x_min:OPEN x_max:TRIGGERED y_min: OPEN y_max: TRIGGERED

z_min:TRIGGERED z_max: OPEN‖

2. Install EasyPrint 3D App

Download the EasyPrint 3D APP and install it by following the instructions.

http://www.geeetech.com/firmware/EasyPrint_3D_Android.apk

You could also download EasyPrint 3D App on Google Play and App Store.

Once finishing installation, enter Me to register and log in.

Note: As the EasyPrint 3D APP is continuously upgraded, some UI and workflow may

be different, please follow the APP.

Here are the login steps.

Step1. Open EasyPrint 3D App. Click the [Log in] button in the [Me] interface to finish

your registration.

Step 2. For beginners, click [Register] to create an account. Enter your own account

information (Note: There is no space in the user name. For foreign users, please choose

―English‖for your server address.)

Step 3. Click [Register Now] and a pop-up interface will appear for you to check your

email.

Autres manuels pour 3D WiFi

Table des matières

Autres manuels Geeetech Carte réseau

Geeetech

Geeetech ESP8266 Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur