GE 15163 Manuel utilisateur

Quick Start Guide

Commonly used tools

- Phillips head screwdriver

- Flat head screwdriver

- Hammer

- Wire cutter/stripper

Supplied hardware

- #10 Screw (3)

- #10 Drywall anchors

MIN. COPPER WIRE

SIZE (AWG)

MAX LOAD

(AMP)

MINIMUM INSULATION

TEMP (°C)

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

14 15 60

12 20 60

10 30 60

8 40 105

USE CORRECT GAUGE WIRE PER LOCAL ELECTRICAL CODE

• RECOMMENDED INSTALLATION BY LICENSED ELECTRICIAN.

• HIGH VOLTAGE (THERE MAY BE MORE THAT ONE SOURCE OF SUPPLY)

DISCONNECT ALL POWER SOURCES BEFORE SERVICING.

• RISK OF ELECTRIC SHOCK – ALL TERMINALS ARE LIVE.

• USE COPPER WIRE ONLY.

• CLOSE THE COVER AFTER SETTING.

• TIGHTEN CONNECTIONS TO 25 LBF-IN.

• USE CORRECT GAUGE WIRE (8-14 AWG) BASED ON LOCAL ELECTRICAL

CODE OF AT LEAST 105C RATING.

• APPROVED FOR OUTDOOR USE.

• WIRE STRIP LENGTH ½”

• GROUNDING: NATIONAL ELECTRICAL CODE REQUIRES THAT GROUNDING

MUST BE CONTINUOUS AND IN PROPER ELECTRICAL CONTACT IN ALL

GROUNDING CONDUCTORS, METALLIC CONDUITS AND GROUNDING

TERMINALS.

WARNING

Knockouts

Each metal box comes with ½” and ¾” knockouts. Follow the pictures below to

remove knockouts.

For ½” knockout, place small blade screw driver as pictured above. Tap lightly to

punch knockout loose.

For ¾” knockout, ﬁrst use screwdriver to punchout ½” knockout then use pliers

to remove outer ring.

Final result of ¾” knockout

Mounting the timer

1. Select the location for the timer and use the three holes provided for

mounting.

Mounting holes

2. Remove module from timer box. Hold the timer box in place and mark the

holes on the mounting surface.

3. If mounting to drywall:

a.) Drill a 3/16” size hole for the drywall anchors at the marked locations

b.) Insert an anchor in each hole then gently tap the open end of anchor with

a hammer until the anchor is almost ﬂush with the wall.

c.) Mount the timer to the anchors using the supplied screws.

4. If mounting to plywood, drill a 3/32” size hole for each screw and mount the

timer to the surface using the supplied screws.

120 VAC Setup: Single 120 VAC Load

Connections:

L- Line Input to Timer Motor

1-Line Input to Switch

X-Neutral Input to Timer Motor

2-Line Output of Switch

2XL

LOAD

Removable

Bridge

Typical for same voltage in LOAD and MOTOR

GROUND

L X1 2

• RECOMMENDED INSTALLATION BY LICENSED ELECTRICIAN.

• HIGH VOLTAGE (THERE MAY BE MORE THAT ONE SOURCE OF SUPPLY)

DISCONNECT ALL POWER SOURCES BEFORE SERVICING.

• RISK OF ELECTRIC SHOCK – ALL TERMINALS ARE LIVE.

• USE COPPER WIRE ONLY.

• CLOSE THE COVER AFTER SETTING.

• TIGHTEN CONNECTIONS TO 25 LBF-IN.

• USE CORRECT GAUGE WIRE (8-14 AWG) BASED ON LOCAL ELECTRICAL

CODE OF AT LEAST 105C RATING.

• APPROVED FOR OUTDOOR USE.

• WIRE STRIP LENGTH ½”

• GROUNDING: NATIONAL ELECTRICAL CODE REQUIRES THAT GROUNDING

MUST BE CONTINUOUS AND IN PROPER ELECTRICAL CONTACT IN ALL

GROUNDING CONDUCTORS, METALLIC CONDUITS AND GROUNDING

TERMINALS.

WARNING

Step 1: Remove Plastic Guard

Remove screws using a Phillips Head

screwdriver and keep them to the side.

Carefully remove plastic guard and

also keep to the side.

Step 2: Connect the Input/Clock Motor Voltage

1. Connect 120VAC Hot

(Black) to Terminal L.

Do not remove the

jumper connecting

Terminals “L” and “1”.

2. Connect 120VAC

Neutral (White) to

terminal X.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25lbf-in.

Improper tightening can cause heating and equipment failure.

Step 3: Complete the circuit to the load

1. Connect 120VAC Hot

(Black) of the LOAD to

Terminal 2.

2. Connect 120VAC

Neutral of the Load

(White) to terminal X.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25in-lb.

Improper tightening

can cause heating and

equipment failure.

Step 4: Reinstall the Plastic Guard

Install both screws with the plastic

guard facing the original position.

Removable Bridge

Step 5: Activate Timer

1. Turn the mechanism dial counter

clockwise to set the current time as

accurately as possible.

2. After wiring and setting the timer

with the ON/OFF trippers in the

correct timer positions. Be sure to

depress the ON or OFF lever to set

the timer to the desired state. The

timer will turn ON or OFF at the next

programmed time.

3. You cannot see the dial turning.

Wait at least 30 minutes after the

set ON or OFF time to verify the

timer is operating properly.

Step 6: Check timer after 24 hours

1. After 24 hours, remove power from the timer and check the connections:

a.) Remove plastic guard

b.) Verify all screws and connections are still ﬁrmly tightened.

c.) It is possible that after your initial tightening, the wire has compressed and

loosened the connections.

2. After making sure everything is still tight, replace the plastic guard and

restore power to the timer.

*Please review “Operating Instructions” in the user manual.

Special note for plastic guard

on the back of the motor

On the back of the motor, there is a

plastic guard for “Input” side

connections. It snaps easily in and out

of place. If the guard has come off

during shipment or installation,

reinstall by placing the two tabs at the

bottom in the appropriate slots.

Plastic guard ﬁtted correctly

Pictured is plastic guard

Ends ﬁt into these holes

15163 VERSION 2

01/13/16

WWW.JASCOPRODUCTS.COM

Table des matières

Autres manuels GE Minuteur

GE SunSmart 15042 Manuel utilisateur

GE Indoor SunSmart Manuel utilisateur

GE 15266 Manuel utilisateur

GE SunSmart 15312 Manuel utilisateur

GE Indoor SunSmart Manuel utilisateur

GE SunSmart 15042 Manuel utilisateur

GE my touchsmart 26892 Manuel utilisateur

GE SunSmart 15079 Manuel utilisateur

GE 15147 Manuel utilisateur

GE Digital Timer Manuel utilisateur

GE 15270 Manuel utilisateur

GE Indoor SunSmart Manuel utilisateur

GE SunSmart 15042 Manuel utilisateur

GE 15057 Manuel utilisateur

GE HEAVY DUTY OUTDOOR DIGITAL STAKE TIMER Manuel utilisateur

GE SunSmart Digital Timer Manuel utilisateur

GE 15087 Manuel utilisateur

GE 15136 Manuel utilisateur

GE 15430 Manuel utilisateur

GE SunSmart 15089 Manuel utilisateur

GE 15143 Manuel utilisateur

GE GE 15136 Manuel utilisateur

GE SunSmart 15089 Manuel utilisateur

Manuels Minuteur populaires d'autres marques

Intermatic

Intermatic P1131 Manuel utilisateur

Learning Resources

Learning Resources Time Tracker mini Manuel utilisateur

CEBEK

CEBEK I-215 Manuel utilisateur

Somogyi

Somogyi home TS MD 5 Manuel utilisateur

Profile

Profile 010200280 Manuel utilisateur

Gizmo

Gizmo T4 Manuel utilisateur

Tekmar

Tekmar Timer 031 Manuel utilisateur

Daikin

Daikin DST301B61 Manuel utilisateur

sisel

sisel ENDA ETM2432 Manuel utilisateur

B&Q

B&Q TE103 Manuel d'utilisation et d'entretien

Hozelock

Hozelock AC Plus 2700 Manuel utilisateur

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Manuel utilisateur

Tork

Tork TU40 Manuel utilisateur

Emos

Emos EMT400F Manuel utilisateur

FarmTek

FarmTek Polaris Manuel utilisateur

Maximum

Maximum CRONUS Manuel utilisateur

Uberhaus

Uberhaus TD133B Manuel utilisateur

Clas Ohlson

Clas Ohlson 31-3766 Manuel utilisateur