GE Druck ADTS 542F Guide de configuration

www.gemeasurement.com

GE Data Classification: Public

Druck

ADTS 542F/552F/553F/554F

Air Data Test Set

Safety and Installation Guide

English 1 - 20

Dansk 21 - 40

Deutsch 41 - 60

Español 61 - 80

Français 81 - 100

Italiano 101 - 120

Lietuvių121 - 140

Norsk 141 - 160

Português 161 - 180

Türkçe 181 - 200

Русский 201 - 220

Иކ 221 - 240

঩মୁ 241 - 260

1. Introduction

This manual is applicable to ADTS542F/552F/553F and 554F, referred to as ADTS, and

provides safety and installation information for the Air Data Test Set, compatible with the

requirements of first line operation.

A touchscreen (ADTS Touch) is used to control all required functions. The ADTS Touch can be

positioned on the ADTS or used as a hand held mobile unit via a cable or Bluetooth® wireless

technology. This allows a person to complete the entire test program remotely while

conveniently seated in the aircraft. An ADTS Touch-ER option can be purchased for robust

wireless communications in a large body aircraft. The ADTS Touch can be powered when

positioned on the ADTS, or using a cable connection to the ADTS or battery powered.

The manufacturer has designed this equipment to be safe when operated using the

procedures detailed in this manual.

For details of calibration requirements for the ADTS, refer to User Manual K0553.

For details of available manufacturer specified parts, refer to the current revision of the

product data sheet.

Service/maintenance and repair will be carried out at GE authorized service centers.

Chapter 1. Introduction

1.1 Markings and Symbols

For the list of GE approved service centers, go to:

www.gemeasurement.com

1.2 Intended Use

Test and calibration of aircraft aeronautical pressure instruments located indoor in a hanger

or calibration laboratory or outdoor (non-continuously) on a runway, refer to User Manual

K0553 for further information.

If the equipment is used in a manner not specified by this document and K0553 the

protection provided by the equipment may be impaired.

1.3 Safety

Examine all equipment to be used, paying particular attention to electrical leads and

connectors and pneumatic pipes and connectors. DO NOT use any equipment that is known

to be or suspected to be damaged or faulty.

Symbol Description

This equipment meets the requirements of all relevant European safety directives.

The equipment carries the CE mark.

This symbol, on the equipment, indicates that the user should read the user

manual.

This symbol, on the equipment, indicates a warning and that the user should refer

to the user manual.

This symbol warns the user of the danger of electric shock.

Do not dispose of this product as household waste. Use an approved organization

that collects and/or recycles waste electrical and electronic equipment. For more

information, contact our customer service department, or your local government

office.

The Bluetooth® wireless technology word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of such marks by GE is under

license. Other trademarks and trade names are those of their respective owners.

WARNING This equipment is not rated for use in potentially explosive

atmospheres. Using this equipment in a potentially explosive atmosphere

could lead to serious injury or death.

Power Supply

1.4 Power Supply

1.5 Power Supply Connection

Do not apply electrical power outside the values stated.

Make sure that the power supply is off before connecting the power cable.

The ADTS must be connected to the correct electrical power supply as stated, adjacent to the

power connector.

1.6 Fuses

The two High Breaking Capacity fuses (8) (see Figure 3.1), located in the holders and mounted

on the front panel, protect the unit. The fuses are connected in the live and neutral supply

circuit and are rated at: T5AH 250V.

1.7 Replacing a Fuse

1. Disconnect the electrical power supply.

2. Unscrew the fuse holder cap from the front panel and remove the fuse.

3. Fit a new fuse of the correct size and rating into the fuse holder cap.

4. Secure the fuse holder cap in the front panel.

Single phase 110/230 Vac, 50/60Hz

115 Vac, 400Hz

200 VA Max - ADTS542F/ADTS552F

300 VA Max - ADTS553F/ADTS554F

RISK OF ELECTRIC SHOCK There is a risk of electric shock/

electrocution if there is not a protective earth in place. The ADTS must, at

all times, be connected to the supply protective earth/ground.

The power supply cable and connector must be correctly rated for the

power supply. Only use power cables supplied by GE specifically for the

ADTS.

European Color US Color Function

Brown Black Live

Blue White Neutral

Green/Yellow Green Protective Earth (Ground)

Chapter 1. Introduction

2. ADTS Touch

The ADTS Touch is used to control all required functions. The ADTS Touch can be positioned

on the ADTS or used as a hand held mobile unit via a cable or Bluetooth® wireless technology.

The ADTS Touch will have power applied when:

• Positioned (docked) (1) on a powered-on ADTS.

• Using an umbilical cable connected to a powered-on ADTS.

• Powered from its own battery pack.

• Powered from a universal power supply unit

Figure 2-1: ADTS Touch Docking Connector

The ADTS Touch is equipped with an On/Off switch (2) and USB connectors for connection to

a PC or mass storage device (3).

Figure 2-2: Touch On/Off Switch and USB Connectors

Chapter 2. ADTS Touch

Connector (4) allows connection between the base unit and the ADTS Touch using a 5 metre

or 18 metre umbilical cable.

Note: Only use cables that have been supplied by or purchased from GE.

Figure 2-3: ADTS Touch Umbilical Cable Connector

The ADTS Touch can contain one Lithium-ion battery which is housed in the battery

compartment of the ADTS Touch.

2.1 Replacing the Battery

Figure 2-4: ADTS Touch Battery Compartment

Note: Only use batteries that have been supplied by or purchased from GE.

Prior to replacing the battery, switch the ADTS Touch off. If the ADTS Touch is connected to

the umbilical cable or Docking connector, disconnect prior to removing the battery cover

plate.

Battery Care and Maintenance

1. Unscrew the two thumbscrews (5) of the battery compartment cover plate and

remove the cover plate.

2. Use the tab attached to the battery to slide the battery out of the battery

compartment.

3. Fit a new or re-charged battery into the battery compartment, observing the keyed

orientation.

Note: The battery does not necessarily need to be new or re-charged. The ADTS

Touch will function safely and correctly with a flat battery when the umbilical

cable or dock charging supply is connected.

4. Refit the battery compartment cover plate and tighten the two thumbscrews (5). The

cover must be fitted correctly to maintain protection afforded.

2.2 Battery Care and Maintenance

The battery unit contains a Lithium-ion battery which requires no user maintenance. If

shipping an ADTS Touch and/or battery unit please contact your local service center

beforehand for shipping requirements. Battery must be removed from the ADTS Touch during

transportation. Prolonged exposure to temperature extremes may significantly reduce

battery lifetime. For maximum lifetime, avoid prolonged periods where the battery is exposed

to temperatures outside the range -30°C to +45°C.

The recommended storage temperature range is 5°C to 21°C (41°F to 98.8°F).

The battery is removable. The manufacturer makes the following safety recommendations.

The user should not:

• Short circuit the battery.

• Immerse the battery in any liquid.

• Disassemble or deform the battery.

• Expose to, or dispose of the battery in a fire.

• Subject the battery to excessive physical shock or vibration outside the specified

limits for the ADTS.

• Use a battery that appears to have suffered abuse.

• Charge with an unspecified charger or specified charger that has been modified. This

can cause breakdown of the battery or swelling and rupturing.

• Use a battery in an appliance or purpose for which it was not intended.

The battery unit is sealed for life, so leakage of electrolyte is not expected. If leakage of

electrolyte from the battery is observed, stop using the battery immediately and avoid

contact with the electrolyte. If skin or clothes come into contact with the electrolyte, wash

CAUTION When the battery compartment cover plate is removed and

the ADTS touch is tilted with the battery compartment facing downwards,

the battery can fall out of the ADTS touch causing damage to the battery.

Chapter 2. ADTS Touch

immediately with soap and water. If electrolyte comes into contact with the eyes, wash the

eyes thoroughly with water and consult a doctor immediately.

The ADTS5xxF, ADTS Touch and ADTS Touch-ER contain a Lithium-ion coin cell. This coin cell

is not user replaceable. Installation and replacement shall only be performed by trained

personnel.

Always dispose of batteries safely and in accordance with local instructions.

2.3 Battery Charging

The battery in the ADTS Touch can be charged using one of the following methods:

• By placing the ADTS Touch onto a powered ADTS.

• By connecting the ADTS Touch connector (4) (see Figure 2-3) to the ADTS using the

umbilical cable.

• By using the AATOUCH-5 optional accessory desktop charger. The battery must be

removed from ADTS Touch when it is charged by the AATOUCH-5 desktop charger.

• Using a universal power supply unit connected to the ADTS Touch using an adapter:

Figure 2-5: Universal Power Supply Unit and Adapter

The ADTS Touch universal power supply and the desktop charger are both rated for indoor

use only.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels GE Équipement de test

GE EntelliGuard G Manuel utilisateur

GE SpotChecker Manuel utilisateur

GE Druck MCX-II Manuel utilisateur

GE XL VU Manuel utilisateur

GE Multilin MM300 Manuel utilisateur

GE Druck ADTS 2 Series Manuel utilisateur

GE Mentor EM Manuel utilisateur

GE DMS Go+ Manuel utilisateur

GE Druck DPI 620 Manuel utilisateur

GE PK-2 Manuel utilisateur

GE ADTS542F Manuel utilisateur

GE TVRMS2 Series Manuel utilisateur

GE ADTS552F Guide de configuration

GE Druck DPI612 Manuel utilisateur

GE K0341 Manuel utilisateur

GE ADTS 405F Mk2 Guide de configuration

GE Druck DPI612 Manuel utilisateur

GE Druck DPI611 Manuel utilisateur

GE Druck ADTS 2 Series Manuel d'utilisation et d'entretien

GE Druck DPI 620 Genii Manuel utilisateur

GE Druck ADTS 505 Manuel utilisateur

GE Druck ADTS 405 R/F Mk2 Manuel utilisateur

GE Druck PC6-IDOS Manuel utilisateur

GE Druck DPI 620-IS Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur