GE VAT2000 Series Manuel utilisateur



GE Power Controls

PCST-3299E-R0

VAT2000 AC Drive Series

U2KV23DN1

Speed Detection Feedback

INSTRUCTION MANUAL

NOTICE

1. Read both this manual and VAT2000 Instruction Manual (ST-

3251) before using the U2KV23DN1, and store in a safe place for

reference.

2. Observe the warnings, cautions and other matters described in

this manual.

3. Make sure that this manual is delivered to the final user.

4. The content of this manual can be changed without notice

GE Power Controls

U2KV23DN1 Instruction Manual

- -1

1. Specifications

This manual is for Speed detecting option PCB U2KV23DN1.( Card NPQF-DN09). The option allows

the use of a standard complimentary encoder for speed detection feedback.

Encoder specifications:

Item Specifications

Supply voltage 12VDC±1.2V

Output method Complimentary

Output pulse voltage VH(High revel pulse voltage):above 8.0V , VL(Low revel pulse

voltage):below 1.0V at the terminal on V23-DN1.

Supplied current 150mA (Including signal currents) (Refer Note2 on page 2)

Rising/falling time Within 1µs

Output signal 90º±30º phase difference signal(A phase pulse, B phase pulse)

(Refer Note3 on page 2)

Output pulse

frequency The output pulse frequency is required within 60±10kHz when the

motor rotates at the max. speed.

2. Installation

a) Confirm that the Jumper W1 on U2KV23DN1 is set to 1(2PP) side.

b) Remove the front cover of VAT2000S

CAUTION

There is a risk of electric shocks.

The VAT2000S has a built-in electrolytic capacitor, so a charge will remain even when the inverter power is turned OFF. Always

observe the following times before carrying out wiring work.

• Wait at least 20 minutes after turning the power OFF before starting work. Make sure that thedisplays on the operation panel

have gone out before removing the cover.

• After removing the cover, confirm that the "CHARGE" LED in the VAT2000S does not light. Also check that the voltage

between terminals L+1 or L+2 and L– is 15V or less before starting the inspections. (Check with the "CHARGE" LED if the

unit is not provided with the L– terminal.)

c) Install U2KV23DN1 to the position Option I on the Control PCB cover and make sure not to bend the

pins of reverse of U2KV23DN1.

U2KV23DN1 Instruction Manual

- -2

3. Wiring

An example of the encoder connection is given below.

Note 1: The option U2KV23DN1 is card number NPQF-DN09.

Note 2: If the current to encoder exceeds 150mA, use an external power supply. In this case, connect

the external power source only to the encoder. DO NOT connect the power source to TB1-

1,2[12KP] or -3[0KP] on U2KV23DN1.

Note 3: Below drawing shows A, B encoder phases when motor rotates forward.

A phase

pulse

B phase

pulse

90º 90º 90º 90º

12V

2.2KΩ

1KΩ

470

TB1

-1,2[12KP]

-3[0KP]

-7[PA]

-8[0KP]

-9[PB]

-10[0KP]

DC12V Max.150mA

(Refer Note2 on page 2)

[A phase pulse output]

[B phase pulse output]

[common]

-11[PAOUT]

-13[PBOUT]

-12,-14[0KP]

A phase

pulse

B phase

pulse

Set W1 to 1(2PP)side.

2PP

Suitable cable for encoder

0.75mm2(50m or less), 6-core twisted shield strands

U2KV23DN1(NPQFDN09)

1PP

Encoder

3.3KΩ

12V

ENCODER

DC12V Max.150mA

TB1

-1,2[12KP]

-3[0KP]

U2KV23DN1

12V

Power

source

Autres manuels pour VAT2000 Series

Table des matières

Autres manuels GE Capteur de sécurité

GE KL700 Series Manuel

GE KM170 Manuel utilisateur

GE PrecisionLine RCR-90 Manuel utilisateur

GE 868 GEN2 Manuel utilisateur

GE 45132 Manuel utilisateur

GE DD205-AD Series Manuel utilisateur

GE DD205RF/60-947-8A Series Manuel utilisateur

GE VE1016 Series Instructions de montage

GE Baker Hughes Reuter-Stokes Flame Tracker... Manuel utilisateur

GE Motion Sensor Manuel utilisateur

GE ARITECH 1500 Series Manuel du produit

GE KL700 Series Manuel utilisateur

GE SB250 Manuel utilisateur

GE INDOOR/OUTDOOR PIR MOTION SENSORS... Manuel utilisateur

GE H-10 Manuel d'utilisation

GE VE1012 Series Instructions de montage

GE DDI602 Instructions de montage

GE VersaSafe VersaPoint Series Manuel utilisateur

GE VE1100 Series Instructions de montage

GE GS930 Manuel utilisateur

GE 869 Manuel utilisateur

GE Interlogix ARITECH 1500 Series Manuel du produit

GE EV435AM-AD Series Manuel utilisateur

GE 60-639-95R Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur