GE RM84911 Manuel utilisateur

Universal Remote

Instruction Manual

RM24911

RM84911

rev. 11/05

Congratulations on your purchase of the RM24911

Universal Remote Control. The RM24911 is one

of the most easy to use remote controls available

today. With the RM24911, juggling multiple remote

controls is a thing of the past! Your RM24911

controls up to three devices, including the most

popular brands of TV, VCR, DVD, CBL, and SAT.

The RM24911 is easy to use, easy to program,

and it gives you total control—at the touch of your

ﬁngertips!

Note: Some functions from your original remote

may not be controlled by this remote. Use the

original remote, if available, to control such

functions. Sometimes buttons other than described

in these instructions may actually perform the

function. For example, the CHAN and VOL

buttons might be used to navigate through menu

choices. We recommend you experiment with the

remote to identify if such situations pertain to your

equipment.

Introduction

............................................................

Setup

.....................................................................

Battery Installation

............................................

Battery Saver

....................................................

Battery Saver....................................................

Battery Saver

Code Saver

......................................................

Code Saver ......................................................

Code Saver

Code Setup

......................................................

Button Functions

..............................................

Direct Code Entry

.............................................

Code Search

....................................................

Using Your Remote

...............................................

Code Identiﬁcation

............................................

Using SHIFT

.....................................................

Sleep Function

...............................................

Controlling Devices with Power On and Off ... 11

Controlling Combo Devices............................ 11

VCR/DVD/DVR Punch-Through..................... 11

Volume/Mute Control and Punch-Through ..... 12

All Volume/Mute Control to any one Mode ..... 12

Setting any Mode for its own Volume/Mute .... 13

Troubleshooting

...................................................

Table of Contents

Battery Installation

1. On the back of the remote, push down on the

tab and lift the cover off.

2. Match the batteries to the + and - marks inside

the battery case, then insert 2 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will

save your batteries should your remote get stuck in

a place where the buttons remain depressed (e.g.,

between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote.

If buttons are pressed without batteries in the

remote, all codes will be lost.

Code Setup

The

SETUP

button is used to setup the remote.

You can either setup the remote using the code

tables (on separate sheet), or you can search

through the library of codes until you ﬁnd a code

that works for your product.

Please refer to “ Code

Search” on page 7 for more information on using

the code search feature to learn how to search

through the library of codes for your products.

NOTE: You can store any kind of code under any

mode (except TV). I.E. you can store a VCR code

under the

CBL/SAT

button, or a Cable code under

the

DVD/VCR

button, etc. However, you can only

store TV codes under the

button.

Setup

RECORD, PLAY, STOP,

REW, FF, PAUSE

VCR

control buttons operate

your VCR even when the

remote is set to operate

the TV. Also operates DVD

Scan -/+. Note the VCR

buttons also control DVD

when in DVD Mode.

Some buttons on the remote might have functions that

are referred to by different names on the device you

are controlling. E.G.

PREV.CH

may be called RECALL,

ENTER

may be called DISPLAY. These differences

depend on the brand and model of your product. Also,

this remote can only operate features that exist on your

product. E.G., your product must have

PREV.CH

ability

for the

PREV.CH

button to operate this feature.

TV, CBL/SAT, DVD/VCR

Selects product to be oper-

ated.

Red Indicator

Lights when any

button is pressed.

PREV.CH

Returns to

the previously selected

channel.

Button Functions

INFO

button brings up DVD

Display or Control Menu for

Chapter/Track/Title number,

Time remaining/elapsed,

system information, etc. Also

displays on-screen channel

information.

Press and release

SHIFT/SETUP

then

MENU/

INFO

to display the Menu on

the TV. See “Using

SHIFT

for

Menu and Navigation” de-

scription on Page 9 for more

information.

VOLUME UP/DOWN

Changes the volume

level of the product,

normally the TV.

NUMBERS

Enter numbers for direct

channel selection. Some

products require ENTER to

be pressed after channel

selection.

ON•OFF

Turns

product On or Off.

CHANNEL Up/Down

Changes the channels.

Button Functions, cont.

INPUT

For some TVs, press repeatedly

to select from available viewing

sources (antenna, cable box,

VCR, etc.).

SETUP

Used to setup the remote,

and for code search function.

SHIFT

Press and release to access buttons

labeled in reverse print (OK, MENU, EXIT).

See “Using

SHIFT

for Menu and Navigation”

description on Page 9

for more information.

Note: The

REC

button must be pressed TWICE to record

from your VCR. For some brands of VCRs, you might

need to press the

REC

button once, then press it again

for three seconds.

ENTER

For some TV models,

used after direct chan-

nel number entry to

immediately change to

the selected channel.

MUTE

Turns off the

TV sound while the

picture remains.

Selects menu

items for the device

you are controlling.

SLEEP

enables the remote to

turn off your TV after a period

of 1 to 99 minutes.

EXIT

Exits On-Screen Menus

and/or Returns to previous On-

Screen selection.

Write your codes down here for easy reference

later.

Direct Code Entry

1. Press and hold the

SETUP

button until

the red indicator stays on, then release

the

SETUP

button.

2. Press and release the desired device

button (

VCR

, etc.). The red indicator

blinks, then stays lit.

3. Enter the 3 digit code

from the code tables

(on separate sheet).

Note: after a valid

code entry, the red

indicator turns off. For

an invalid code, the

red indicator ﬂashes.

4. With your device on, press

ON•OFF

If the device turns off, no further

programming is required. Note: If

some buttons do not operate your

equipment, try one of the other

codes for your brand.

Device Device stored Code

TV TV

CBL/SAT

DVD/VCR

Device Device stored Code

TV TV

Device Device stored Code

Code Search

If your device does not respond after you have

tried all the codes for your brand, or if your brand is

not listed, try searching for your code by following

these steps.

1. Manually turn on the device (

VCR

, etc.) to

be controlled.

2. Press and hold the

SETUP

button

until the red indicator stays on, then

release the

SETUP

button.

3. Press and quickly release the desired

device button (

VCR

, etc.). The

red indicator blinks off once.

4. Press the

ON•OFF

button

repeatedly (up to 300 times) until

the device to be controlled turns

off. The red indicator blinks off with

each button press.

Most users will store VCR codes under the

VCR

button, Cable codes under

CABLE

, etc. If (for

example) you want to store a VCR code under

CABLE

, ﬁrst follow the procedure for Direct Code

Entry (previous page) and press

CABLE

in step 2

of Direct Code Entry, then enter ANY VCR code in

step 3 of Direct Code Entry. Then follow the steps

above for Code Search.

Note

: Code Search starts from the currently

stored three digit number under that mode.

Sometimes the ﬁrst code that “works” with your

device may only allow limited functionality (e.g.

the MENU button might not work). There may be

a code that performs more functions. Continue the

code search process until the best code is found.

5. Press and release

ENTER

to install the

code.

Using Your Remote

Code Identiﬁcation

The Code Identiﬁcation Feature allows you to

identify the three digit library code stored under

your device button. For example, if you want to ﬁnd

out what three digit code is stored under your TV

device button, follow the six steps below:

1. Press and hold the

SETUP

button until

the red indicator stays on. Release the

SETUP

button.

2. Press and release the desired

device button (

VCR

, etc.). The

red indicator blinks, then stays lit.

3. Press and release the

SETUP

button.

The red indicator blinks once and

remains lit.

4. To ﬁnd the ﬁrst digit

for the code stored

under the device

button pressed in step

2, press each numeric

button from

0-9

turn. The number that

causes the indicator

light to blink is the ﬁrst

digit in your code.

5. To ﬁnd the second digit, repeat step 4.

6. Repeat step 4 again to ﬁnd the third digit. This

time the red indicator turns off and stays off.

Using Your Remote, cont.

For MENU, press and release

SHIFT/SETUP

then

MENU/INFO

For OK, press and release

SHIFT/SETUP

then

OK/MUTE

For EXIT, press and release

SHIFT/SETUP

then

EXIT/

SLEEP

For Up, Down, Left or Right

Navigation, press and release

SHIFT/

SETUP

followed by the respective

Using SHIFT for Menu and Navigation

The

SHIFT

button allows access to more than one

function for certain buttons.

Use the

SHIFT/SETUP

button prior to accessing

the

EXIT

and Navigation functions

e.g.:

Using Your Remote, cont.

Sleep Function

The Sleep button enables the remote to turn off

your TV after a period of 1 to 99 minutes as shown

below. The remote must be in TV mode to set a

Sleep Timer. This feature works even if your TV

does not have a sleep feature.

1. Press and release the TV device but-

ton.

2. Press and hold the Sleep button until the

onds).

3. Release the Sleep

button.

4. Press and release

the numeric buttons

(01-99) for the time

required. The LED will

blink off to indicate button press acceptance.

5. TV Sleep Timer is set.

6. Leave the Remote pointing towards the TV

with an unobstructed path.

To cancel the Sleep Timer, press and hold the

Sleep button until the LED blinks, or press and

LED remains lit (about 2-3 sec-

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation

Invacare

Invacare G91S Manuel utilisateur