Garmin VARIA UT800 Manuel utilisateur
VARIA™UT800
Owner’s Manual
© 2017 Garmin Ltd. or its subsidiaries
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or
improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to
www.garmin.com for current updates and supplemental information concerning the use of this product.
Garmin®, the Garmin logo, ANT+®, and Edge® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Garmin Connect™, Garmin Express™, and
Varia™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
This product is ANT+® certified. Visit www.thisisant.com/directory for a list of compatible products and apps.
M/N: A03086
Table of Contents
Introduction..................................... 1
Installing the Out-Front Mount............... 2
Installing the Helmet Mount...................5
Device Overview...................................... 6
Turning On the Device............................ 6
Bike Light Status LEDs........................... 6
Device Settings................................ 6
Pairing Your Bike Light with Your Edge
830 or 1030............................................. 7
Customizing Headlight Settings with
Your Edge Device.................................... 7
Automatic Beam Intensity...................... 8
Device Information........................... 9
Specifications......................................... 9
Charging the Device............................. 10
Tips for Charging the Device................10
Device Care........................................... 10
Troubleshooting.............................11
Resetting the Device............................. 11
Thermal Safety Shutdown.................... 11
Low Temperature Battery
Conservation......................................... 11
Updating the Headlight Software With
Your Edge Device.................................. 11
Product Updates................................... 11
Getting More Information.....................11
Other Compatible Devices.............. 12
Pairing Your Bike Light with Another
Edge Device...........................................12
Pairing the Remote with Your Varia
Device.................................................... 12
Index..............................................13
Table of Contents i
Introduction
WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other
important information.
The device is intended for outdoor use. Without proper airflow during use, the device may become hot. Handle
with care.
Introduction 1
Installing the Out-Front Mount
You can use the out-front mount to install the headlight and your Edge® device. Garmin recommends that you
adjust the mount for the Edge viewing angle before you install and adjust the headlight angle.
1Select a secure location to mount the Edge device and headlight where they do not interfere with the safe
operation of your bike.
2Use the 2.5 mm hex key to remove the screw from the handlebar connector .
3If necessary, remove the two screws on the top of the mount , rotate the connector, and replace the
screws to change the orientation of the mount for an Edge device.
4Place a rubber pad around the handlebar:
• If the handlebar diameter is 25.4 mm, use the thicker pad.
• If the handlebar diameter is 31.8 mm, use the thinner pad.
5Place the handlebar connector around the rubber pad.
NOTE: You should align the contours on the rubber pad with the grooves on the inside of the handlebar
connector.
6Replace the screw, and use the 2.5 mm hex key to tighten the screw.
NOTE: You should check the tightness of the screw periodically.
7Install the Edge device, and adjust the mount (optional).
8Connect the quarter-turn adapter to the headlight.
2 Introduction
9Insert the screw , and hand tighten.
10 Align the notches of the quarter-turn adapter with the tabs on the bottom of the mount.
11 Press up slightly, and turn the adapter counterclockwise until it locks into place.
12 Adjust the headlight angle so it is parallel to the ground, and use the 4 mm hex key to tighten the screw.
Introduction 3
NOTE: You should check the tightness of the screw periodically.
4 Introduction
Installing the Helmet Mount
1Select a secure location to mount the headlight where it does not interfere with the safety and comfort of
your helmet.
2Attach the mount using both straps.
3Lock the straps by pressing down the clasp.
4Connect the adapter to the headlight.
5Insert the screw , and hand tighten.
6Align the tabs on the adapter with the notches of the mount.
The lever must be in the open position.
7Insert the device into the mount.
8Snap the lever to the closed position to lock the device into the mount.
Introduction 5
The lever must be flush with the base.
9Adjust the headlight angle, and use the 4 mm hex key to tighten the screw.
NOTE: You should check the tightness of the screw periodically.
Device Overview
Device key
Hold for 1 sec. to turn the device on.
Hold for 2 sec. to turn the device off.
Hold to enter pairing mode (Pairing Your Bike Light with Your Edge 830 or 1030, page 7).
Select to change operating modes.
Status LED View device status (Bike Light Status LEDs, page 6).
Turning On the Device
1Hold the device key for 1 second.
The first time you turn on the device, it enters pairing mode. The status LED flashes purple. The device can
be paired with a wireless remote or Edge device.
2Hold the device key for 2 seconds to turn off the device.
The next time you turn on the device, it is in high intensity mode.
Bike Light Status LEDs
LED Activity Status
Solid red An error occurred while charging, or the device shut down to prevent overheating.
Flashing red The battery is low.
Flashing green The battery is charging.
Solid green Charging is complete.
Flashing blue The device is in smart mode and can be controlled by a paired wireless remote or
Edge device.
Flashing purple The device is in pairing mode.
Alternating blue and green The device is uploading software.
Device Settings
You can remotely control your Varia devices and customize settings using your compatible Edge device. This
section contains instructions for the Edge 830 and 1030 devices. Other compatible Edge devices use similar
settings.
6 Device Settings
Autres manuels pour VARIA UT800
2
Table des matières
Autres manuels Garmin Lampe de poche
