Gardsman CTC-1745 Manuel utilisateur
D.D. 31-Dec-08
Table of Contents
1. Introduction _______________________________________________________ 2
2. Application Overview _______________________________________________ 2
2.1. Identifying the Parts ___________________________________________________ 2
2.2. The Power Supply_____________________________________________________ 4
2.3. System Requirements__________________________________________________ 4
3. Getting Started_____________________________________________________ 5
4. Hardware Installation for CTC-1745____________________________________ 5
5. Software Installation for CTC-1745 ____________________________________ 6
5.1 Running the CTC-1745 Finder____________________________________________ 6
5.2 Configure Setting______________________________________________________ 7
6. Connecting to Webpage _____________________________________________ 8
7. Setting the system_________________________________________________ 10
7.1. Report______________________________________________________________ 10
7.2. Mobile______________________________________________________________ 14
7.3. Center______________________________________________________________ 16
7.4. Code Setting ________________________________________________________ 17
7.5. Dynamic DNS________________________________________________________ 19
7.5. Administrator________________________________________________________ 20
8. Sensor Learning & Bypass__________________________________________ 21
8.1. Add Sensor _________________________________________________________ 21
8.2. Learning KP-18 in the Control Panel (Locally)_____________________________ 27
8.3. Learning KP-9/KP-A9 in the Control Panel (Locally) ________________________ 28
8.4. Learning BX-15 in the Control Panel (Locally)_____________________________ 28
8.5. Learning SR-15 in the Control Panel (Locally)_____________________________ 29
8.6. Bypass _____________________________________________________________ 30
9. Program the System _______________________________________________ 31
9.1. Panel Condition______________________________________________________ 31
9.2. PIN Code ___________________________________________________________ 32
1
9.3. Panel Settings _______________________________________________________ 34
9.4. Date & Time _________________________________________________________ 37
10. Surveillance _____________________________________________________ 38
8.1. Cameras____________________________________________________________ 38
10.2. Viewer_____________________________________________________________ 41
10.3. Captured Events ____________________________________________________ 42
11. Network Setting __________________________________________________ 44
11.1. Network ___________________________________________________________ 44
11.2. Wireless Setting (Only for Wi-Fi version) ________________________________ 45
11.3. UPnP______________________________________________________________ 48
12. System Management & History Records______________________________ 49
12.1. Firmware __________________________________________________________ 49
12.2. Firmware / Alarm (Panel Firmware Update) ______________________________ 50
12.3. Factory Reset_______________________________________________________ 51
12.4. Log _______________________________________________________________ 52
12.5. History Records_____________________________________________________ 53
2
1
3
2
4
5
2
1. Introduction
This section covers unpacking your IP Security System with CTC-1745 IP Panel, Security
Sensors and CTC-215 IP Camera (if purchased). Refer to later chapters for information on
setting up and configuring the system over the Web Page in more detail.
IP Security System advanced with fully integrated TCP/IP technology with Ethernet and Radio
connectivity to take full advantage of new advances in IP Home Security and Home Automation
and multi-path signalling.
The system can also include up to 4 wired / wireless CTC-215 IP Cameras. Each CTC-215 can
be assigned to different devices, which will captures burglar images with any trigger.
2. Application Overview
2.1. Identifying the Parts
Area 1 status LED (Dual Colour - Red & Green)
zRED LED ON – indicates that the Area 1 is currently in Arm Mode
zRED LED FLASHES – indicates that the Area 1 is currently in Home / Day Home /
Night Home Mode
zGREEN LED ON – indicates that the Area 1 is currently in Disarm Mode.
zGREEN LED FLASHES – indicates that the Area 1 is currently in Learn Mode.
zLED OFF – indicates that the Area 1 is currently in Walk Test Mode
Area 2 status LED (Dual Colour - Red & Green)
zRED LED ON – indicates that the Area 2 is currently in Arm Mode
zRED LED FLASHES – indicates that the Area 2 is currently in Home / Day Home /
Night Home Mode
zGREEN LED ON – indicates that the Area 2 is currently in Disarm Mode.
zGREEN LED FLASHES – indicates that the Area 2 is currently in Learn Mode.
1
3
3
zLED OFF – indicates that the Area 2 is currently in Walk Test Mode
Panel Status (inl. Area 1 & 2) LED (Dual Colour - Yellow & Green)
zGREEN LED ON – indicates that there is alarm memory in the system.
zGREEN LED FLAHES – indicates that Panel is alarming
zYELLOW LED ON – indicates that there is fault in the system
zLED OFF – indicates that the system is normal operation mode
Internal Buzzer
Standing Base
Learn Button
Use Learn Button to locally learn Remote Keypads (KP-9/KPA-9) into the panel.
Wi-Fi Antenna
(only available with Wi-Fi version)
Internet Connection
Internet Cable connection from wall
DC Jack
DC 12V 1.5A (12V 2A for Wi-Fi version) switching power connection.
Power Switch
(RJ-11) Programming Jack
GSM SIM Card Base
This slot is for inserting SIM card.
4
5
6
8
9
7
4
2.2. The Power Supply
An AC power adapter is required to connect to a wall outlet. Be sure only to use an adapter with
the appropriate AC voltage rating to prevent component damage. A DC 12V 1.5A (2A for Wi-Fi
Version) switching power is generally used to power the Control Panel.
Rechargeable Battery
zIn addition to the adapter, there is a rechargeable battery inside the Control Panel, which
serves as a back up in case of a power failure.
zWhen CTC-1745 connects to the Internet via wired connection, the battery used is a Ni-MH
780 mAH 7.2V rechargeable battery.
zDuring normal operation, the AC power adapter is used to supply power to the Control
Panel and at the same time recharge the battery.
zWhen the battery is fully charged, it can provide back-up power for a period of about 10
hours. It takes approximately 48 hours to fully charge the battery.
<
<N
NO
OT
TE
E>
>
)If the AC power is missing and the battery is near exhaustion, or if the battery is missing,
a low battery or a battery not connected message will be displayed and the internal
siren will be disabled to conserve power.
2.3. System Requirements
The system requires a TCP/IP network environment. CTC-1745 IP Panel and/or CTC-215 IP
Camera can be attached into your Network.
To install the CD Wizard, your computer must have:
zMicrosoft Windows 98, ME, NT4.0, 2000, XP, or Vista operating system. AMac or Linux
based machine is also compatible.
zMicrosoft Internet Explorer 5.x, or later and Mozilla Firefox 1.0 compatible.
zCD-ROM drive
zCPU: Intel Pentium II 266MHz or above
zMemory: 32MB (64MB recommended)
zVGA resolution: 800x600 or above
5
3. Getting Started
Read this section of the manual to learn how to set up your CTC-1745 IP Panel and program
System Settings over the Web page.
With a valid Internet connection, this system will bring you the freedom to Monitor / Access /
Control your IP Security System at anywhere, anytime in the world.
4. Hardware Installation for CTC-1745
Step 1. Connect the DC 12V 1.5A Table-top Power Adaptor to a Wall Outlet and the other end
to CTC-1745. A short beep will be performed with Power LED lights ON.
Step 2. Plug-in the Internet connection cable into the Internet Jack on CTC-1745. Plug-in the
other end of the enclosed Internet cable into your Internet Router port.
With Wired Connection: Once the Internet Set-up is successful, please leave the cable
connected.
With Wi-Fi (Wireless) Connection: Once the Internet Set-up is successful, you can
remove the Internet connection cable to enjoy its wireless operation.
Step 3. CTC-1745 Panel features built-in GSM communication facility to report to the
Monitoring Station. The GSM SIM Card Base is situated inside the Power Supply
compartment. Please insert the SIM card.
Step 4. Insert the SIM card into the slot as shown in the below picture.
Step 5. Hardware installation for CTC-1745 is now complete.
6
5. Software Installation for CTC-1745
You need to use the supplied CTC-1745 Finder software to set the IP Panel up for the first time
in order to find it in the network.
5.1 Running the CTC-1745 Finder
To install the CTC-1745 Finder software
Step 1. Insert the supplied CD-ROM into your CD-ROM drive
Step 2. If the installation does not start automatically, use a file explorer
application to execute setup.exe in the root folder on the CD-ROM.
Step 3. Find the FinderV1.3 software icon in the CD-ROM.
Step 4. Double click on the FinderV1.3 to initiate the installation.
Step 5. Click Next to re-name the shortcut folder, if no renaming is required; please click Next
to get ready for the installation process.
Step 6. Another click on Next to begin the Installation; once the installation is complete, click
Finish to confirm.
Step 7. Anew icon will be displayed on your desktop.
Step 8. Double click on the Finder.exe to start the installation. The following screen will be
displayed:
Step 9. Click on Search, It will start searching for recognized IP address within the Local
Network Service.
Step 10. You will be able to locate the current CTC-1745 IP address among the list, displayed
with MAC Address and Product name.
7
Step 11. Once CTC-1745 is identified, click on Open Web Page to be automatically linked to
the IP Security System Web page.
Step 12. Software installation for CTC-1745 IP Panel is now complete.
5.2 Configure Setting
The Configure setting is for you to enter the Internet data manually.
Step 1. Click on Configure Setting, the following window will display:
Step 2. Enter the internet data and the CTC-1745’s web user name and password.
(Default) User Name: admin
(Default) Password: admin1234
Step 3. Click on OK to confirm. When the username and password are correct, a window will
display: Status: Configure success!!
8
6. Connecting to Webpage
Step 1. The Webpage can be opened by Finder (please see section 5.5.1, step 10) or with a
valid Internet connection, double click on Internet Explorer icon to initial its webpage.
Under Address section (highlighted in RED), enter CTC-1745’s IP address (for
example, http://192.168.1.198), and click GO. You will enter the welcome Webpage.
Step 2. Click on I’m already a customer. Enter Alarm Panel. It is required to enter the web
User name & Password.
Table des matières
Autres manuels Gardsman Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur