Galcon 11000BT Manuel utilisateur
11000BT Bluetooth
Hose-End Battery Operated
Irrigation Controller
Kfar-Blum 1215000, Tel. 972-4-690-0222, Fax. 972-4-690-2727
- 1 -
HOSE END TIMER
1.Controller body
2. Interior lter
3. Base
4. Controller display
5. Programming and operation buttons
6. Male hose thread connection
7. Battery compartment
8. Female swivel hose thread faucet/tap adaptor
1. PARTS IDENTIFICATION
2 5
4
1
6
3
7
8
- 2 -
2. BATTERY INSTALLATION
• Turn the controller to the position were the
display is facing you
• Remove the battery compartment cover
• Connect 9V battery to the battery connector
• Insert battery and press on battery cover
• Pay attention: when changing the
battery, make sure the battery compartment
stays dry.
Use Alkaline batteries only
Please note: when nished, always turn the
controller back to the original position: the
display is covered by the base
- 3 -
3. CONTROLLER/TIMER INSTALLATION
Make sure the lter (washer) is in place, then
screw the controller to the faucet/tap by attaching
the side with the female swivel hose thread
connector to the faucet or hose end, then turn it
clockwise (hand tighten only).Connect the
controller hose male thread side to your system.
- 4 -
4. IRRIGATION PROGRAMMING
This section contains an example of weekly
irrigation program. Simply alter data in the
example to adapt the program to meet your
irrigation requirements.
The digital controller is programmed with the aid
of 4 buttons.
Programming step – used to select the
appropriate programming mode (e.g. clock
setting mode).
Parameter selection – used to select the
parameter to be changed (e.g.hour,
minute,etc.) To implement the change, the
selected parameter must be blinking.
Data increment (increase) – raises the
value of the selected parameter (e.g. adds
an hour)
Data decrement (decrease) – lowers the
value of the selected parameter (e.g.
deducts an hour).
- 5 -
If no changes are implemented, the controller
display will always revert to the main screen
(clock).
Display digits will stop blinking after 40 seconds.
If the last parameter stops blinking before you
have completed your programming, press to
continue the process.
Emergency Irrigation: After inserting batteries if
no buttons are pressed,the clock will blink
continuously.After 10 minutes, the controller will
implement 5-minute irrigation on a 24-hour cycle.
SETTING CURRENT TIME & DAY OF THE
WEEK
Setting The Clock
To enable the irrigation controller to operate the
irrigation system at the required times, the current
time and day of the week must be set as shown
below:
- 6 -
1. Press several times until appears.
2. Press . The hour digits blink. Set the current
hour with the aid of or .
3. Press . The minute digits blinks. Set the
current minute with the aid of or .
- 7 -
Setting The Day Of The Week
1. Press until a blinking drop appears at the
top of the display.
2. Set the drop on the current day of the week
by pressing on or .
For a 24 hour clock display, press concurrently
on and buttons once the hour digits stop
blinking.
Pressing these buttons again will revert the
display back to AM/PM hour display.
- 8 -
PROGRAMMING A WEEKLY IRRIGATION
SCHEDULE (SET DAYS OF THE WEEK)
Let's assume that we want to program the
irrigation controller to water three times a day, at
8:00 a.m., 1:00 p.m. and 7:00 p.m., for 10
minutes each time, on Tuesday and Friday.
PROGRAMMING DURATION OF IRRIGATION
1. Press until appears opposite "Duration".
The digits blink (0)
2. Press on or to change the watering
duration in the example.
Please note: after rst 15 minutes,
the duration will be set in 15 minutes
intervals
- 9 -
PROGRAMMING IRRIGATION DAYS
1. Press . will appear opposite the word
'Days'. If you are programming the controller
for the rst time, the word OFF will blink on
the display.
2. Press . A blinking will appear under
Monday in the upper section of the display.
Using , position the blinking marker under
Tuesday, and press . The marker under
Tuesday will stop blinking and another marker
will start blinking under Wednesday. Press
twice more until the blinking marker reaches
Friday. Press again.
Table des matières
Autres manuels Galcon Contrôleurs
Galcon
Galcon Galileo Manuel
Galcon
Galcon 6100 Series Manuel utilisateur
Galcon
Galcon S Series Manuel utilisateur
Galcon
Galcon AC 4 Manuel utilisateur
Galcon
Galcon 61 Series Manuel utilisateur
Galcon
Galcon Dc-1 Manuel utilisateur
Galcon
Galcon 7101BT Manuel utilisateur
Galcon
Galcon Galileo Manuel utilisateur
Galcon
Galcon G.S.I DC Manuel d'utilisation
Galcon
Galcon Gal Pro DC Manuel utilisateur
