GAI-Tronics XCP0030A Manuel utilisateur

Pub. 43003-014B

GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA

610-777-1374 n800-492-1212 nFax: 610-775-6540

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

GAI-TRONICS® CORPORATION

A HUBBELL COMPANY

Model XCP0030A Telco Interface Kit

Field Installation Kit Instructions

Confidentiality Notice

This manual is provided solely as an operational, installation, and maintenance guide and contains

sensitive business and technical information that is confidential and proprietary to GAI-Tronics.

GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,

and such information may only be used in connection with the operation of your GAI-Tronics product or

system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any

third party.

General Information

The Telco Interface Kit adapts the three DB25 rear panel connectors to a single 50-pin standard

connector. The unit mounts on the rear panel of the ICP9000 Series Desktop Console, ICP9000

Navigator Series MCU, or the Supervisor option installed on the respective unit, and plugs into the three

DB25 connectors, P40 (a) (b) (c).

The Model XCP0030A 25-Pair Telco Interface Kit includes the following components:

Qty Description

1Telco Interface Adapter

2#6-32 ×1.625-inch Phillips screws

Installation

ICP9000 Series Desktop Console

1. Disconnect the power from the ICP9000 Series Desktop Console and remove all attached land-line

and accessory cables from the rear of the unit.

2. Mount the Telco Interface to the rear panel of the console or the Supervisor panel. Refer to Figure 1

or Figure 2. Position the Telco Interface so that the three DB25 connector plugs line up with the

DB25 connector receptacles on the rear panel.

3. Secure the Telco Interface with the supplied #6-32 screws shown in Figure 1 or Figure 2, tightening

them until the Telco unit is snug against the rear panel or the Supervisor panel.

Pub. 43003-014B

Model XCP0030A Telco Interface Kit Page: 2of 4

11/02

Figure 1.

Figure 2.

Pub. 43003-014B

Model XCP0030A Telco Interface Kit Page: 3of 4

11/02

4. Plug one end of a standard DB50 connector plug into the single 50-pin Telco connector and terminate

the other end to an applicable punch block. Place the connector plug bracket over the 50-pin

connector and secure with two screws. The bracket secures the connector to the Telco interface.

5. Reattach the necessary accessory cables and reconnect the power.

Note: The Supervisor unit input connectors and output connectors can each have a separate Telco

Interface unit attached.

ICP9000 Navigator Series MCU

1. Disconnect the power from the ICP9000 Navigator Series MCU and remove all attached land-line

and accessory cables from the rear of the unit.

2. Mount the Telco Interface to the rear panel of the console or the Supervisor panel. Refer to Figure 3

or Figure 4. Position the Telco Interface so that the three DB25 connector plugs line up with the

DB25 connector receptacles on the rear panel.

3. Secure the Telco Interface with the supplied #6-32 screws shown in Figure 3 or Figure 4, tightening

them until the Telco unit is snug against the rear panel or the Supervisor panel.

4. Plug one end of a standard DB50 connector plug into the single 50-pin Telco connector and terminate

the other end to an applicable punch block. Place the connector plug bracket over the 50-pin

connector and secure with two screws. The bracket secures the connector to the Telco interface.

5. Reattach the necessary accessory cables and reconnect the power.

Note: The Supervisor unit input connectors and output connectors can each have a separate Telco

Interface unit attached.

Figure 3.

Pub. 43003-014B

Model XCP0030A Telco Interface Kit Page: 4of 4

11/02

Telco Interface Pin Connectors

Pair # (Pin #) Pin Function (Pin #)

(for dc pos, neg) Pair # (Pin #) Pin Function (Pin #)

(for dc pos, neg)

1 (1, 26) TX 1 (14, 15) 13 (13, 38) TX 7 (8, 9)

2 (2, 27) RX 1 (1, 2) 14 (14, 39) RX 7 (10, 11)

3 (3, 28) TX 2 (3, 4) 15 (15, 40) TX 8 (12, 13)

4 (4, 29) RX 2 (5, 6) 16 (16, 41) RX 8 (24, 25)

5 (5, 30) TX 3 (8, 9) 17 (17, 42) TX 9 (14, 15)

6 (6, 31) RX 3 (10, 11) 18 (18, 43) RX 9 (1, 2)

7 (7, 32) TX 4 (12, 13) 19 (19, 44) TX 10 (3, 4)

8 (8, 33) RX 4 (24, 25) 20 (20, 45) RX 10 (5, 6)

9 (9, 34) TX 5 (14, 15) 21 (21, 46) TX 11 (8, 9)

10 (10, 35) RX 5 (1, 2) 22 (22, 47) RX 11 (10, 11)

11 (11, 36) TX 6 (3, 4) 23 (23, 48) TX 12 (12, 13)

12 (12, 37) RX 6 (5, 6) 24 (24, 49) RX 12 (24, 25)

Figure 4.

Table des matières

Autres manuels GAI-Tronics Récepteur

GAI-Tronics

GAI-Tronics 12550-102 Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur