Futek IPM650 Manuel utilisateur

Quick Start Guide
Sensor Solutions Source
Load · Torque · Pressure · Multi Component · Calibration · Instruments · Software
www.futek.com
IPM650
Intelligent Panel-Mount Display

2
Getting Help
SP1184-A
FUTEK reserves the right to modify its design and specifications without notice.
Please visit http://www.futek.com/salesterms for complete terms and conditions.
10 Thomas, Irvine, CA 92618 USA
Tel: (949) 465-0900
Fax: (949) 465-0905
www.futek.com
TECHNICAL SUPPORT
For more IPM650 support, please visit: http://www.futek.com/ipm650/support.aspx

3
Display Features . . . . . . . . . . . . . . . . . . . . . 4
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connector Pin Configuration. . . . . . . . . . . . . . . 6
Wiring Layout . . . . . . . . . . . . . . . . . . . . . . 7
Profile Quick Setup (Calibration) . . . . . . . . . . . . . 9
TEDS and Channel Select . . . . . . . . . . . . . . . .11
Profile Lockout and LCD Settings . . . . . . . . . . . .12
Analog Output Quick Setup . . . . . . . . . . . . . . .13
Alarm and Relay Quick Setup . . . . . . . . . . . . . .14
Data Logging. . . . . . . . . . . . . . . . . . . . . . .16
SENSIT Test and Measurement Software . . . . . . . .18
Performance Review . . . . . . . . . . . . . . . . . . .20
Specifications . . . . . . . . . . . . . . . . . . . . . .21
Setting Sampling rate and number of digits . . . . . . .22
Troubleshooting . . . . . . . . . . . . . . . . . . . . .23
Table of Contents

4
Display Features
16×4 Character LCD
Active Channel Number
Peak Value
Tracking Value
Valley Value
Sampling Rate
1
2
3
4
5
6
IPM650
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
1
+2.00001 Peak
+2.00000 mV/V
+1.99999 Valley
01 Gross 5 SPS
4
5
6
3
2
The Units button can change between
similar units.
Hold will flash on the LCD when active.
Shunt will be displayed on the LCD
when active.
The Tare function can be used to zero
out a sensor’s no load state, or to
account for a fixture.
TIPS FOR DISPLAY AND KEY FUNCTIONS

5
Buttons
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset
Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Channel
Enter
Reset
Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
Displays Channel Information
IN MENU MODE: Enter
Toggles between engineering units (force,
torque, pressure, and displacement) and the
standard mV/V.
IN MENU MODE: ▶Arrow
Toggles between displaying the tare and gross
values. Used to remove any fixture weights.
IN MENU MODE: ▲Arrow
Performs a shunt action using internal resistor
IN MENU MODE: Exit
Resets peak/valley
IN MENU MODE: ◀Arrow
ON/OFF
IN MENU MODE: ON/OFF
Start navigation
IN MENU MODE: n/a
Changes display to show peak, tracking,
valley, or all values
IN MENU MODE: Back
Freezes the current reading. HOLD will appear
on the LCD when active. Pressing any key on
the keypad will cancel the hold command.
IN MENU MODE: ▼Arrow

6
IPM650
Channel
Enter
Reset Menu
Track/Hold
Tare/Gross
Unit
Power
Exit
Shunt
Display
Back
A1
B1 C1
D1
A2
B2 C2
D2
A3
B3 C3
D3
A4
B4 C4
D4
A5
B5
A6
B6
A7 A8
Amplified Input (page 7)
Strain Gauge Input
(page 7) Relays
(page 8)
Analog Output
(page 8)
Power
Adapter USB
Compatible with
USB 2.0 only
CONNECTION TIPS
The +/– Excitation and +/– Signal
connections are used with mV/V output
sensors with the
+/– Excitation used to supply
power to the sensor.
The 24V output supply can be used to
power amplified sensors, such as our
amplified Rotary Torque sensors (for
instance the TRS605).
View online wiring code here:
http://www.futek.com/wirecode.aspx
Connector Pin Configuration

7
Wiring Layout
STRAIN GAUGE INPUT
PIN SYMBOL DESCRIPTION
B1 G Ground/Shield
B2 TEDS TEDS Data
B3 –S –Signal
B4 +S +Signal
B5 –E –Excitation
B6 +E +Excitation
AMPLIFIED INPUT
PIN SYMBOL DESCRIPTION
A1 G Ground/Shield
A2 G Ground/Shield
A3 24V OUT 24VDC Output
A4 5V OUT 5VDC Output
A5 –V –V and –mA Amplified Input Connections
A6 +V +V and +mA Amplified Input Connections
A7 PLEAD n/a
A8 PLAG n/a
Note: Shield should only be connected on either sensor side or instrument side. If connected on instrument side use follow-
ing directions. Connect shield to pin A1 or pin A2 of Amplified Input if sensor is amplified. Connect shield to pin B1 of Strain
Gauge Input if sensor is strain gauge.

8
RELAYS
PIN SYMBOL DESCRIPTION
C1 –R2 Solid State Relay 2 (–)
C2 +R2 Solid State Relay 2 (+)
C3 –R1 Solid State Relay 1 (–)
C4 +R1 Solid State Relay 1 (+)
ANALOG OUTPUT
PIN SYMBOL DESCRIPTION
D1 –VOUT Voltage Output (–)
D2 +VOUT Voltage Output (+)
D3 G Ground (current)
D4 IOUT Current Output
Ground (G) connections can be used to
connect a cable shield.
Strain Gauge Input is for sensors with a
mV/V output level.
Green screw terminals can be
removed to allow easy access to
connect the wires.
TIPS FOR WIRING
Wiring Layout (continued)
IPM650 Wiring Connection Examples: http://www.
futek.com/files/Pdf/Manuals_and_Technical_
Documents/IPM650Wiring.pdf

9
The IPM650 can store up to 15 profiles with channel 2 through 15 being user selectable.
1. Menu
2. Sensor Profile
3. New Channel
4. Set channel using left and right
arrow keys followed by Enter
5. Sensor Config and choose sensor
output type
6. Direction
7. Unit Selection
8. Sensor Capacity
9. Sensitivity (+)
10. Sensitivity (–) if applicable
11. Serial Number, (Serial number on
sensor)
12. Back to go back one menu
13. Save Changes
14. Back to exit Main Menu and put the
IPM650 into normal reading display
Profile Quick Setup (Calibration)

10
The decimal point can be moved by selecting it first and
turning it into a number, and then selecting another
digit to change it into a decimal point.
Sensitivity (+) must be entered. If only one direction is
selected, then sensitivity (+) will be applied to both directions
of output or negative direction output.
Sensitivity is the sensor’s output level, such as mV/V output,
and is found on the calibration certificate.
Pressing back without saving will prompt to exit without
saving. Enter can be used for Yes, and Back for No.
Current profiles cannot be set up manually and must be set up
using the Live Calibration feature in the profile setup.
Full bridge sensor type is for mV/V output sensors. Voltage
output and current output are for amplified inputs to the
IPM650.
Online sensor calibration data may be available by sensor
serial number at http://www.futek.com/CalibrationData.aspx
to assist in finding your sensor’s output or sensitivity.
TIPS FOR SETTING UP A PROFILE
A full profile setup guide can be found on our
FUTEK website at: http://www.futek.com/files/
Pdf/QuickStartGuide/IPM650ProfileSetup.pdf
Autres manuels pour IPM650
1
Table des matières
Autres manuels Futek Moniteur


















