Furngully GROVE BL-4 Guide de configuration
Includes Add-ons A1 | A2 | A5 | A6 | A7
GROVE120 DEGREE
WORKSTATION
BL–4
*General Guide | See MasterPlan
BL–1 – GROVE120 Degree Workstation............................................... 1
GROVE120 Degree Pod of 6 ..................................................................11
Add-Ons
A1 – GROVECable Tray (Leg Mounted).............................................. 3
A2 – Surface Mounted Dividers ............................................................ 7
A6 – Laminate Surface-Height End Panel ........................................15
A7 – Laminate Divider-Height End Panel ......................................... 17
A8 – Steel Inset End Panels ...................................................................19
EDITION CODE
120 DEGREE
GROVE
QTY PRODUCT CODE
3 BL48
6 BLPB1
3KIT-120
Includes: 120 Degree post leg and triangle box
3 Main Surface
PARTS LIST
120 DEGREE
GROVE
Place the triangle box on the post leg and secure with 4 bolts.
Next, attach the corner protector on corner that will be facing
toward user when desk is in use.
Insert the beam tabs into the leg brackets. Guide the beam tabs
into the bracket holes, there should be no gap between the beam
and legs. Using a rubber mallet, hammer the beam to lock in place.
1 |ASSEMBLE 120 DEGREE POST LEG
2 |CONNECT END LEGS, POST LEGS AND BEAMS
120 DEGREE
GROVE
1
3 |BOLT DOWN BEAM-TO-LEG LOCK PLATES
4 |MEASURE TO APPROXIMATE LEG SPACING
15”
15”1 5”
31”
31”
31”
31” 31”
31”
120 DEGREE
GROVE
Place and secure beam lock plates, be sure there is no gap
between the beam and the leg or plates will not fit.
Insert the screw through the overlapping beam slots and into the
black plastic piece. Slightly tighten the screw but DO NOT fully
tighten.
2
CABLE TRAY BL–4 | A1
PARTS LIST
IF WORKSTATIONS HAVE POWER, REFER TO BL-8 GROVEPOWER
GUIDE
QTY PRODUCT CODE
1 BCTLM (set of 2)
1 BTEC or BNTEC (set of 2) *if applicable
1120 Leg Bracket
3
2 |INSERT BEAM LOCK
Adjust Grovecable tray to approximate width of surface. Insert
the screw through the overlapping beam slots and into the black
plastic piece. Slightly tighten the screw with only a few turns. DO
NOT fully tighten.
1 | ATTACH CABLE TRAY HANGERS AND END CAPS*
Align slots on the cable tray and secure with 2 bolts from the
bottom. These hangers will mount to a Groveworkstation. Insert
Beam Grommet Covers.
*NOTE: End Caps (BTEC) are optional, follow the same install process with or without end caps.
CABLE TRAY
OPTIONAL
4
3 |LEG MOUNT CABLE TRAY
Insert tabs of connector bracket into the triangle post leg lots, then
use 2 screws to connect the cable tray hanger to bracket. Secure
other end of tray directly to Groveend leg using 2 screws. Tighten
beam lock.
CABLE TRAY
OPTIONAL
5
THESE MEASUREMENTS MAY VARY SLIGHTLY DUE TO PRODUCTION
TOLERANCES.
X
X
15/8”
Measure from the inner surface of the leg bracket to the outer edge
of the surface.
Option 1: If you are installing dividers or monitor arms leave a 1 5/
8”
space between surfaces, full width should be 21 7
/
8”
Option 2: If you are not installing dividers or monitor arms leave a
0” space between surfaces, full width should be 21 1/16”
5 |SURFACE INSTALLATION
120 DEGREE
GROVE
6
120 DEGREE
GROVE
6 |SECURE FIRST SURFACE
Position the surface on the desk frame. Align the outer side of the
surface flush and parallel with the outer side of the end leg. Insert
wood screws into the leg brackets and secure to the underside of
the surface.
7 |PLACE AND SECURE FIRST DIVIDER
Clamp bracket to the surface's right edge and tighten the vertical
bolt against the surface to secure the bracket. Repeat for all
brackets.
Lower screen into brackets and tighten horizontal bolt to clamp the
brackets onto the screens.
7
Table des matières
Autres manuels Furngully Ordinateur de bureau
