FULGOR WMT7010 Manuel utilisateur
1. SAFETY WARNING
2. PARTS IDENTIFICATION
3. ACCESSORIES
4. CONTROL PANEL
5. SPECIFICATIONS
6. INSTALLATION
7. DETERGENT CONTAINER
8. PROGRAMS
9. OPERATION
10. MAINTENANCE
11. TROUBLE SHOOTING
12. ELECTRICAL G DIAGRAM
1
2
2
3
3
4
8
9
10
14
15
16
INSTRUCTION MANUAL
Please read instructions carefully before using
FULLY AUTOMATIC WASHING MACHINE
FUZZY LOGIC CONTROL
Model: WMT7010
CONTENTS
www.fulgor.com.au
-1-
SAFETY WARNING
Never use water above
60℃.
Do not let children to play
with the machine.
Do not only hold the cord
while pulling out the plug.
Do not put hands into the
rotating tub.
70 C
Do not clean the body of
washer with volatile solvent
such as petrol and methane.
Also, do not pour these
solvents into the tub for
washing or drying purposes.
0.5
0.8 0.2
Make sure the lid is closed
especially during spin.
Don ' t s w i tch on the
p o w e r i f t h e w a t e r
pressure is lower than
0.05MPa a n d higher
than 0.5MPa.
WARNING! WARNING!
NOTE!
WARNING!
WARNING!
NOTE!
NOTE! NOTE!
K e e p t h e w a s h i n g
machine away from fire or
heat source.
Do not place the washing
machine in a damp place
and do not pour water onto
the control panel.
Do not expose washing
m a c h i n e t o d i r e c t
sunlight or rain.
The highest point of the
drain hose must be in the
height of 0.7m~1.2m above
floor level.
Never use the plug as
shown.
PARTS IDENTIFICATION
ACCESSORIES
-2-
(Please turn off the
tab after using)
Inlet hose
Lint filter
Pulsator
Power cord
Drain hose
Detergent box
Softener dispenser
Inner tub
Control panel
Base
Noise and mice-proof
plate
(It is inserted into the
base to reduce noise
and keep the mice
away.)
Magic lint filter
Adjustable foot Nut
Note:
The washing machine is to be connected to the water mains using new hose-sets supplied with the
appliance are to be used and old hose-sets should not be re-used.
2PC 1PC
(2set screws)
Inlet hose Noise and mice-
proof plate
UP
CONTROL PANEL
SPECIFICATIONS
Rated voltage Rated frequency
Rated input power
Rated water volume
220-240V~
50Hz
480W 144L
Net weight
7.0kg
569mmX583mmX957mm
38kg
Rated wash and spin
capacity
Dimension
Water pressure 0.05MPa-0.5MPa
-3-
957mm
583mm
569mm
0101
0909
0707
0505
0303
0202
1010
0808
0606
0404
PAUSE
START
POWERPOWER
12MIN12MIN
6 MIN6 MIN
9 MIN9 MIN
SOAKSOAK
11
22
33
1MIN1MIN
3MIN3MIN
5MIN5MIN
9MIN9MIN
WATER
LEVEL
WATER
LEVEL
WASHWASH RINSERINSE SPINSPIN
DELAY
PROGRAMPROGRAM
HOT
7
1.1 2.1 4.1 10
8.1
5.1
3.1
91 3 4 5 68
2
10
9
8
7
1
2.1
3
4
1.1
2
4.1
3.1 8.1
Water level button
Water level indicator
Water supply button
Water supply indicator
Wash button
Wash indicator
Rinse button
Rinse indicator
5
6
5.1 Spin button
Spin indicator
Delay button
Indicating window
Program button
Program indicator
Start/PAUSE button
Power button
FUZZY
COTTON
STRONG
GENTLE
SPEEDY
WOOL
ECONOMY
MINI
ANTI-CREASES
INNER TUB
CLEAN
WARM
COLD
WATERWATER
SUPPLY
-4-
Place the washing machine on a firm and level surface, use the level adjustment knob to regulate
the adjustable foot until the washing machine is stable.
1. Take out the noise-proof
plate.
2. The entrance is in the front
of the base.
3. Insert the noise-proof plate
into the base.
Insert the noise-proof plate into the washing machine base
Place the washing machine
at least 5cm away from the
wall.
Alternation of adjustable foot
4. Lay down the washing
machine, fasten the two
screws.
INSTALLATION
Place the washing machine
Use the adjustable foot to level the
machine with the floor:
1) Turn the nut clockwise to release the
screw adjuster on the foot.
2) Rotate the foot to raise or lower it
until it stands firmly on the ground.
3) Lock the foot in position by turning
the nut anti-clockwise until it comes
up against the bottom of the
machine.
Nut
Adjustable foot
1
2
3
Screw adjuster
INSTALLATION
Connection of the drain hose
Change the direction of the drain hose
Unfasten the fixed screw of
the drain hose joint.
Lead out the drain hose from
the opening to the other side.
Fasten up the screw to fix
the drain hose.
Insert the end of the drain hose into the hook shelf, and
hang the drain hose over a drain outlet (bath tub, sink,
etc.) or connect onto the special inlet point of the S trap.
Note: The highest point of the drain hose must be
between height of 0.7m~1.2m above floor level,
otherwise, the washer can not work normally.
Connection of the drain hose
-5-
0.7m~1.2m
Water Temperature
Cold :
Recommended cold water temperature is 10~24℃.
Hot :
Recommended hot water temperature is 50~60℃.
Warm:
Mixture of hot and cold water. (Warm water temperature is dependent upon the water
temperature and the pressure of both the hot and cold water supply lines.)
IMPORTANT:
Owner should turn off water supply whenever there will be an extended period of non-use.
Water Pressure
Do not operate the washer when the water pressure is lower than 0.05MPa or higher than
0.5MPa() to avoid damage of the inlet system.
Water supply requirements
-6-
INSTALLATION
Connection of the inlet hose
Faucet:
Installation and connection of the Inlet hose
The faucet must be with G3/4" standard screw thread. If not , it is
impossible to connect the inlet hose properly.
NOTE: water supply faucets should be readily accessible to
permit turning them off when washer is not being used.
Refer to Section on Water Supply Requirements before connecting water inlet
hoses.
1. Connect the water inlet hose to the connector by turning the connecting nut.
RUBBER RING
CONNECTING
NUT
Note:
The washing machine is to be connected to the water mains using new
hose-sets supplied with the appliance, old hose-sets should not be re-
used.
Ⅰ. About faucet
COLD
HOT
WATER INLET HOSE
COLD WATER
CONNECTOR
HOT WATER
CONNECTOR
CONNECTING
NUT
ELBOW
A: If you just have one water supply line (cold or hot water), connect the inlet hose to
the cold water connector. Do not unscrew the lid of hot water connector.
. About washing machine
To prevent water leakage, please ensure the connecting nut is tightened
securely. If water leakage, check the nut whether it is filled with rubber ring.
RUBBER RING
IMPORTANT:
In this situation you can not set wash temperature to WARM OR HOT.
LID OF HOT WATER
CONNECTOR
-7-
INSTALLATION
Connection of the power cord
DETERGENT CONTAINER
Compositive detergent and softener for laundry
Draw out the detergent box.
1
2
4
Add the suitable quantity detergent into the
detergent dispenser.
Dilute concentrated softener with triplicate water.
If softener needed, do not open the wash lid when spin, or else the softener will be premature
used and the effect will be worse.
3Add the suitable quantity softener into the
softener dispenser before wash.
Note:
Push detergent box into completely.
Water
level
Detergent dosage
Low
Mid
High
Slight dirty Dirty
12-20g
18-33g
27-36g 48-70g
35-56g
25-38g
Warning:
The socket should have assembled the 5A fuse.
Use the socket which can be connected ground wire.
Note:
The ground wire of the washing machine is set in the plug, don't
try to modify it.
The socket should have reliable ground wire. If no ground wire in
socket, please call the technician to assemble.
Never try to connect the ground wire of the washing machine
together with that of gas pipe or water pipe, telephone cord or
lightening rod.
Do not use the damaged cord because it could cause electrical
leakage and fire.
In case cord is damaged, call the local Service Company to change it.
Softener for laundry
Water
level
Softener dosage
1-2
Normal
14
Concentrated
3-4
5-6
7-8
9-10
20
25
30
36
5
7
10
13
16
Inject softener into the softener dispenser before
washing, At the last time for rinse, the softener
will be infused into the rinsing automatically.
Dilute concentrated softener with triplicate
water.
If softener needed, do not open the wash lid
when spinning, or else the softener will be
prematurely used and the effect will be awful.
Note:
-8-
DETERGENT CONTAINER
Program
Washing program form
Microcomputer controlled board assembly saved up 7 kinds of washing programs,
please refer to the following washing program form.
Note: 1.The total operating time may vary according to water volume, tolerance is permitted.
2.In case the unbalance of laundry trigger the safety switch into action when spinning,
the machine will automatically refill water to adjust the balance.
12
24
25
FUNCTION
SOAK
(MIN)
WASH
(MIN)
RINSE
(CYCLE)
SPIN
(MIN)
PROGRAM
1
20 1
3
5
1
12
1
3
2
6
1
6
Select the time according to the quantity and quality of the wash laundry itself.
2
WOOL
FUZZY
COTTON
STRONG
GENTLE
SPEEDY
ECONOMY
MINI
ANTI-CREASES
TUB CLEAN 30
12 2
3
2
2
1
PROGRAM
4.I
hose into the hook shelf, and
hang the drain hose over a
drain outlet.
nsert the end of the drain
0.7m~1.2m
OPERATION
-9-
POWERPOWER
Operation
Step one: Switch on the power supply.
5.Put suitable wash load
into the inner tub.
6.Add suitable detergent
according to the wash
load volume into the box
of powder laundry
detergent .
7.Close wash lid completely.
(or else, it will not to spin and
will sound alarm.)
switched on, and it will shut down itself at once when the program finished.
Step two: Choose w
You can choose the optimization program or edit the program yourself
and also combine the program as you need.
ash programs.
FUZZY COTTON STRONG GENTLE SPEEDY
WOOL
ECONOMYMINI
ANTI-CREASES
INNER TUB
CLEAN
PROGRAMPROGRAM
Preparation
1.
2.
Connect the water inlet
hose to the water faucet.
Turn on the water faucet.
3.Plug in the power supply
cord.
Press the POWER button, the indicator will glow, it means that the machine is in
auto-enter fuzzy program.
The fuzzy program can select the suitable water level and program itself according to the
quantity and material of the clothes you put into the machine.
If you press the start button, the machine will run the fuzzy program at once, if you don't
want to use the fuzzy program, follow next step.
A: Choose the optimization program.
Press the "PROGRAM" button to Choose the desired function and then the corresponding
indicator will blink.
Note: Press the "PROGRAM" button continuously all options of water flow will circulate as
figure.
Table des matières
