Fujitsu SCENIC 800 Manuel utilisateur

A26361-K516-Z100-1-7619 1

Introduction

This Operating Manual tells you how to put your PC into operation and how to operate it in daily use.

This description applies for all configuration levels. Depending on the configuration level chosen

some of the hardware components described may not be available on your PC. Please observe the

notes on your operating system.

Your device is a powerful PC which is suitable for both professional and private use.

Your PC is available in various configuration levels, which differ in hardware and software

equipment. In addition, you can incorporate operable drives (for example DAT drive, streamer) and

a second hard disk, as well as other boards.

Depending on the configuration level chosen, your PC is supplied with Windows 9x or Windows NT

as the operating system.

Your PC has a number of security features to ensure that no unauthorized persons can access your

data. For example, you can activate a screen saver with password protection. The security functions

in the BIOS Setup also allow you to protect your data by means of passwords. In addition, you can

also lock your PC mechanically using the cover lock. Systems with a chipcard reader offer additional

protection.

Further information on this PC is provided:

• in the manual "Safety, Guarantee and Ergonomics"

• in the Operating Manual for the monitor

• in the Technical Manual for the system board

• in the manual "BIOS Setup"

• in the documentation of your operating system

• in the information files (e. g. *.TXT, *.DOC,*.WRI, *.HLP)

iSome of the manuals listed can be found on the CD "Drivers & Utilities" provided with your

computer. These manuals can be read and printed with the Acrobat Reader contained on

the CD.

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

!Pay particular attention to texts marked with this symbol. Failure to observe this warning

endangers your life, destroys the system, or may lead to loss of data.

iThis symbol is followed by supplementary information, remarks and tips.

Texts which follow this symbol describe activities that must be performed in the order shown.

Texts in this typeface are screen outputs.

Texts in italics indicate commands or menu items.

"Quotation marks" indicate names of chapters and terms that are being emphasized.

A26361-K516-Z100-1-7619 3

Important notes

In this chapter you will find information regarding safety which it is essential to take note of when

working with your PC. The manufacturer's notes contain helpful information on your PC.

Safety

!Pay attention to the information provided in the manual "Safety, Guarantee and

Ergonomics" and to the following notes.

• During installation and before operating the device, observe the instructions on environmental

conditions in the chapter entitled "Technical data" as well as the instructions in the chapter

"Preparation for use and operation".

• Please check whether the device is set to the local power supply (see chapter "Preparation for

use and operation").

• The main switch and the ON/OFF switch do not disconnect the system unit from the line

voltage. To disconnect the line voltage completely, remove the power plug from the grounded

power outlet.

• Replace the lithium battery on the system board in accordance with the instructions in the

chapter "System expansions - Replacing processor and lithium battery".

• Caution: components in the system can get very hot.

• Keep this Operating Manual together with your device. If you pass on the device to third

parties, you should also pass on this manual.

Notes on installing and removing boards

Boards with electrostatic sensitive devices (ESD) may be identified by the

label shown.

When you handle boards fitted with ESDs, you must observe the following

points under all circumstances:

• You must always discharge yourself (e.g. by touching a grounded

object) before working.

• The equipment and tools you use must be free of static charges.

• Pull out the power plug before inserting or pulling out boards containing

ESDs.

• Always hold boards with ESDs by their edges.

• Never touch pins or conductors on boards fitted with ESDs.

Important notes Manufacturer's notes

4A26361-K516-Z100-1-7619

Manufacturer's notes

Energy saving

When the PC is delivered, some energy-saving functions are already set (see the Technical Manual

for the system board or the manual "BIOS Setup").

• If you are not using your PC, switch it off.

• In the BIOS Setup you may set further energy-saving functions for the PC (see the Technical

Manual of the system board or in the manual "BIOS Setup").

Energy saving under Windows NT

If the attached monitor and screen controller support power management in accordance with VESA

(DPMS), the screen saver Powersaver ("Drivers & Utilities" CD) can be used to switch the monitor

into power management mode.

Energy saving under Windows 95

The Screen Saver tab allows you to set further energy-saving functions for your screen. Select the

following item in the Start menu: Settings - Control Panel - Display - Display Properties - Screen Saver -

Energy saving features of monitor.

Energy saving under Windows 98

In the Start - Settings - Control Panel - Power Management menu you can set additional power-

management functions.

Manufacturer's notes Important notes

A26361-K516-Z100-1-7619 5

Disposal and recycling

This device has been manufactured to the greatest possible degree from materials which can be

recycled or disposed of in a manner that is not environmentally damaging. The device is taken back

after use, so that it can be recycled, provided that it is returned in a condition which is the result of

normal use. Any components not recuperated will be disposed of in an environmentally acceptable

manner.

For devices marked with this symbol Siemens AG offers a guarantee for

36 months with a Bring-in-Service. The guarantee starts on the day of

delivery (sale date) by Siemens or a Siemens partner.

We herewith declare that it will be possible to repair any device marked with

the eco-label for at least 5 years after production of that device has

discontinued.

Information on power management and energy saving mode can be found in

chapter "Technical data".

Do not throw lithium batteries or accumulators into the trashcan. They must be disposed of in

accordance with local regulations concerning special waste.

If you have any questions on disposal, please contact your local office, our service department, or,

directly:

Siemens AG

Recyclingcenter

D-33106 Paderborn

Tel.: 49 5251 818 010

Fax: 49 5251 818 015

CE certificate

The shipped version of this device complies with the requirements of the EEC directives

89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".

Important notes Manufacturer's notes

6A26361-K516-Z100-1-7619

FCC Class B Compliance Statement

If there is an FCC statement on the device, then:

The following statement applies to the products covered in this manual, unless otherwise specified

herein. The statement for other products will appear in the accompanying documentation.

NOTE:

This equipment has been tested and found to comply with the limits for a "Class B" digital device,

pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-

Causing Equipment Regulations. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in strict accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Siemens AG is not responsible for any radio or television interference caused by unauthorized

modifications of this equipment or the substitution or attachment of connecting cables and

equipment other than those specified by Siemens AG. The correction of interferences caused by

such unauthorized modification, substitution or attachment will be the responsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to any and all optional

peripheral or host devices. Failure to do so may violate FCC rules.

Manufacturer's notes Important notes

A26361-K516-Z100-1-7619 7

Power cord selection

The power cord for this unit has been packed separately and has been selected according to the

country of destination. It must be used to prevent electric shock. Use the following guidelines if it is

necessary to replace the original cord set.

The female receptacle of the cord set must meet

IEC 320 requirements.

For the United States and Canada

Use a UL listed and CSA labeled cord set consisting of a two conductor cord with a maximum length

of 15 feet.

For units which stand on a desk or table, type SVT or SJT cord sets shall be used.

For units which stand on floor, only SJT type cord sets shall be used.

The cord set must be selected according to the current rating for your unit. Please consult Table A

for the selection criteria for power cords used in the United States and Canada.

Table A:

Cord Type Size of Conductors

in Cord Maximum Current

Rating of Unit

SJT 18 AWG

16 AWG

14 AWG

10 Amps

12 Amps

SVT 18 AWG

17 AWG 10 Amps

12 Amps

For units set at 115 V

Use a parallel blade attachment plug rated 15 A,

125 V.

For units set at 230 V (outside of the United States and Canada)

Use a cord set consisting of a minimum AWG according to Table A and an attachment plug rated

15 A, 250 V. The cord set should have the appropriate safety approvals for the country in which the

equipment will be installed and should be marked HAR.

Important notes Transporting the PC

8A26361-K516-Z100-1-7619

Transporting the PC

!Transport all parts separately, and in their original packaging or in a packaging which

protects them from knocks and jolts, to the new site. Do not unpack them until all transport

maneuvers are completed.

Never drop the monitor (risk of implosion)!

Cleaning the PC

!Turn off all power and equipment switches and pull the power plug out of the grounded

power outlets.

Do not clean any interior parts yourself, leave this job to a service technician.

Do not use any cleaning agents that contain abrasives or may corrode plastic.

Ensure that no liquid enters the system.

Ensure that the ventilation areas of the system unit and the monitor are free.

Cleaning the system unit and the monitor

Wipe the system unit and monitor casing with a dry cloth. If particularly dirty, use a cloth which has

been moistened in mild domestic detergent and then carefully wrung out.

Cleaning the keyboard and the mouse

Use a cloth for disinfection to clean the keyboard and the mouse.

Remove the retaining ring on the underside of the mouse and then clean the mouse mechanism and

the rotating ball.

Using both thumbs exert downward pressure on the notches of the retaining ring and turn the

ring anticlockwise (1).

Remove the retaining ring and the rotating ball from the mouse (2).

Clean the three small wheels in the mouse and the ball with a lint-free cloth.

Replace the ball and the retaining ring (3).

Using both thumbs exert downward pressure on the notches of the retaining ring (4) and turn

the ring clockwise. You must feel the ring engage.

A26361-K516-Z100-1-7619 9

Preparation for use and operation

!Please take note of the safety information in the chapter "Important notes".

Unpacking and checking the delivery

It is recommended not to throw away the original packaging material! It may be required for

reshipment at some later date.

Unpack all the individual parts.

Check the delivery for damage incurred during transport.

Check whether the delivery agrees with the details in the delivery note.

Should you discover that the delivery does not correspond to the delivery note, notify your local

sales office immediately.

iIf you have received drives or boards with your PC, please do not install them until after

first-time setup. How to install drives and boards is described in the chapter "System

expansions".

Preparing the PC for use

First-time setup includes the connection of the devices (monitor, mouse, keyboard etc.) and the

setup of the supplied software.

When you set up the PC for the first time, you should carry out the following steps in the order

shown:

1. Decide where you are going to use the PC.

2. Connect the external devices to the system unit.

3. Check the rated voltage of the system unit and connect it to the line voltage.

4. Switch the PC on and follow the instructions on the screen.

Preparation for use and operation Setting up the PC

10 A26361-K516-Z100-1-7619

Setting up the PC

!When installing your PC, give consideration to the recommendations and safety notes in

the manual "Safety, Guarantee and Ergonomics".

Set up the PC only in its correct orientation. The points to observe are illustrated on the

following pages.

We recommend that you place your equipment on a surface with good anti-slip qualities.

In view of the multitude of different finishes and varnishes used on furniture, it is possible

that the rubber feet of the devices will mark the surface they stand on.

Do not expose the PC to extreme environmental conditions (see chapter "Technical

data"). Protect it from dust, humidity and heat.

Provide at least 200 mm of clearance on the left, in front of and behind the ventilator area

of the system unit to ensure adequate ventilation. Do not cover the ventilation areas of the

monitor and the fan.

Do not place several system units one above the other.

Connecting devices

!The power plug must be disconnected!

Read the documentation on the external device before connecting it.

Do not connect or disconnect cables during a thunderstorm.

Always take hold of the actual plug body. Never unplug a cable by pulling the cable itself!

Connect and disconnect the cables in the order described below.

Connecting cables

• Turn off all power and equipment switches.

• Unplug all power plugs from the grounded power outlets.

• Connect all cables at the system unit and peripherals. You must observe the information

provided in the chapter "Important notes".

• Plug all data communication cables into the utility sockets.

• Plug all power cables into the grounded power outlets.

Disconnecting cables

• Turn off all power and equipment switches.

• Unplug all power plugs from the grounded power outlets.

• Unplug all data communication cables from the utility sockets.

• Disconnect all cables from the system unit and peripherals.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Ordinateur de bureau

Fujitsu

Fujitsu CELSIUS M770 Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO D7 Series Manuel utilisateur

Fujitsu

Fujitsu CELSIUS W530 Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO D5 Series Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO D53 Series Manuel utilisateur

Fujitsu

Fujitsu DESKPOWER 5000 Series Manuel utilisateur

Fujitsu

Fujitsu DESKPOWER C600 Series Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO P372 Series Manuel utilisateur

Fujitsu

Fujitsu Stylistic ST6000 Series Manuel utilisateur

Fujitsu

Fujitsu CELSIUS C620 Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO Q5020 Manuel utilisateur

Fujitsu

Fujitsu DESKPOWER P321 Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO Q7010 Manuel utilisateur

Fujitsu

Fujitsu Supercomputer PRIMEHPC FX700 Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO P4 Series Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO X956 Manuel utilisateur

Fujitsu

Fujitsu Siemens CELSIUS 4 Series Manuel utilisateur

Fujitsu

Fujitsu DESKPOWER 6000 Series Manuel utilisateur

Fujitsu

Fujitsu CELSIUS W370 E85+ Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO P5635 Manuel utilisateur

Fujitsu

Fujitsu Esprimo E5 Series Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO K55x/24 Series Manuel utilisateur

Fujitsu

Fujitsu ESPRIMO E Manuel utilisateur

Fujitsu

Fujitsu CELSIUS R920 Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur