Fujitsu F2MC Series Manuel utilisateur
FUJITSU SEMICONDUCTOR
CONTROLLER MANUAL
F2MC FAMILY
PARALLEL COMMUNICATIONS ADAPTER
MB2142-03
USER’S MANUAL
CM41-00413-1E
PREFACE
■Objectives and intended readership
The MB2142-03 support tool (parallel communications adapter) is designed to enable the
development and evaluation of products based on the F2MC* family.
The MB2142-03 is connected to the main unit (MB2141).
This enables the main unit to perform parallel communication with the host machine (such as a
personal computer).
This manual describes the handling and connection of the MB2142-03. It is aimed at engineers
responsible for the development of products based on the F2MC, using the MB2142-03.
Refer to the following related manual as necessary:
• Related manual
2140 Main Unit MB2141 Emulator User’s Manual
*: F2MC stands for FUJITSU Flexible Microcontroller.
■Configuration of this manual
This manual consists of the following two chapters. Familiarize yourself with the contents of this
manual before attempting to use the adapter.
Chapter 1 Handling and Specifications of the Product
Describes the handling and specifications of the parallel communications adapter.
Chapter 2 Connections
Describes the connections and the power-on and power-off sequences of the parallel
communications adapter.
1995 FUJITSU LIMITED Printed in Japan
1. The products described in this manual and the specifications thereof may be changed without prior
notice. To obtain up-to-date information and/or specifications, contact your Fujitsu sales
representative or Fujitsu authorized dealer.
2. Fujitsu will not be liable for infringement of copyright, industrial property right, or other rights of a third
party caused by the use of information or drawings described in this manual.
3. The contents of this manual may not be transferred or copied without the express permission of
Fujitsu.
4. Some of the products described in this manual may be strategic materials (or special technology) as
defined by the Foreign Exchange and Foreign Trade Control Law. In such cases, the products or
portions thereof must not be exported without permission as defined under the Law.
READING THIS MANUAL
■Page layout
In this manual, an entire section or subsection is presented on a single page or spread
whenever possible. The reader can thus view a section without having to flip pages. The
contents of each section/subsection are summarized immediately below the title. You can obtain
a rough overview of the parallel communications adapter (MB2142-03) by reading through these
summaries. The spread layout of this manual is described below.
■Spread layout
Section title Section or subsection summary
Subheading Figure and table titles
Subsection title
i
CONTENTS
CHAPTER 1 HANDLING AND SPECIFICATIONS OF THE PRODUCT .................................................1
1.1 Packing List.........................................................................................................................................2
1.2 Parallel Communications Adapter Specifications................................................................................4
1.2.1 Electrical characteristics of I/O signal lines............................................................................. 5
1.2.2 Connector pin assignment ...................................................................................................... 6
1.3 IF Cable Specifications........................................................................................................................8
1.4 Notes on Use.....................................................................................................................................10
CHAPTER 2 CONNECTIONS .................................................................................................................11
2.1 System Configuration........................................................................................................................12
2.2 Connection to Main Unit....................................................................................................................14
2.3 Connection to Host Machine.............................................................................................................16
2.4 Power-on Sequence..........................................................................................................................18
2.5 Power-off Sequence..........................................................................................................................19
ii
FIGURES
TABLES
Figure 1.1 Parallel communications adapter ............................................................................................ 3
Figure 1.2.1 Electrical characteristics of I/O signal lines ............................................................................. 5
Figure 1.2.2 Parallel communications connector pin assignment ............................................................... 6
Figure 1.3 IF cable dimensions ................................................................................................................ 9
Figure 2.1 System configuration ............................................................................................................ 12
Figure 2.2 IF cable connection ............................................................................................................... 15
Figure 2.3 Printer cable connection ....................................................................................................... 17
Table 1.2 Parallel communications adapter specifications...................................................................... 4
Table 1.2.2 Parallel communications connector signal line names ........................................................... 7
Table 1.3a IF cable components .............................................................................................................. 8
Table 1.3b IF cable general specifications ............................................................................................... 8
Table 1.4 Storage environment ............................................................................................................ 10
1
CHAPTER 1 HANDLING AND SPECIFICATIONS OF
THE PRODUCT
This chapter explains the handling and specifications of the parallel communications
adapter. Read this chapter and check the contents of the package before attempting to
use the parallel communications adapter.
1.1 Packing List
1.2 Parallel Communications Adapter Specifications
1.2.1 Electrical characteristics of I/O signal lines
1.2.2 Connector pin assignment
1.3 IF Cable Specifications
1.4 Notes on Use
2
1.1 Packing List
Before first using the parallel communications adapter, check that the package
contains the following components:
• Parallel communications adapter × 1
• IF cable ×1
■Appearance and names of parts
Figure 1.1 illustrates the parallel communications adapter. For details of the connections, see
Chapter 2, “Connections.”
The function of each part is described below:
IF connector: Used to connect the IF cable.
Parallel communications connector: Used to connect the printer cable.
Obtain a printer cable that is suitable for the host machine (such as a personal computer).
3
Figure 1.1 Parallel communications adapter
Parallel communications connector
PARALLEL
PARALLEL
COMMUNICATION
ADAPTOR
COM PORT
IF connector
4
1.2 Parallel Communications Adapter Specifications
Table 1.2 lists the specifications of the parallel communications adapter.
■Parallel communications adapter specifications
Table 1.2 lists the specifications of the parallel communications adapter.
*1: Power is supplied from the main unit.
*2: Not including projections.
■Parallel communications specifications
The parallel communications format conforms to the Centronics interface.
An Amphenol 36P connector is used as the parallel communications connector.
The electrical characteristics of the I/O signal lines are described in Section 1.2.1.
Table 1.2 Parallel communications adapter specifications
Item Contents
Name Parallel communications adaptor
Model MB2142-03
Power supply Voltage: +5 V ±5% Current: 1A (max.) *1
Operating
temperature 0 to +55oC
Operating
humidity 30% to 80% (non-condensing)
Dimensions 120mm (W)×90mm (D) × 26mm (H) *2
Weight 200g approx.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fujitsu Adaptateur
Fujitsu
Fujitsu FMW43VA01 Manuel utilisateur
Fujitsu
Fujitsu MB91360 SERIES Manuel utilisateur
Fujitsu
Fujitsu MB2198-169-E Manuel utilisateur
Fujitsu
Fujitsu fi-5000N Manuel utilisateur
Fujitsu
Fujitsu PagePrinter Manuel utilisateur
Fujitsu
Fujitsu D3607 Manuel utilisateur
Fujitsu
Fujitsu UTY-TFSXH3 Manuel
Fujitsu
Fujitsu PRIMEQUEST 2000 Series Feuille d'instructions
Fujitsu
Fujitsu PGA-401P Manuel utilisateur
Fujitsu
Fujitsu MB2146-09B-E Manuel utilisateur
Fujitsu
Fujitsu Stylistic 3400 Manuel utilisateur
Fujitsu
Fujitsu FR Family FR60 Lite Manuel utilisateur
Fujitsu
Fujitsu MB2198-130 Manuel utilisateur
Fujitsu
Fujitsu MB2146-07-E Manuel utilisateur
Fujitsu
Fujitsu FPCAC14A Manuel utilisateur
Fujitsu
Fujitsu UTY-TFSXH3 Manuel de service
Fujitsu
Fujitsu FMW43VA1 Manuel utilisateur
Fujitsu
Fujitsu MB2146-09 Manuel utilisateur
Fujitsu
Fujitsu D2907 Manuel utilisateur
Fujitsu
Fujitsu UTY-TFSXW1 Manuel de service
