Fujikura CT110 Manuel utilisateur
1st
Advanced Optical Fiber Cleaver
CT110/111
Instruction Manual
Thank you for purchasing Fujikura’s Advanced
Optical Fiber Cleaver.
Please read this instruction manual carefully
before operating the equipment.
Adhere to all safety instructions and
warnings contained in this manual.
Keep this manual in a safe place.
There may be updates without notice.
Please consent beforehand.
The software equipped in the cleaver and its related documents
are protected by copyright laws and international treaty
provisions as well as other intellectual property laws.
Copying some or all of instruction manual without notice is
forbidden.
Moreover, without permission from our company, it cannot be
used on the Copyright Act except when used as an individual.㻌
㻌
Table of Contentsᴾ
Safety Information...........................................................1
General Information........................................................4
Introduction ......................................................................................................4
Components.....................................................................................................5
Description.......................................................................................................6
Cleaving Operation.........................................................9
Power Supply...................................................................................................9
How to Operate.............................................................................................. 11
Cleave Mode Selection ..................................................................................14
Adjusting the Total Fiber Length .....................................................................18
Using the Coating Adjuster.............................................................................21
Adjustment for Angled Cleaving (CT111 only) ................................................23
Settings.........................................................................25
Cleave Settings..............................................................................................25
Fiber Holder Registration (FH110 series only)................................................26
Other Settings ................................................................................................29
Blade Replacement........................................................................................30
Blade Adjustment ...........................................................................................32
Blade Position Change...................................................................................34
Cleave Count Display.....................................................................................35
LED Display Codes.......................................................36
Blade Position Display ...................................................................................36
Cleave Mode Display .....................................................................................37
Maintenace ...................................................................38
Cleaning the Cleaver......................................................................................38
Fiber Breakage Prevention.............................................................................39
Troubleshooting.............................................................40
Q & A .............................................................................................................40
Compliance...................................................................43
Warranty and Contact...................................................45
Warranty ........................................................................................................45
Contact Addresses .........................................................................................46
CT110/111_Rev1
11
Safety Information
Thank you for purchasing Fujikura’s Advanced Optical Fiber Cleaver
In this instruction manual, the processes and procedures are documented which should
be observed in order to use this product safely.
This cleaver has been designed for cleaving glass optical fibers. Cleaving should not be
attempted on anything other than a glass optical fiber with this product
Read and understand all safety
instructions.
Ask our service centers
for repair as soon as
possible.
Read this instruction manual carefully
before operating the machine.
Store this instruction manual in a safe
place.
The following symbols are used in this
instruction manual to indicate warning and
caution for safe use. Learn and
understand the meanings of these
symbols.
WARNING! / CAUTION!
There is a possibility of death, serious
injury, or physical loss if this indication is
ignored. Ignoring this indication is an
improper use of the machine.
PAY ATTENTION!
In general, a yellow triangle means the
associated caution should be observed.
Example:
PAY ATTENTION to hot surface!
DO NOT …!
Example:
DO NOT disassemble!
DO
A blue circle with a white graphic inside
means the associated process is required
for safe operation
Example:
You must disconnect the plug!
Follow all safety instructions
Stop using it when it malfunctions
Instruction Manual
CT110/111_Rev1
22
Safety Information
WARNING / CAUTION
Disconnect the AC power cord from the AC adapter plug or the wall outlet
immediately if a user observes the following:
• Fumes, bad smell, noise, or over-heat occurs.
• Liquid or foreign matter falls into this product.
• The Cleaver or AC adapter is damaged or dropped.
If any of these occur, contact our service center for repair. Leaving the
cleaver or AC adapter in a damaged state may cause equipment failure,
electric shock, or fire and may result in personal injury or death.
The AC adapter supplied with this product is the only adapter approved for
use with this product.
Using an improper AC power source may cause equipment damage,
fumes, electric shock, or fire and may result in personal injury or death.
Do not disassemble or modify the cleaver or the AC adapter in any way.
In particular, do not remove or bypass any electrical or mechanical device
(e.g. a fuse or safety switch) incorporated into the design and
manufacturing of this equipment. Modificatio
n could cause damage that
may result in electric shock, fire, personal injury, or death,.
Connect AC power cord properly to the AC Adapter and to the wall outlet.
When inserting the AC plug, make sure there is no dust or dirt on the
terminals. Insert the female plug into the AC
Adapter and the male plug
into the wall outlet until both plugs are fully seated. Incomplete
engagement may cause fuming, electric shock, equipment damage, or fire
and may result in personal injury or death.
Disconnect the AC power cord
when the cleaver is not being used.
Use the supplied AC power cord. Do not place heavy objects on the AC
power cord. Use of an improper or damaged cord may cause equipment
failure, electric shock, or fire and may result in personal injury or death.
Do not touch the cleaver, AC power cord and AC plugs with wet hands.
This may result in electric shock.
Do not operate the cleaver near hot objects, in hot environments, in dusty
/ humid environments, or when water condensation is present on the unit.
This may result in electric shock, cleaver malfunction, or poor cleaving
performance. When water condensation is present, leave the cleaver
powered off and allow to air-dry at room temperature for at least 24 hours.
CT110/111_Rev1
33
Safety Information
ᴾ
WARNING / CAUTION
Do not store the cleaver in any place where temperature and/or humidity are
extremely high. Such environments may cause damage to the cleaver.
Do not place the cleaver in an unstable or unbalanced position. The cleaver
may shift or lose balance, causing it to
fall. This may result in personal injury or
equipment damage.
The cleaver is a precisely adjusted and aligned instrument. Keep the unit away
from strong mechanical shock or impact. Failure to do so will result in
misalignent and lead to poor cleaving results. Use the supplied box for
transportation and storage. The box will protect the cleaver from damage,
moisture, vibration, and shock during storage and transportation.
Always set the cleaver blade to the correct position in the machine. Setting the
blade to an incorrect position may cause serious damage to the machine.
If the cleaver blade is replaced, only use the manufacturer-specified part.
Failure to do so will result in serious damage to the machine.
The cleaver requires no lubrication. Adding oil or grease may degrade the
cleaving performance and damage the cleaver.
This equipment must be repaired or adjusted by a qualified technician or
engineer. Incorrect repair may cause fire or electric shock. Please contact the
authorized distributor if any problems occur on the machine.
Keep the cleaver free of contaminants. They will degrade the cleave quality
and may cause the machine to malfunction.
Do not use the cleaver for anything other than cleaving optical
fibers. Using it
for any other purpose may damage the cleaver.
RECYCLING and DISPOSAL
In European Union
In accordance with the European Parliament Directive, electrical parts and materials
that can be re-used and/or recycled have been
identified in order that the use of new
resources and the amount of waste going for landfill can be minimised.
In the European Union, do not discard this product as unsorted municipal waste.
Contact your local authorities for further information.
In other countries
[Recycling]
To recycle this product, disassemble it first, sort each part separately by material
components and follow your local recycling regulations.
[Disposal]
This product can be disposed of same as the
standard electric poroducts. Follow your
local disposal regulations.
CT110/111_Rev1
4
General Information
Introduction
The CT110 / CT111 cleavers are designed for use with a single optical fiber.
To master the CT110 and CT111, read this instruction manual prior to use.
CT110
The CT110 model is applicable for cleaving fibers having a cladding diameter of up to
250m. This model does not have the angled cleaving unit.
CT111
The CT111 model is applicable for cleaving fibers having a cladding diameter of up to
250m. Angled cleaving is possible using the rotation base.
FH110, FH-100, and FH-70* series fiber holder options are available for the CT110/111.
*Additional accessories required
CT110/111_Rev1
5
General Information
Components
The contents of the standard package are shown; please confirm all items are included.
Standard Components
Name
Item
Amount
AC Adapter
ADC-21
1pc
AC Cord
ACC-**
1pc
USB Cable
USB-01
1pc
Quick Reference Guide
QRG-11-E
1pc
1.5mm Hex Wrench
HEX-01
1pc
2.5mm Hex Wrench
HEX-02
1pc
Cleave test report
CR-CT110
1pc
Warning and Cautions
WAC-06-E
1pc
Additional Options
Name
Item
Remarks
Cleaver Blade
CB-06A
Replacement blade
Fiber Holder Adapter Plate
AD-CT110-FH70
Fiber Holder Adapter for FH-70
Fiber Holder
FH110-***
Each Sizes
Advanced Fiber Cleaver
CT110
(without angle cleaving base)
CT111
(with angle cleaving base)
CT110/111_Rev1
6
General Information
Description
Clamp Unit
Fiber Holder Clamp
LED Indicators
Blade Unit
Rotary Base
CT111
Cleave Button
Top
CT110
Length Scale
Positioning Spacer
Coating Adjuster
CT110/111_Rev1
7
General Information
Left Lever
Right Lever
Fiber Clamp
Cleave Angle Adjustment Screw
(CT111 only)
USB Port
ON/OFF Switch
Holder Clamp
DC Power Port
Angle Scale
(CT111 only)
Function Keys
Battery Box Cover
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fujikura Outils
