FSK Rhino 232 Manuel utilisateur

CONTENTS

Getting Started ..................................................................................................................................... 4

Overview ...................................................................................................................................................................................................

Installation ..............................................................................................................................................................................................

Programming ........................................................................................................................................................................................

Rhino 232 Panel Overview ............................................................................................................. 5

Installation ...............................................................................................................................................

Mounting of the alarm panel .......................................................................................................................................................

Wiring the alarm panel ....................................................................................................................................................................

Power supply ..........................................................................................................................................................................................

Piezo Buzzers .........................................................................................................................................................................................

Sound bomb ..........................................................................................................................................................................................

Strobe lamp ............................................................................................................................................................................................

Wired zones ............................................................................................................................................................................................

Wiring .........................................................................................................................................................................................................

Wireless zones .......................................................................................................................................................................................

Programming .........................................................................................................................................

Entering the programming mode ............................................................................................................................................

Navigating the programming menus .....................................................................................................................................

Setting up zones ..................................................................................................................................................................................

Programming wireless zones ......................................................................................................................................................

Users ............................................................................................................................................................................................................

Area Options ..........................................................................................................................................................................................

Hardware options ...............................................................................................................................................................................

Keypad Options ...................................................................................................................................................................................

Outputs .....................................................................................................................................................................................................

Communications ................................................................................................................................................................................

Upload/Download (UDL) ................................................................................................................

Using the UDL ......................................................................................................................................................................................

Appendix A .............................................................................................................................................

Text Entry Mode ..................................................................................................................................................................................

Hex Entry Mode ...................................................................................................................................................................................

Warranty Information .......................................................................................................................

Zone Commissioning Process ..................................................................................................... 24

The Rhino 232 panel is a wireless alarm panel

The Rhino 232 panel is equipped with an onboard GSM modem which sends alarms to the

control room

The Rhino 232 panel works with the MiRhino mobile application which allows the user to

remotely control and monitor his or her alarm system

The Rhino 232 panel has been designed with ease-of-use, ease of installation and ease of

programming in mind

GETTING STARTED

1. Overview

2. Installation

Connect battery to the panel

Mount the panel in a location that has good GSM signal reception and that’s convenient

for the user

Wire the power supply to the alarm panel

Mount the sensors

Program the alarm panel

Perform the commissioning process

3. Programming

The keypad

The UDL (up/download) software supplied on the FSK DVD. The UDL programming can be

done locally via a USB connection or remotely via the FSK Gateway

The Rhino 232 alarm panel can be programmed via the following means:

4 Rhino 232 Installation Manual |

P O W E R STAT US TROUBLE

4 5 6

7 8 9

CLEAR 0ENTER CHIME

BYPASS

STAY

ARM

The Rhino 232 panel Wireless Devices

Bi-Directional

Raptor Remote Gate Module

Indoor PIR Door Contact Third Party

PIR Interface

Optional

Power Supply

USB Port for

Programming

PC for Local

Upload/Download

Remote Upload/Download

via the internet

Smart Phone Apps

RHINO 232 PANEL OVERVIEW

12V Strobe

(< 50mA)

12V Sound

Bomb

(< 200mA)

Piezo buzzers

Back view of panel

Rhino 232 Installation Manual 5 |

Power Supply

Optional

12V Sound

Bomb

Optional

12V Strobe

5V FROM

POWER

SUPPLY

ZONE 2

ZONE 1

AUX

12V

GND

SRN -+

STRB

COM

(≤ 200mA)

(≤ 50mA)

INSTALLATION

The alarm panel should be mounted in a location that has good GSM signal strength and that

is convenient for the user such as the living room or bedroom.

The alarm panel should be mounted away from metal objects as this will negatively affect the

performance of the wireless transceiver and GSM module.

Make sure the internal battery is plugged in as leaving it unplugged will negatively affect the

performance of the wireless transceiver and GSM module.

Mounting the alarm panel

Once the location has been chosen, remove the panel from the its bracket and mount the bracket

to the wall.

Use four 5mm screws and wall plugs to mount the bracket.

Tighten the screws until the bracket is ﬁrmly in place, but do

not over-tighten them.

Wiring the alarm panel

6 Rhino 232 Installation Manual |

Power Supply

Use only the 5V power supply with the alarm panel. A higher voltage supply or AC supply will

damage the alarm panel.

Connect the positive lead of the power supply to the positive terminal (5V) of the wall bracket

and the negative lead of the power supply to the negative terminal (GND) of the wall bracket.

Use a good quality security cable to do the connection like a ripcord cable.

NB. Please make sure to plug in the battery that is inside of the alarm panel.

Sound Bomb

The sound bomb may not draw more than 200mA.

Do not connect a conventional siren.

The alarm panel can drive an optional 12V sound bomb which can be used as an internal or

external siren.

NB:

Strobe Lamp

The alarm panel can drive an optional 12V strobe lamp.

Note: The strobe lamp must be a low current variet as it will shorten the y (not more than 50mA)

internal battery standby time.

Wired Zones

Up to two wired zones can be connected to the alarm panel (in addition to the wireless zones). The

wiring options for the zones are shown are in the next section. The auxillary 12V power supply can

be used to power up to two wired PIRs.

Note: Power supplied to the PIRs will shorten the internal battery stand-by time.

Wiring

Alarm Alarm

Normally Closed

Detector

Alarm

Normally Open

Detector

Normally Closed

Detector

with EOL

3K3

Piezo Buzzers

The alarm panel has two built-in piezo electric buzzers which sound whenever there is an alarm.

NB: These buzzers will only sound if one of the wired outputs is programmed as a siren/bell.

Rhino 232 Installation Manual 7 |

The detector contact is normally closed and opens when there is an alarm.

Program the zone wiring property to normally closed

NORMALLY CLOSED DETECTOR

The detector contact is normally open and closes when there is an alarm.

Program the zone wiring property to normally open

NORMALLY OPEN DETECTOR

The detector has a normally closed contact. The EOL resistor is used to detect that there is a

fault condition on the wire to the sensor.

Program the zone wiring property to single EOL-N/C

SINGLE END-OF-LINE (EOL) NORMALLY CLOSED

Wireless Zones

The wireless door contact has a reed switch which is used in conjunction with a magnet to sense if

a door is opened. In addition, there is an alternative of a zone input terminal.

Refer to the door contact leaﬂet.

RH-100 Wireless Door Contact

Use a CR2 3V Li-ion battery. Observe the polarity.

1. BATTERY

The tamper switch is used to detect the removal of the lid. It is also used for programming the

device into the panel.

2. TAMPER SWITCH

The LED lights when the device is sending a signal to the alarm panel.

3. ACTIVITY LED

8 Rhino 232 Installation Manual |

#I SecureGuard Installaon Manual

The wireless door contact has two detector inputs. The ﬁrst is the reed switch which is activated

by the magnet. The second requires a voltage-free normally closed contact to be wired into the

terminals. Both inputs report back to the same zone on the control panel. If the zone is not used,

it should be shorted out with a link.

4. ZONE INPUT TERMINALS

The magnetic reed switch detects the presence of the magnet ﬁtted to the door. There is a

marking on the door contact which indicates where the magnet should be centred. The magnet

should be mounted within 15mm of the door contact (when the door is closed).

5. MAGNETIC REED SWITCH

The antenna is used for transmitting the wireless signal.

NB. Avoid mounting the door contact on or near a metal frame as this will negatively affect

communications with the alarm panel.

6. ANTENNA

The RH-101 is engineered to be ﬁtted to third party PIR wireless-ready detectors. It has a normally

closed alarm input as well as a normally closed tamper input.

Refer to the in-box leaﬂet.

RH-101 Wireless 3rd Party Interface

Use a CR123A 3V Li-ion battery. Observe the polarity.

1. BATTERY

The tamper switch is used to detect the removal of the lid. It is also used for programming the

device into the panel. The tamper switch of a third-party PIR wireless-ready detector is used in

conjunction with the tamper terminal (5).

2. TAMPER SWITCH

The LED lights when the device is sending a signal to the alarm panel.

3. ACTIVITY LED

Rhino 232 Installation Manual 9 |

The normally closed contacts from the PIR are connected to these terminals. An alarm will be

sent when the PIR opens its contact.

4. ALARM INPUT TERMINAL

The normally closed tamper output from the PIR is connected to these terminals.

5. TAMPER INPUT TERMINAL

The antenna is used for transmitting the wireless signal.

NB. Avoid mounting the unit on or near a metal frame as this will negatively affect

communications with the alarm panel.

6. ANTENNA

The RH-200 indoor PIR has built-in wireless for direct communication to the Rhino 232 panel. The

PIR is allocated to one of the available wireless zones.

Refer to the in-box leaﬂet.

RH-200 Wireless Indoor Passive

Use a CR123A 3V Li-ion battery. Observe polarity (the

positive terminal is marked).

1. BATTERY

The tamper switch detects that the lid has been opened. It

is also used for learning the device into the panel.

2. TAMPER SWITCH

The LED illuminates when movement is detected.

3. ACTIVITY LED

The Raptor gate module has been speciﬁcally designed for controlling gate motors, garage doors,

etc. It has an output that can open and close a gate (control). Its input cannot be assigned to a

zone on the Rhino 232 panel.

Refer to the in-box leaﬂet.

Raptor Bidirectional Gate Module

If this jumper is on, the sensitivity is normal. If it is off, the

sensitivity is high.

4. SENSITIVITY JUMPER

If this jumper is on, the LED is enabled. If it is off, the LED is

disabled.

5. LED JUMPER

10 Rhino 232 Installation Manual |

Table des matières

Autres manuels FSK Panneau de contrôle

FSK

FSK RHINO 816 Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques