FS RS7250 Manuel utilisateur
DUAL INTEL® XEON® SCALABLE
PROCESSORS 2URACKMOUNT SERVER
ZWEI INTEL® XEON® SKALIERBARE PROZESSOREN 2HE RACK SERVER
SERVEUR À DEUX PROCESSEURS INTEL® XEON® SCALABLE 2U À
MONTAGE EN RACK
Quick Start Guide V3.0
Quick Start Anleitung
Guide de Démarrage Rapide
RS7250
1
2
BMC
Introduction
Accessories
Thank you for choosing RS7250 Rack-mount Server. This guide is designed to familiarize you with the
layout of the server and describes how to deploy the server in your network.
A pair of Gloves Power Cord x2
1
RS7250
Sliding Rail x2
EN
1
2
BMC
Hardware Overview
Front Panel
Buttons/Ports
LEDs
HDD8
HDD4
HDD0
HDD9
HDD5
HDD1
HDD10
HDD6
HDD2
HDD11
HDD7
HDD3
The Diagram of Hard Disk Sequence
2
4
3
5/6
11
Power
BMC
ID
USB 3.0
VGA
Power button. Press the button to boot the server when it’s
powered on. Press the button for 5 seconds to power off after
the server booted.
Button for rebooting BMC.
Server identification indicator button. Press the button to turn
on the ID indicator, then press the button to turn off.
USB 3.0 ports.
Front VGA port.
Number Button/ Port Description
2
8
Power
System
Status
Solid Blue
Blinking Red
Solid Red
The server started.
9Network 1 Solid Green On-board network 1 is connected normally and in
active state.
10 Network 2 Solid Green On-board network 2 is connected normally and in
active state.
4Hz: The power module is abnormal.
2Hz: The fan or the voltage sensor is abnormal.
The temperature sensor is abnormal.
3ID Blue The ID indicator is on.
7Hard Disk Red On-board PCH hard disk read/write.
Number LED State Description
2
EN
Information Label
2
3
4
11
6
1
8
7
9
10
5
BMC
1
2
Back Panel
1-2
3-4
5-10
11-12
13
14
15-17
Install 2.5-inch modules(optional). Support SAS/SATA//NVME hard disks.
Only support one PCI-E 3.0 X8 by default. Optional two-slot kit(one X8 and one X16).
3 PCI-E 3.0X8 adapter cards. Pci-e3.0x16 and PCI-E3.0X8 are optional.
Two LAN1 interfaces which are connectable to category 6 Gigabit cables (100MB
or less is not supported).
ID indicator.
VGA port which is connectable to VGA port display or other display devices.
USB 3.0 ports which are connectable to keyboards/mouses/3.0 USB flash drive or
other devices.
Number Description
NOTE: Hz indicates the number of times a flashing light blinks per second.
19-20
21
22
OCP network interface 1/2. Different types of OCP cards are available.
18 IPMI/IPMI2.0 port which is connectable to category 6 Gigabit cables. The server can be
monitored and managed via this port.
Serial port.
Power supply.
123465 7 98 10
11
22
12 13 14 18 21 19 20
17
16
15
3
EN
LAN1 LAN2 ID VGA IPMI
USB3.0
Motherboard
The layout of the motherboard with jumper, connector and LED locations is shown as below. See the
table on the following page for description.
4
EN
CPU0 CPU1
OCP1
OCP2
JTPM1
M21
PCIESLOT1
COM1
LCM1
JUSB2
BMCLAN1
J4
J5
JBAT8
VGA
UID LED
LAN2
LAN1
BAT1
PCIESLOT3
U37HS1
J11
J2
PCHHS1
PCIESLOT2
JSDO8 JPWR2
JPWR11 JPWR1
JPWR9
JPWR8
JPWR7
JPWR5
JPWR10
JPWR1
CPU1DIMM2
CPU1DIMM1
CPU1DIMM4
CPU1DIMM3
CPU1DIMM6
CPU1DIMM5
CPU0DIMM1
CPU0DIMM2
JFAN1 JFAN7 JFAN2 JFAN8
JFAN9
JFAN3 JFAN4
JFAN10 JFAN12 JFAN6
CPUVRHS1
JFAN11
JFAN5
CPU-VR-HS2
CPU0DIMM4
CPU0DIMM3
CPU0DIMM6
CPU0DIMM5
CPU0DIMM11
CPU0DIMM12
CPU1DIMM9
CPU1DIMM10
CPU1DIMM7
CPU1DIMM8
JAVGA1
OCULNK3
OCULNK4
OCULINK2
OCULINK1
JUSB5
J1
JPWR12
JCHASSIS1
JUSB4
CPUODIMM8
CPUODIMM7
CPUODIMM10
CPUODIMM9
CPUODIMM12
CPUODIMM11
MINISASHD3
MINISASHD1
MINISASHD2
SSATA5
SSATA4
JBAT8
JSDO8
Names
OCP1
OCP2
MINISAS HD1
MINISAS HD2
MINISAS HD3
Buzzer
Battery
JTPM1
Jchassis1
JUSB4
J1
JFP1
CPU0_DIMM1-12
CPU1_DIMM1-12
JFAN1-JFAN6
JVGA1
JPW10
J4
J5
Oculink1
Oculink2
Clear CMOS
Flash Memory Security Override
Pins 1-2(Restore jumper)
Pin 1-2(Normal)
OCP Type A Slot
OCP Type C Slot
Intel PCH SATA 0-3
Intel PCH SATA 4-7
Intel PCH SASTA 0-3
Motherboard buzzer
Motherboard battery
TPM port
Intrusion alarm port
USB 3.0 connector
Front I²C port
Front control panel connector
Memory slot 1-12 of CPU0
Memory slot 1-12 of CPU1
Connector 1-6 of 2U fan
Front VGA connector
Rear 2*2.5 inch HDD module power-supply connector
Rear 2*2.5 inch HDD SGPIO connector (SSATA4-5)
Rear I²C port
Oculink1 port
Oculink2 port
Oculink3
Oculink4
JPWR5
JPWR7~9
JPWR1
JPWR2
U57
U34
PCI-E_SLOT1
PCI-E_SLOT2
Oculink3 port
Oculink4 port
GPU power-supply port
Front HDD hard disk rear panel power-supply ports
Power module 1 port
Power module 2 port
BIOS ROM port
BMC ROM port
PCI-E3.0×24(CPU0) of adapter card
PCI-E3.0×24(CPU1) of adapter card
Jumpers Description
Description
Default Setting
5
EN
PCI-E_SLOT3 PCI-E3.0×8(CPU1)
SSATA4-5 Intel PCH SSATA 4-5
LAN1-2
UID LED
VGA1
BMC_LAN1
JBUS2
Motherboard integrated network port 1-2
Node Recognition LED
Motherboard integrated VGA
BCM Dedicated network port
Motherboard integrated USB3.0×3
Installation Requirements
Before installation, make sure the following conditions are met:
Server Mounting
Rack Mounting
Mount the server on the rack.
Make sure the rack is stable enough to mount the server.
The server should be mounted in a clean, dust-free and well-ventilated site.
There should be at least one three-prong power socket in the mounting site.
The server should be isolated from strong electromagnetic fields and electrical noise generating
equipment.
Reserve space for easy server maintenance.
CAUTION: To prevent bodily injury when mounting or maintaining the server in a rack, please
take special precautions to ensure that the rack remains stable. The following guidelines are
provided to ensure your safety:
1. If there’s no other equipment on the rack, the server should be mounted at the bottom of
the rack.
2. Equipment(including servers) mounted on the rack should be mounted from the bottom to
the top according to weight.
3. If the rack is provided with stabilizing devices, install the devices before mounting or
maintain the server.
4. Equipment mounted on the slide rails should not to be used as a shelf or a work platform.
6
EN
1. Mount the inner rail of the sliding rail on both sides of the chassis to fix the inner rail with screws.
2. Mount the outer rail of the sliding rail on the rack.
3. Lift the server up, then align it to the middle rail.
4. Push the server into the outer rail. When a“click” sound is heard, pull the blue block at point B in the
arrow direction to push the server into the rack.
5. Open the plastic cover at point C/D and tighten the screws.
NOTE: If you cannot not pull out the server when a“click” sound is heard, you can pull the
white block at point A or blue block at point B in the arrow direction to pull the server out.
7
EN
1
2
BMC
C
D
B
A
1
2
BMC
1. loosen the two screws on both sides of the top cover.
2. Pull the plastic buckle of the top cover upward to remove the top cover.
NOTE: When mounting the top cover, press the plastic buckle down and tighten the screws
on both sides of the top cover.
Removing the Top Cover
Hard Disk Mounting
1. For 2.5 inch hard disk, fix the M3 screws from the bottom of the hard disk tray upwards.
8
EN
M3 Screw
1
2
BMC
CPU Mounting
2. For 3.5 inch hard disk, fix the #6-32 screws from two sides of the hard disk tray inwards.
1. Align Point B and C of the processor with point B and C of the CPU mounting bracket.
2. Align Point A of the processor with PIN1 of the CPU mounting bracket.
3. Secure the processor on the CPU mounting bracket.
9
EN
A
A
B
B
C
C
pin1
#6-32
Screw
Table des matières
Langues :
Autres manuels FS Serveur
