Frontpoint ADC-V724 Manuel utilisateur
OUTDOOR CAMERA
3
OVERVIEW
The Outdoor Camera is a powerful tool for home security
and awareness, equipping you with world-class features:
• Two-Way Audio to talk with visitors outside
your home
• Smart notifications and clip recordings based on
Video Analytics
• Smart intruder-deterrence based on your
configuration of the new Video Analytics Rule,
“Perimeter Guard™”
In the following pages of this manual, we guide you
through the three-part setup process:
1. Wi-Fi setup to connect the Outdoor Camera to your
Frontpoint account
2. Installation to mount the camera in the desired outdoor
location
3. Video Analytics configuration, including Perimeter
Guard™
For reference on usage and the camera’s LED colors,
please refer to pages 8 and 9.
IN THE BOX
Outdoor Camera Wall anchors & screws (x3)AC power adapter
4 5
Wi-Fi SETUP CONT.
3. Open the menu ( ) in the Frontpoint mobile app.
• Select “Add Device”
• Select “Video Camera”
• Select “ADC-V724”
4. Follow the on-screen instructions until the installation
completes successfully.
During the setup, you will be asked to connect to a
temporary network that resembles ADC-V724
(XX:XX:XX).
The Xs are representative of the last six digits of the camera’s MAC
address, located on the bottom of the camera body. When firmware
updates are available, the installation can take up to 15 minutes.
When the Status LED turns solid green, the camera is successfully
connected to your Wi-Fi.
5. Tap “Next” to begin configuration for your camera’s
recording behavior.
6. When prompted to “place” your camera, follow the
mounting instructions on the next page before
completing the “Additional Set Up”.
Wi-Fi SETUP
To complete the setup, you will need a smartphone and a
2.4 GHz or 5 GHz Wi-Fi connection.
To add the Outdoor Camera to your Frontpoint account,
follow the steps below:
1. Connect your camera to the AC power adapter and
plug it into an indoor outlet near your router, if
possible.
You will move and mount the camera after Wi-Fi Setup is complete.
2. Log in to the Frontpoint mobile app on your
smartphone.
The camera boot-up takes about 25 seconds. When the Status LED is
blinking white, the camera is ready to continue.
If the Status LED is not blinking white after boot up, press and hold the
Reset button for about 6 seconds or until the Status LED begins to
blink white.
Status LED
Reset Button
6 7
MOUNTING
You will need a power drill, a drill bit (see anchor
installation options), the included mounting sticker, wall
anchors, and screws.
To mount the Outdoor Camera, follow the steps below:
1. Choose a mounting location.
It is best to use an indoor outlet or a locked waterproof outdoor outlet.
The outlet needs to be within 14 feet of your mounting location.
2. Peel off the backside of the included mounting sticker,
exposing the adhesive.
3. Apply the mounting sticker where you intend to mount
the camera. The sticker serves as a template to drill the
holes in the next step.
4. Prepare your power drill and drill into each of the three
targets ( ). See options Aand Bbelow:
Wall anchor installation is recommended when
installing screws into drywall or brick. Wall anchors
may not be necessary when installing screws into
wood.
A. Wall anchor installation
• Use a 1/4” drill bit to drill 1 1/2” deep holes at
each target ( ) from the mounting template.
• Insert a wall anchor into each hole
B. Non-wall anchor installation
• Use a 5/32” drill bit to drill 1” deep holes at
each target ( ) from the mounting template.
MOUNTING CONT.
5. Route the Outdoor Camera’s power cable using either
of the techniques below:
A. Through the wall
• Drill a hole through the center of the template
( )all the way until reaching the other side of
the wall.
• Gently remove the mounting sticker and
discard.
• Pull the power cable through the hole and
connect it to the AC power adapter cable.
B. On the wall
• Gently remove the mounting sticker and
discard.
• Align the rubber insert channel (pre-installed)
with the channel in the camera base and route
the cable through both.
6. Hold the Outdoor Camera so the base aligns with the
three drilled holes, and install a screw in each.
The camera body may need to be rotated or shifted to reach the screw
locations with a power drill.
7. When the camera is mounted and secure, proceed to
configure Video Analytics within the prompted
“Additional Set Up”.
Perimeter Guard™, a feature powered by Video
Analytics, enables functionality for smart intruder-
deterrence and can be configured within the setup for
Video Analytics.
USAGE GUIDE
After securely mounting and positioning your camera,
you’re ready to use your camera! Access live video and
saved clips, Two-Way Audio, and adjust the Video
Analytics configuration in the Frontpoint mobile app.
LIVE AND SAVED VIDEO
Tap “Video” in the left-hand menu.
• In the “Live” menu, tap the play button in the video
window to view live video.
• In the “Saved” menu, tap a video clip to review
your recording.
TWO-WAY AUDIO
Open your camera’s live video window in full screen.
• Tap the play button ( ).
• Select the full-screen icon ( ).
• To speak through the camera, press and hold the
microphone button. Release the button to listen.
• Mute or unmute incoming audio by toggling the
speaker button. OR
VIDEO ANALYTICS
While video analytics rules are encouraged to be created
during the initial setup, they can be set up or modified at
any time. To create video analytics rules, follow the steps
below:
1. Select “Video” in the left-hand menu.
2. Select the gear in the upper right corner ( ).
3. Select “Recording Rules”.
4. Select “Add New Rule”.
5. Follow the on-screen instructions to continue.
98
LED REFERENCE GUIDE
Blinking red - Powered on and boot up is in progress.
Blinking white - Ready to connect to Wi-Fi.
Solid green - Ready to use and working normally.
Solid red - Trouble connecting to Wi-Fi.
Blinking red & green - Factory reset in progress.
The camera should be factory reset if there are issues during set up or
anytime the camera is not operating as expected.
To factory reset the Outdoor Camera:
• Press and hold the Reset button for about 15 seconds or until the
LED blinks red and green
• Release the Reset button. The camera will reboot.
WARNING: A factory reset restores factory-default settings. The camera
may need to be removed from your Frontpoint system and re-added when
the reset is complete.
10 11
CUSTOMER SUPPORT
To get answers to FAQs, chat with a live agent, or
reference the user guide, tap Support in the left-hand
menu of the Frontpoint mobile app.
- OR -
Visit frontpoint.com/support
To speak to an agent, call 1-877-602-5276
Table des matières
Autres manuels Frontpoint Caméra extérieure
