Friedrich Vert-I-Pak A-Series Manuel utilisateur

Vert-I-Pak®

SinglePackageVerticalAirCenditieningSystem

A-Series

24,000 BTU/h

Installation& OperationManual

920-159-01 (10-03)

920-159-01(10-03)

TableofContents

InstallationRecommendations......................................................................................................................................................... 3

LGeneralSpecifications

ModelNumberIdentificationGuide................................................................................................................................... 4

VERT-I-PAKChassisSpecifications ................................................................................................................................... 4

II. Installation

1. UtilityClosetDimensions................................................................................................................................................... 5

2. WallPlenum & ArchitecturalLouverInstallation................................................................................................................ 6

3. ElectricalInformation..................................................................................................................................................... 7-9

4. Indoor ReturnAirGrilleInstallation .................................................................................................................................. 10

5. DuctworkPreparationandCFM ....................................................................................................................................... 11

6. ChassisInstallation.......................................................................................................................................................... 11

7. ChassisFinalConnections(Electrical,Duct, Drain& WallThermostat)............................................................................ 12

8. FinalInstallationChecklist............................................................................................................................................... 12

III. ChassisOperation

9. ThermostatControl.......................................................................................................................................................... 12

10. LowAmbientProtectionfor Compressor & Fan................................................................................................................ 12

11. HeatingDefrost(Heat PumpModelsonly)........................................................................................................................ 12

12. FreshAirDoor................................................................................................................................................................... 13

13. CondensateDisposalSystem .......................................................................................................................................... 13

IV. Service,Maintenance&Warranty

14. Servicing/Chassis QuickChangeouts............................................................................................................................. 13

15. RoutineMaintenance....................................................................................................................................................... 13

16. Warranty.......................................................................................................................................................................... 14

V. Vert-I-PakAccessories.................................................................................................................................................... 15

Please read this manual thoroughly prior to equipment installation or operation. It is the installer's

responsibility to properly apply and installthe equipment. Installation must be in conformance with

the NFPA 70-2002 National Electric Code or current edition and Universal Mechanical Code current

edition and applicable local or national codes.

Proper installation is not difficult but it is essential.

920-159-01 (10-03)

Vert-I-Pak Installation Recommendations

Forproperunitperformanceandmaximumoperatinglife pleaserefertotheminimuminstallationclearancesbelow.

FigureI

VERT-I-PAK ®units must be installed on an outside wall. Confined spaces and/or covered areas should be

avoided. Units should be installed no closer than 12" apart when two units are side by side. If three of more

units are to operate next to one another allow a minimum of 60" between units or pairs of units. Also, a vertical

clearance of 60" should be maintained between units. Units installed on the bottom floor should be mounted

at least 6" off of the ground.

SMALL RECESS OK

6_ _ h_

60"_

6" J

60" 60"

D D D

D D

D D D

_A_

LARGER RECESS OK iF A> 5xB

6o'_

60'_

12"

Figure2

Any time obstructions are present use

the following guidelines for proper

spacing from the VERT-I-PAK louver:

• For minor obstructions such as lamp

poles or small shrubbery a clearance

of 24" from the outdoor louver should

be maintained.

• For major obstructions such as a solid

fence, wall or other heat rejecting

device like a condensing unit, a mini-

mum distance of 72" should be kept.

BUILDING

OUTDOOR -72"

UNiT FENCE

MAJOR OBSTRUCTION

The above suggestions arefor reference only and do not represent all possible installations. Please contact the factory

for information regarding affects of other installation arrangements.

By following these simple recommendations you can be ®

confident that your Friedrich Vert-I-Pak will provide years

of worry-free operation.

920-159-01 (10-03)

Section I. GeneralSpecifications

MODEL NUMBER

SERIES

V=Vertical Series

E=Cooling with or without electric heat

H=Heat Pump

DESIGN SERIES

A = 32" and 47" Cabinet

NOMINAL CAPACITY

A-Series (Btu/h)

09 = 9,000

12 = 12,000

18 = 18,000

24 = 24,000

VOLTAGE

K=208/230V-1Ph-60Hz

LENGINEERING CODE

OPTIONS

RT = Standard Remote Operation

SP =Seacoast Protected

ELECTRIC HEATER SIZE

A-Series

00 = No electric heat

25 = 2.5 KW

34 = 3.4 KW

50 = 5.0 KW

75 = 7.5 KW

10= 10KW

Voltage (V)

Refrigerant

Chassis Width

Chassis Depth

Chassis Height **

Supply Duct Collar***

Drain Connection

Min. Circuit Amps

CFM Indoor

Max. Duct ESP

MODEL: V(E,H)A24

230/208

R-22

23.125

47.25

10"

3/4" FPT

See Nameplate

See chart, pg. 11

,4 in,water

NOTES:

** Height includes 2" duct collar & isolatorsunder unit.

*** Factory collar accepts 10" flex duct.

920-159-01 (10-03)

II. Installation

1) UtilityClosetDimensions

Recommended utility closet dimensions and a typical indoor installation are illustratedin Figure 1. Three inchesminimum clearance on

three sides of the unit must be allowedfor return airflow, installationaccess and service access. See Figures 1 & 2 for clearances and

reference dimensions.

Figure 3 TypicalUtility Closet

j.'J! Chassis Shown in Closet, on Optional Platform

Field-supplied

Filter (25" x 20")

Rigid Ductwork

POWE

Disconnect

t/1-14 Wall Plenum

VPRG4 Access Panel &

Return Air Filter Grille

3" Clearance on ell

three sides

minimum for drain pan

Chassis is beneath unit is

shipped with required on all

vibration VEA/VHA24 units.

isolators Drain pen must be

installed installed prior to

chassis installaiion

Figure4 TopView

22.3

8.4

-- electrical II -- I 6.2

entrance

4.2

•Vert-l-Pak Chassis 2-ton dimensions:

23" wide x 23" deep x 47 1/4" high.

• VPAWP1-8/1-14 Wall Plenumcut-out

dimensions 24 5/8" wide x 30 7/8" high.

• VPRG4 Access Panel cutout dimensions:

27" wide by 55 3/4" high.

• See Figure 8 (Page 10) for proper

chassis installation.

NOTE: Drain pan must be installed in closet prior to chassis

insertion intoplenum. See Figure7 (page 8) for drain pan

installationdetails.

920-159-01 (10-03)

2) WallPlenumandArchitecturalLouverInstallation

A, Install the wall plenum (VPAWPl-8/l-14) components in accordance with the installation instructions provided with each accessory,

OIMPORTANT REMINDER: FRIEDRICH WALL PLENUM IS NOT DESIGNED TO CARRY STRUCTURAL

LOADS. PROPER WALL HEADER CONSTRUCTION IS REQUIRED. THE PLENUM REQUIRES

PROPER FLASHING, SHIM AND CAULK FOR A WEATHER RESISTANT INSTALLATION.

B, Ensure that the divider is adjusted properly for the depth of the wail in accordance with the accessory installation manual

Figure5

WallPlenum& OutdoorLouverInstallation

ProperHeader 1_ Caulk all 8

flange corners

(

Proper Flashing

Proper Caulking Inside Wall Plenum

(Part B)

ProperCaulking

Architectural louver VPAL2 mounted

on the outside wall plenum (Part A) Proper Flashing

Rough opening dimension 24 5/8" wide x 30 7/8" high.

Ensure that the bottom of theplenum is1 1/2" from the floor of the closet. Note: 9,000 /12,000 /18,000 installation

height may be different. Referto specific installationmanual forclarification.

For proper airflow, maintain aminimum distance of 12" between Vert-I-Pak units. Consult the factory for any

installationor application questions.

920-159-01 (10-03)

3) ElectricalInformation

Electrical Data

Volta,qe(V) 230/208 230/208 230/208 230/208 230/208 230/208

LRA - Comp. (A) 68 68 68 68 68 68

Coeling Current (A) 13.7/12.4 13.7/12.4 13.7/12.4 13.7/12.4 13.7/12.4 13.7/12.4

MIN. Ckt. Amps(A) 17.2/15.9 22.1/20.3 30.7/28.1 44.3/40.3 57.9/52.7 15.6/15.6

vlax Branch Circuit Fust (Amps) 25/25 25/25 35/30 45/45 60/60 20/20

Power Connection HARD WIRED

Recommended Branch

Circuit Wire Sizes* 14/14 12/12 8/10 6/6 4/6 14/14

AWG -American Wire Gauge

* Single circuit from main box. Based on copper wire, single insulated conductor at 60°C.

NOTE: Use copper conductors ONLY. Wire sizes are per NEC. Check local codes for overseas applications.

Sample Nameplate (see your chassis nameplate)

SER+AL NO

FRIEDRICH AIR COND}llONING CO,

SAN ANTONIO, TEXAS

VOLT_24,33,34

VC_-TAG_ RANG£: 253=197

RFJ'RtGCHARGE:"70ZS. R22

DES_N pReSSURE:375 PSK; HS /150 pSIG LS

COOLING; BIU_'iR 8

_R: 10

TOTAL COOUNG AMPS: 9

TOTAL FJJEC.H£AT A_PS: 15

EL_C_C HEAT WATTS: _8

USE ON SINGLE OUTLET CIRCUIT ONLY

WARNING

ELECTRICAL SHOCK AND

MOVING PARTS

CAUSE

HEATING AND

OLING EQUIPMENT

E OF l}'IEFOLLO_NG

CATEGORY

TOCOMPETE THE ASSEMBLY

WALL PLENUM:

VPAWP1-8

VPAWP1-14

OUTDOORGRILLE

VPAL2

INDOOR GRILLE

VPRG2

VPRG4

920-159-01 (10-03)

IMPORTANT: ALL 208/230V CHASSIS MUST BE HARD WIRED WITH PROPERLY SIZED

BREAKER. SEE NAMEPLATE FOR SPECIFIC CHASSIS ELECTRICAL REQUIREMENTS.

SEE PAGE 9 - FIGURE 8 FOR UNIT WIRING AND WALL THERMOSTAT WIRING. SEE PAGE

7 FOR WIRE SIZE. USE HACR TYPE BREAKERS TO AVOID NUISANCE TRIPS. ALL FIELD

WIRING MUST BE DONE IN ACCORDANCE WITH NEC AND LOCAL CODES.

3) Electrical Information (continued)

Figure6

Electrical Requirements

Note:All field wiringmustcomply with NEC and localcodes. It

isthe responsibility of the installerto insurethat the electrical

codes are met. [ll:l IJill[till

Wire Size Use ONLY wiring size recommended for single

outlet branch circuit.

Use ONLY type and size fuse or HACR circuit

Fuse/Circuit breaker indicatedon unit's ratingplate (See sample

Breaker on page 6). Proper current protection to the unit is

the responsibility of the owner.

Unit MUST be grounded from branch circuit to

Grounding unit, or through separate ground wire provided on

permanently connected units. Be sure thatbranch

circuit or general purpose outlet isgrounded.

Use recommended wire size given in tables and

Wire Sizing install asinglebranch circuit. Allwidng mustcomply

with local and national codes. NOTE: Use copper

conductors only.

Electric shock hazard.

Turn OFF electric power before service

or installation.

All electricalconnectionsandwiringMUST

be installed by a qualified electrician and

conformtotheNationalElectricalCodeand

all local codes which havejurisdiction.

Failure to do so can result in property

damage, personal injuryand/or death.

Figure7

Drain Connection

and Location

CAUTION

THE ACCESSORY DRAIN PAN

(VPDP1) MUST BE INSTALLED

BEFORE INSTALLING THE UNIT.

1. The accessory drain pan has two (2)

provisions (left & right) for connecting

an external condensate drain.

2. A field supplied condensate drain

system must be connected to one of

the two 3/4" FPT connections.

The remaining connection must be

plugged using the 3/4" pipe plug

(provided) and field suppled teflon

tape or pipe joint compound.

Failure to follow these procedures

may result in serious property

damage.

920-159-01 (10-03)

3) ElectricalData (continued)

Figure8

Electrical&ThermostatWiringDiagrams

RT2

THERMOSTAT

(FRONT)

FOR 208 VOLT MODELS ONLY

MOVE THE WHITE WIRE AS

SHOWN BELOW

COM. 208V 240V

TRANSFORMER

24V

T "IT BLACK

_IN_IL_TO_

_EL_V

NOTE: THE DIAGRAM ABOVE ILLUSTRATES THE TYPICAL THERMOSTAT WIRING AND 208

VOLT TRANSFORMER WIRING. SEE THE UNIT CONTROL PANEL FOR THE ACTUAL

UNIT WIRING DIAGRAM AND SCHEMATIC.

920-159-01(10-03)

4) IndoorReturnAirGrilleInstallation

There are three Indoor Return Air Grille options as shown in Figure 9, Choose the optionthat best suits your needs. Use the installation

instructions providedwith accessories for installation details,

Figure9

Retum Air Grille Options

Option I

VPRG4

Return Air Grille with AccessPanel

A field-supplied(25"x20") filteris

mountedinsidethehingedaccessdoor.

IOPlion 2

VPRG2

ReturnAir Grille

Unit requires a field-supplied

accessdoororpanelanda

16"x20"filter.

All Vert-I-Pak chassis are shipped with a20" x 14"

filter installed, Ifan accessory filter holder isto be

used,you MUST remove the factory shipped filter

from the chassis, Do NOT use two filters

Notes:

A. These are the Friedrich recommended return air grille /filter /access panel arrangements. Consult the factory on other

arrangements. Improper returnair arrangements will cause performance problems.

B. Return air arrangements are shown from the front, but can also be installed from the right or left side ofthe unit.

Autres manuels pour Vert-I-Pak A-Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Friedrich Climatiseur

Friedrich

Friedrich M09YJ Manuel utilisateur

Friedrich

Friedrich CP10 Manuel utilisateur

Friedrich

Friedrich M18YJ Manuel utilisateur

Friedrich

Friedrich Chill CP06 Manuel utilisateur

Friedrich

Friedrich Kuhl SS08 Manuel utilisateur

Friedrich

Friedrich CP10 Manuel utilisateur

Friedrich

Friedrich QuietMaster KM18 Manuel utilisateur

Friedrich

Friedrich WallMaster WCT08 Manuel utilisateur

Friedrich

Friedrich Kuhl + XStar Manuel utilisateur

Friedrich

Friedrich QuietMaster SL25 Manuel utilisateur

Friedrich

Friedrich Chill Premier Series Mode d’emploi

Friedrich

Friedrich M12YG Manuel utilisateur

Friedrich

Friedrich MR09Y1F Manuel utilisateur

Friedrich

Friedrich ZoneAir P09A Manuel utilisateur

Friedrich

Friedrich MRM36Y3J Manuel utilisateur

Friedrich

Friedrich ZoneAire PZH07K Manuel utilisateur

Friedrich

Friedrich The Insider Manuel utilisateur

Friedrich

Friedrich QStar SQ06 Manuel utilisateur

Friedrich

Friedrich Z-Star ZQ05C10 Manuel utilisateur

Friedrich

Friedrich Chill Premier Series Manuel utilisateur

Friedrich

Friedrich X-Star XQ05L10A Manuel utilisateur

Friedrich

Friedrich Uni-Fit Thru-the-Wall Series Manuel utilisateur

Friedrich

Friedrich ZStar ZQ05A10B Instructions de construction

Friedrich

Friedrich VERT-I-PAK VEA09 Instructions d'utilisation d'origine

Manuels Climatiseur populaires d'autres marques

Spheros

Spheros CC 355 Manuel utilisateur

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuel utilisateur

Panasonic

Panasonic CS-E12HKEW Manuel utilisateur

nedis

nedis ACMB1WT7 Manuel utilisateur

Samsung

Samsung AR KV Series Mode d’emploi

Daikin

Daikin FCFV50A Manuel utilisateur

Fujitsu

Fujitsu Inverter ASBA30JFC Manuel utilisateur

Toshiba

Toshiba RAS-M10SMUV-E Manuel utilisateur

Daikin

Daikin FXLQ20MAVE Manuel utilisateur

Hitachi

Hitachi RAS-E24CAK Manuel utilisateur

CIAT

CIAT Magister 2 Series Mode d’emploi

Bestron

Bestron AAC6000 Manuel utilisateur

Hisense

Hisense 7K Manuel technique

Frigidaire

Frigidaire FFRE0533S1E0 Manuel utilisateur

Samsung

Samsung AS09HM3N Manuel utilisateur

Frigidaire

Frigidaire CRA073PU11 Manuel du propriétaire

Soleus Air

Soleus Air GB-PAC-08E4 Manuel utilisateur

McQuay

McQuay MCK020A Manuel utilisateur