FRC TH4 Manuel utilisateur

Installation Guide

TH4

4-Channel Hybrid DVR

Document Number:

XE-SNB2-TH4PM-R0A

TH4 Installation Guide

Table of Contents

System Components. . . . . . . . . . . . . . . . . . . . . . . . . .4

Required Tools & Equipment. . . . . . . . . . . . . . . . . . .4

System Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

TH4 Series Installation.. . . . . . . . . . . . . . . . . . . . . . . .6

Installation Best Practices. . . . . . . . . . . . . . . . . . . .6

Installing the DVR.. . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing the Adaptor Harness (Optional). . . . . . . .8

Installing the Expansion Harness (Optional).. . . . .8

Firmware Updates. . . . . . . . . . . . . . . . . . . . . . . . . .9

Hardware Installation Checklist. . . . . . . . . . . . . . .10

TH4 Operation.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

DVR Front Panel Features. . . . . . . . . . . . . . . . . . 11

DVR Back Panel Features.. . . . . . . . . . . . . . . . . .12

Video System Status. . . . . . . . . . . . . . . . . . . . . . .13

Video Flagging. . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Using On-screen Keyboards. . . . . . . . . . . . . . . . .14

Health Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

TH4 Administration . . . . . . . . . . . . . . . . . . . . . . . . . .16

Accessing the On-screen Display. . . . . . . . . . . . .16

Working with Video.. . . . . . . . . . . . . . . . . . . . . . . .19

TH4 Basic Conguration.. . . . . . . . . . . . . . . . . . . . .22

Setting up the DVR. . . . . . . . . . . . . . . . . . . . . . . .22

Time/Date Menu.. . . . . . . . . . . . . . . . . . . . . . . . . .24

Title/Display Menu. . . . . . . . . . . . . . . . . . . . . . . . .25

Camera Settings. . . . . . . . . . . . . . . . . . . . . . . . . .28

Signals Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Alarm Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Copying DVR Conguration. . . . . . . . . . . . . . . . .33

TH4 Advanced Conguration. . . . . . . . . . . . . . . . . .35

Conguring Recording Settings.. . . . . . . . . . . . . .35

Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . .36

Advanced Network Settings. . . . . . . . . . . . . . . . .38

VMS Servers. . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

G Sensor Options.. . . . . . . . . . . . . . . . . . . . . . . . .40

Speed Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . .42

GPS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

User Levels.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

System Settings. . . . . . . . . . . . . . . . . . . . . . . . . . .45

Monitor Settings. . . . . . . . . . . . . . . . . . . . . . . . . . .46

Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Customer Service.. . . . . . . . . . . . . . . . . . . . . . . . .48

Product Information. . . . . . . . . . . . . . . . . . . . . . . .48

Warranty And End-User License Agreement. . . .48

p. 4

System Components

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

System Components

The typical installation components are listed below. The actual contents of your installation package may vary,

depending on the options selected.

• TH4 video recorder with hard drive, locking front cover, cable cover, fasteners, and mounting plate.

• Analog High Denition cameras (HD1W or HD1Q) and Analog Standard Denition cameras (CA10, CJ, CQ or RVC)

• Camera harness (HExHD for AHD and HE or HExHD for SD)

• Power harness (PH2X2MFJR)

• Adaptor harness (WT1)

• Expansion harness (optional)

• G-Sensor (G-SENSOR-EXT)

• Diagnostic button (optional) and extension cable

• Smart-Reach cellular router and Smart-Reach WiFi bridge

• Smart-Reach GPS receiver

• Portable video monitor (optional)

• SD card (optional)

Required Tools & Equipment

The DVR system must be installed by a professional installer. A professional installer has the experience and equipment

to install and congure this DVR system to run properly.

Check that you have all the system components and inspect the units for any scratches or damage before installing.

Keys included in package contents:

• DVR keys for securing the removable hard drive.

• Front cover keys for securing the removable front cover.

Conguration equipment:

• For on-screen conguration: portable video monitor and mouse.

• For vMax Web conguration: laptop and an Ethernet cable.

p. 5

System Diagram

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

System Diagram

Click here to see an Interactive System

Diagram with more information.

p. 6

TH4 Series Installation

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

TH4 Series Installation

Installation Best Practices

This section provides best practices for installing Seon TH4 DVRs. Before you begin, keep in mind that it is your

responsibility to avoid damaging safety or electrical systems. If you are not condent in your ability to perform the

procedures in this guide, please contact FRC Technical Service at 1.800.645.0074 or visit the FRC website Contact

page for assistance.

The following table outlines the physical and environmental requirements for installing a TH4 DVR:

VENTILATION Install the DVR away from any sort of heat outlet, heater, or AC blower. Do not operate

the DVR in a closed-in area, or restrict ventilation in any way. The DVR requires air

circulation to maintain optimum operation temperature and provide best performance.

Do not expose the DVR to moisture!

SURFACE Do not mount the DVR to a plastic panel or other surface that is subject to constant

vibration.

ORIENTATION Mount the DVR in either a horizontal or vertical orientation, or hung right side up, but

NOT upside down.

CLEARANCE Allow sufcient clearance of at least 6 inches in front of the DVR and 2 inches to each

side for removal of the security front cover and easy access to the hard drive and USB

ports. Allow sufcient clearance behind the DVR for camera cables, mounting cables,

Ethernet cables, and power cables.

MOUNTING

CABLES

The radius for the mounting cables will be dictated by the cable cover. The rear-most

surface of the cable cover will be about 3 inches from the back of the DVR to allow

camera cables to bend over each other.

ETHERNET

CABLES

Avoid right angle bends in the Ethernet cables.

POWER CABLES Provide enough slack on the power cable to prevent any force from being exerted on the

connectors. A single 4-inch diameter loop is sufcient.

WARNING:

It is your responsibility to avoid damaging safety or electrical systems. Ensure you read and understand the TH Series DVR

Installation Requirements.

If you are not condent in your ability to perform the procedures in this manual, please contact FRC Support at 1.800.645.0074

or service@reresearch.com.

p. 7

TH4 Series Installation

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

Installing the DVR

The DVR typically ships with the locking front cover, mounting plate, and cable cover off, but in the shipping box.

The hard disk drive is in a separate box in the system shipping kit.

To install the DVR:

1. Select an appropriate mounting location and

orientation: horizontal or vertical.

2. Insert a hard drive in the DVR.

3. Insert the key into the hard drive lock and rotate a

quarter turn to lock the drive.

4. Use the mounting plate to mark the desired position

of the DVR and drill the four mounting holes.

5. Fasten the mounting plate to the mounting surface

with the four self-drilling screws.

6. Slide the rear bottom edge of the DVR into the spring

tab on the back edge of the mounting tray.

7. Attach the front bottom edge to the front of the DVR

using the two pan-head Phillips screws.

8. Connect the necessary cables and components.

9. Attach the cable cover to the DVR using the thumb

screws provided.

10. When DVR installation is complete, attach the front

door by hooking the door along the top edge and

turning the key to the locked position.

p. 8

TH4 Series Installation

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

Installing the Adaptor Harness (Optional)

The Adaptor Harness (Part # WT1) connects the DVR to Signal inputs, and to the optional Event/Diagnostic button

and Wake on Input trigger.

Installing the Expansion Harness (Optional)

The Expansion Harness (Part # 060-1059) can connect the TH4 DVR to Student Tracking and Rear Vision systems,

and provide a digital output to trigger other devices when an Alarm is detected.

To install the Adaptor Harness, connect the 2x6

Microt to the SIGNALS socket on the DVR.

Then:

1. Connect the 5 signal input wires.

2. Connect the 1x5 Microt to the Adapter

harness for the Event/Diagnostic button

(optional).

3. Remove the 1x3 Microt and connect the

green and black wires to a Wake on Input

trigger (optional).

To install the Expansion Harness, connect

the 2x4 Microt connector to the EXPANSION

socket on the DVR. Then:

1. Connect the 4-pin to the Student Tracking

harness (optional).

2. Connect the 2-pin to the Rear Vision

System harness (optional).

3. Connect the Digital Out black and blue

wires (optional) as shown in the Installation

Diagram.

p. 9

TH4 Series Installation

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

To update the Firmware version:

1. Power up the DVR using the vehicle ignition.

2. Insert the USB memory device with the new rmware version into the USB port on the DVR.

3. After the DVR starts up, right-click in the On-screen

Display and select

Conguration -> System -> Program Update

4. In the Program Update tab, click Update. A conrmation

window appears.

5. Click Yes to proceed or No to cancel. Yes starts the

rmware update, and a progress bar displays the

percentage complete.

6. Once the update is nished, the DVR

automatically restarts.

7. Remove the USB memory device.

Firmware Updates

Firmware controls how DVR features operate, including the Playback and Conguration menu displays. Seon may

direct you to install a rmware update when new features are added or specic issues are addressed.

The current rmware version appears in the top-right corner

of every Conguration menu. For instructions on opening the

Conguration menus, see TH Administration: Accessing the

On-Screen Display.

Only install rmware updates as directed by FRC Service.

NOTE: Firmware Updates

After restarting, the DVR may take up to 3 minutes to load and complete the upgrade. Wait until the DVR nishes loading.

NOTE: Completing Upgrade

p. 10

TH4 Series Installation

TH4 Installation and Setup Guide

Document Number: XE-SNB2-TH4PM-R0A

HARNESSES (CAMERA, RECORDER, AND ACCESSORIES)

Ensure cables and harnesses are properly secured.

Check that sharp metal edges are not touching cables or harnesses.

Ensure connections are solid (no shorts).

CAMERAS

Ensure tight mounting.

Examine the internal harness connections and ensure they are solid.

Ensure the lid is properly seated on the gasket and secured tightly.

Check camera(s) eld of view.

DVR

Ensure tight mounting.

Check that all connections are tight.

SYSTEM

Install fuses.

Plug portable video monitor into DVR, and power up the DVR from the vehicle ignition.

Congure the DVR to required specications locally using the mouse and monitor, or remotely by accessing

vMax Web via WiFi or Ethernet using a PC. For more information, see "Basic Conguration" on page 21.

Conrm the LAN, HDD, and PWR status indicators on the DVR front panel work properly.

Conrm that all cameras and audio sources operate properly.

Test audio/video record and playback.

Reformat the hard drives by navigating to Main Menu Conguration System Program Update

Format. A warning message tells you all data will be erased. Click Yes. When the process completes and

a message appears, click OK. Exit the Conguration setting menu, and system setup is complete.

Fasten and lock the front cover. Secure the cable cover on the DVR using the screws provided.

Hardware Installation Checklist

Table des matières

Autres manuels FRC DVR

FRC

FRC TH4C Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur