Franklin Electric SSI Series Manuel utilisateur

SUBMERSIBLES

SSI SERIES

Assembly Manual

franklinwater.com

Table of Contents

MACHINERY AND TOOLS - - - - - - - - - - - - 2

Submersible Tools & Equipment - - - 2

Tool Kit 305472639 - - - - - - - 2

Recommended Equipment for

Assembly Center - - - - - - - - - - 2

Assembly Table Dimensions - - - 2

Final Adjustment Bench

Dimensions - - - - - - - - - - - 3

Assembly Components - - - - - - - 3

ASSEMBLY INSTRUCTIONS - - - - - - - - 4

Bracket and Shaft Installation - - - - 4

Impeller & Diffuser Installations - - - 5

Strap Installations - - - - - - - - - - 6

Cable Guard Assembly- - - - - - - - 8

Preparation and Inspections - - - 8

6” Pump Cable Guard - - - - - - 9

8” and 10” Pump Cable Guard - - 11

Nameplate Installation - - - - - - - 12

MACHINERY AND TOOLS

Submersible Tools & Equipment

MACHINERY AND TOOLS

Submersible Tools & Equipment

The minimum basic manual tools and the equipment needed to assemble submersible pumps are:

1. Vernier Caliper type Height Gage, 0-150 mm for verifying the height of the arrow

2. Ratchet for 11/16” fastening screws

3. Ratchet for 3/4” fastening tension screws

4. Allen wrench - 5 mm (for 6”, 8”, and 10” motor coupling), SAE or standard (T handle preferred)

5. Adhesive Loctite® 302-43

6. Rubber hammer

7. 19 mm and 24 mm sockets, 3/8 drive

Additional machinery and equipment would be required if the assembler wants to cut and remove the

rough edges of the motor and cable guards.

Tool Kit 305472639

• Ridged Assembly Fixture

• Assembly Fixture Bolts

• 6” and 8” Motor Shaft Tool

• Torque Wrenches (20-100 Nm, 40-200 Nm)

• Brace for Strap Assembly

• Collet Nut Sockets

Recommended Equipment for Assembly Center

It is recommended that furnishings be adapted similarly to those shown below to facilitate assembly.

Assembly Table Dimensions

A table or similar area with an opening for adjustment from below is recommended.

MACHINERY AND TOOLS

Assembly Components

Final Adjustment Bench Dimensions

Provides stability for elevated placement of the pump in horizontal position.

Assembly Components

Based on the pump model being assembled, a specific quantity of the following components is required:

A. Motor Bracket with First Stage

B. Discharge

C. Top Diffuser (no neoprene ring)

D. Intermediate Diffusers (with neoprene packing)

E. Standard Impellers

F. Motor Coupling and Key

G. Strap Nuts and Washers

H. Four (4) Straps

I. Shaft

J. Cable Guard

ASSEMBLY INSTRUCTIONS

Bracket and Shaft Installation

ASSEMBLY INSTRUCTIONS

Bracket and Shaft Installation

1. Insert shaft into the coupling with the key in the key-way.

2. Ensure shaft is seated completely into the coupling.

3. Install the motor bracket to the build fixture by aligning bracket

holes with four hubs on fixture.

4. Install the shaft onto the fixture, ensuring the coupling is com-

pletely seated on the shaft stub.

• Support table set up may vary, but access below the table

is recommended to secure shaft to build fixture.

5. Insert assembly fixture bolt from bottom of fixture. Screw into

coupling with Allen wrench until tight.

Pump Size Screw Description

6” M8 x 1.25 x 100 mm

M8 x 1.25 x 140 mm

8” & 10” M8 x 1.25 x 140 mm

ASSEMBLY INSTRUCTIONS

Impeller & Diffuser Installations

1. Insert the lower impeller (with large collet nut) onto the shaft.

• Use two flathead screwdrivers to pry the threaded collet

nut and screwdriver shaft over the impeller to force the

impeller lower into the pump shaft.

2. Tighten the nut to the correct torque.

3. Only on the first impeller, place the graphite disc on all models

with the exception of 360SSI in the SSI 6” Series and the 10” SSI

Series models.

4. Slide diffuser over the impeller and upthrust washer until it is

seated completely on the motor bracket.

Pump GPM Torque (Nm)

85 25

150

225

300

360

425 60

475

550

180625

826

1150 300

ASSEMBLY INSTRUCTIONS

Strap Installations

5. Repeat the steps to install next diffusers until you reach the dis-

charge assembly.

• Insert impellers (A).

• Adjust as indicated using a torque wrench and the torque

chart indicated for each pump (B).

• When sliding the different diffusers to cover the impeller

point in the diffusers for a better final appearance (D).

NOTE: On all subsequent impellers using upthrust collet nut,

use two flathead screwdrivers between the collet nut and

impeller to pry down on the impeller and force it lower into the

pump shaft for proper seating.

Strap Installations

1. Install the upper diffuser (does not contain wear ring) and the

discharge.

• Make sure to align the strap locations on the discharge

with the holes in the motor bracket.

• Depending on the size of pump, the slot may have a differ-

ent configuration and location on the discharge.

2. Apply anti-seize (White Knight) to the threaded studs on the

strap.

3. Insert strap into slot so it is completely seated.

4. Slide threaded stud into motor bracket mounting hole.

• Ensure the stud extends through the hole.

ASSEMBLY INSTRUCTIONS

Strap Installations

5. Use a rubber hammer to tap the strap down to ensure it is com-

pletely seated.

6. Repeat steps 1 - 5 for each strap.

7. Slide washer onto the stud and thread nut for each strap.

8. Tighten to the correct torque.

• Refer to table below.

• Tightening in a crisscross pattern is recommended to main-

tain even torque on all sides.

• For 10” models, place Strap Blocks on motor bracket to

prevent strap twisting during installation and tightening

process.

NOTE: The stainless steel strap nuts have been anodized to pre-

vent galling.

Pump GPM Torque (Nm)

150

225

300

360

425 80

475

550

120

625

825

1150

ASSEMBLY INSTRUCTIONS

Cable Guard Assembly

Preparation and Inspections

1. Remove the pump from the build fixture by removing the fix-

ture bolt from underneath the fixture and lifting off the shaft

stub.

2. Lay the pump horizontally on the workbench or horizontal sup-

port.

3. Check that the pump shaft spins freely by inserting the appro-

priate Motor Shaft tool into the coupling and rotating.

4. Check that the shaft height is within the defined range.

• See table for dimensions.

• Measure with a shaft height gauge.

Risk of damage to pump or other equipment.

• On pumps with higher stage counts, support the center of the pump when laying it horizontal to pre-

vent the pump from bowing.

NEMA Shaft Dimension Shaft Down

(mm) Shaft Up

(mm)

6” 71 76

8” & 10” 99 104

ASSEMBLY INSTRUCTIONS

Cable Guard Assembly

5. Apply Loctite® 302-43 to the set screw from the motor coupling

kit.

6. Reinstall the screw on the shaft coupling, using a 5 mm Allen

wrench to tighten.

NOTE: If coupling O-Ring is not installed, place the O-Ring into

the coupling O-Ring groove, making sure it is placed properly.

7. Once secured, identify the cable guard included with the corre-

sponding pump model.

6” Pump Cable Guard

1. Orient the cable guard so the angled tab is on the motor

bracket end and the top two tabs extend past the pump’s dis-

charge.

2. Install the cable guard tabs closest to the motor bracket.

3. Gently tap the side of the cable guard to drive one of the tabs

under the strap.

• Do not tap the tabs.

ASSEMBLY INSTRUCTIONS

Cable Guard Assembly

4. Use the small flat-head screwdriver to gently raise the strap on

the opposite side of the cable guard.

5. Gently tap the other tab under the strap.

• Remove the screwdriver after the cable guard tab has

started under the strap.

6. Make sure the cable guard is centered between the two straps.

7. Repeat steps 3-6 for all the tabs except the top two.

8. After all but the top two tabs have been installed, gently tap the

top end of the cable guard down toward the motor bracket.

• Be careful not to damage or bend the cable guard.

9. Apply pressure to the end of the cable guard while tapping on

the top side of the tabs close to the motor bracket. This will

allow for the end of the cable guard to slide under the motor

bracket ears.

10. Gently tap the cable guard to drive one of the top two cable

guard tabs under the strap.

Table des matières

Autres manuels Franklin Electric Pompe à eau

Franklin Electric

Franklin Electric I Series Manuel utilisateur

Franklin Electric

Franklin Electric LittleGIANT 1 Series Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant VCMA Series Manuel utilisateur

Franklin Electric

Franklin Electric FAOT Series Manuel utilisateur

Franklin Electric

Franklin Electric VR Series Manuel utilisateur

Franklin Electric

Franklin Electric TurfBOSS TB15CI Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant 1.5-MDQ-SC Manuel de l'opérateur

Franklin Electric

Franklin Electric VersaJet Series Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant P-AAA Manuel utilisateur

Franklin Electric

Franklin Electric VR Spec PAK Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant WRS-8E Manuel utilisateur

Franklin Electric

Franklin Electric Turf Boss FTB3CI Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant PES-70 Manuel utilisateur

Franklin Electric

Franklin Electric Little GIANT 9EC Series Manuel utilisateur

Franklin Electric

Franklin Electric Little GIANT VCMA-10 Manuel utilisateur

Franklin Electric

Franklin Electric Turf Boss Manuel utilisateur

Franklin Electric

Franklin Electric Inline 400 Manuel utilisateur

Franklin Electric

Franklin Electric LittleGIANT MGP-1C18-2 Manuel utilisateur

Franklin Electric

Franklin Electric NCX Series Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant PE-1 Manuel utilisateur

Franklin Electric

Franklin Electric FLS-400 Manuel utilisateur

Franklin Electric

Franklin Electric Little Giant TPS Manuel utilisateur

Franklin Electric

Franklin Electric FBSE Series Manuel utilisateur

Franklin Electric

Franklin Electric LittleGIANT HT-10EN-CIM Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur

STA-RITE

STA-RITE ST33APP Manuel utilisateur