FOVNO ES-2CS Manuel utilisateur
全 电 动 吸 盘 行 李 箱 架 说 明 书
FOVNO Electric Sucker Luggage Rack Instructions
Please read these instructions carefully before using this product. The instructions contain important information
which will help you get the best out of the product and ensure safe and proper installation, use and maintenance.
· Do not squeeze or impact the product forcibly.
· Do not disassemble or modify this product.
· Children should be supervised to ensure that they do not use this product as a toy to avoid unnecessary accidents.
· This product needs to be used with the attached alarm, which serves as a reminder during the use of the roof rack. If, when in use, the alarm continues to sound please stop your
vehicle and check our troubleshooting guide. If you are unable to solve the issue, please refrain from using the product until you have contacted customer service.
· In normal use of this product, the suction foot will slowly leak air. When the air pressure inside the leaking suction foot reaches the set minimum pressure value, the N-Power
control box will pump the air automatically, and the alarm will sound. The alarm will stop after a few seconds. The time it takes the N-Power control box to create a vacuum
depends on the hose length and other system settings. Normal operating time is between 2 - 15 minutes and during this time it is normal for the alarm to sound.
· It is normal for the suction foot to leak slowly during use. If the control box starts frequently within 2 minutes(while the alarm keeps buzzing), It is considered to be air leaking too
fast. Frequent start of the control box will cause the internal motor to overheat and not function properly. If similar situations occur, please check whether the suction foot is
damaged, whether the suction part is flat and smooth or whether the hose and quick connector are damaged immediately. If the above problems are removed, but the frequent
start-up phenomenon still occurs, it could mean something is a problem with the product. Please contact customer service immediately. Some products have a particularly
good sealing performance and when the adsorption surface is particularly smooth, it may cause the control box to work automatically at an interval of more than 20 minutes.
If the buzzing alarm doesn't go off for a long time, please open the suction foot, in which way, you will find out if the control box is working normally. If the control box is working
normally, there is no need to worry.
· Before use, please check the battery charge level in the N-Power control box and charge if needed. Do not use with a low battery.
· Before use, please check whether the roof rack control box is working normally with sufficient power. Press the control box sunction foot on a smooth surface, turn on the
power switch, and press the control box vertically with your hand. After all the suction foots seal to the surface, open any of the suction foots, the control box should start to
work and this suction foot should re-adsorb the surface immediately, this is what we consider normal operation (Meanwhile, connect to the power of the alarm. the alarm should
start to buzz with the control box starts to work, and stop when the suction foot adsorbed completely).
· Before use, make sure that the filter sponge at the suction port on the bottom of the suction foot is in good condition. The filter sponge has a great protective effect on the
adsorption of the suction foot. It prevents dust or other items from entering the suction pipe and guarantees the airtightness of the air valve in the suction foot.
Terms and Conditions
16
· Before use, please clean the roof area and the bottom surface of the suction foot to be installed with water and dry with a microfibre cloth. The suction foot can be installed after
ensuring that the area is free of dust and water.
· When using, please install the roof rack on a flat and smooth part on the roof. The surface where the suction foots are placed must not have cracks. Do not install the roof rack in
places where there vinyl stickers or where there are joins between panels, glass or plastic.
· While driving, check whether the control box is working normally every 4 hours using the method above, and check whether all the suction foots are functioning.
· When using this product, please pay attention to the following items: the highway speed should not exceed 120km/h, and the ordinary road should not exceed the speed limit
sign. Be aware of road conditions and drive slowly on uneven or bumpy conditions.
· There is a lithium battery in the control box of this product. The temperature will affect its efficiency. It is recommended to use in an environment at a temperature between
-20°C and +40°C.
· During use, if the control box cannot work normally due to force majeure, please do not panic. Each suction foot of this product is equipped with an air check valve. Even if the
control box is not working normally, the suction foot can still be firmly adsorbed for at least 1 hour. Please get off the car in a safe place to check and troubleshoot the problem.
If the control box still does not work normally, please stop using it immediately and contact our company's customer service for repair as soon as possible.
· When the roof rack is not in use, please dust seal plug the air pipe quick interface on the control box and the main suction foot with a rubber plug to prevent foreign objects from
entering and affecting the normal operation of the roof rack.
17
18
Learn about your new Electric Sucker Luggage Rack-Hatchback version
Introduction
Pneumatic hose
Front text
N-Power
Control box
Luggage mounting plate
Rear text
Left rear suction feet group
Front liftable suction foot
Front suction foot
Front suction foot
Protection cover
Right rear suction feet group
19
Pneumatic hose
Front text
Right triangle
N-Power
Control box
Luggage mounting plate
Rear text
Left rear suction feet group
Left triangle
Front liftable suction foot
Front suction foot
Front suction foot
Protection cover
Right rear suction
feet group
Learn about your new Electric Sucker Luggage Rack-Redan version
Introduction
20
(Dust seal: When the rack is not in use
please use the dust seal to protect the
pneumatic connections.)
Introduction
Alarm
Pairing
Alarm System Instructions
1. Your rack is fitted with a safety alarm which will alert you if the back loses its connection with the vehicle. The alarm
will sound if a suction foot leaks. In the even of this happening the N-Power system will automatically attempt to create a
vacuum seal using the built in pump.
2. The alarm module is fitted with a standard USB which can be connected to your vehicle either via the vehicles own USB, a
USB adaptor or USB port on a sound system. The alarm will connect to the N-Power box wirelessly and will alert you in the
even of a pressure error. Double sided toe on the underside of the alarm can be used to hold it in place.
3. PLEASE NOTE: If you are using more than one electric rack system on your vehicle the alarm system may not operate
correctly due to a shared signal. While the alarm may not operate the N-Power box will still function as normal.
N-Power control box functions
· Charging: Charging the N-Power box is easy and thanks to the USB-C connector you can charge from a phone charger power
band or a USB charger. Simply remove the waterproof / dust cover and charge with the included USB C wire.
· The N-Power control box features USB lights that tell you the level of charge in the battery. An orange light indicates the system
needs charging, blue means full and a red light indicate the system is being charged. To check the battery level press the button
on the N-Power control box.
N-Power Control Box
Dust seal plug
Quick release air hose connection
USB Type C connector Power button
Battery health check button
(Red light when charging
blue light when fully charged.）
（The blue light is normal, and the red
and orange are charged immediately）
red orange blue blue blue
The underside of the alarm
A button for the pairing switch
Pairing method of alarm and control box
1. Clear data: There is a small hole on the back of the
alarm that is a button for the pairing switch. After the
alarm is connected to the power supply, press the
switch button in the small hole for about 10 seconds
When the indicator light of the alarm is off, it meansthat
the original data is cleared.
2. Use the same method to press the switch button in
the small hole of the alarm for about 3-5 seconds. After
the alarm indicator lights up, start the control box, and
then stop pressing the pairing switch. At this time, the
alarm buzzes, the pairing is complete.
21
Suction filter
Base of foot Gasket
Warning: Ensure the suction foot filter is clean
and in good condition.
Introduction
Press in hose
Remove the dust seal plug
(please keep it in a safe place)
Hose Connection
Hose Disconnection
① ②
Replace the dust seal
plug when not in use
b.While pressing the lever
carefully pull the hose loose
a.Press the lever to release
the locking interface
① ②
Installation of your Electric Sucker Luggage Rack
Hatchback version and sedan have the same method
22
What's in the box
Introduction
Name Main Body Suction Foot Group
Right Rear Rack Suction Feet
Group×1
Electric Sucker
Luggage Rack
Hatchback
Version
Accessories Spares
Spare Board×4
Alarm×1
USB Type-C Cable×1
Pipe Fixing Buckle×6
5mm Allen Key×1Carriage Screw×8
Microfibre Cleaning Cloth×1
Square Gasket×8
Seals×4
Suction Foot Filters×4
CPC Dust Seal Plug×2
Hose Connector×4
4mm Allen Key×1
Specification
Model number ES-T02
Package size 850×180mm
System weight 7.5kg
Protection grade
Executive standard
Our products have acquired the UN38.3、EN62133
IP65
QC/T948-2013
Battery capacity 3400mAh
Input DC 5V
Power 13W
Maximum negative pressure -65KP
Wireless transmission frequency 433.92MHZ
Gaskets×4
Rear Frame×1
Front Frame×1
Left Rear Rack Suction Feet
Group×1
Lubricant ×1
Hand Nut×8
Model number
Package size
System weight
Protection grade
Executive standard
Our products have acquired the UN38.3、EN62133
Battery capacity
Input
Power
Maximum negative pressure
Wireless transmission frequency
Seals×4
Suction Foot Filters×4
CPC Dust Seal Plug×2
Hose Connector×4
Gaskets×4
23
Nylon Cable Tie
What's in the box
Introduction
Name Main Body Suction Foot Group
Right Rear Rack
Suction Feet Group×1
Left Rear Rack
Suction Feet Group×1
Right Triangle × 1
Electric Sucker
Luggage Rack
Redan version
Accessories Spares
Spare Board×4
Alarm×1
USB Type-C Cable×1Pipe Fixing Buckle×6 5mm Allen Key×1
Carriage Screw×8 Microfibre Cleaning Cloth×1
Square Gasket×8
4mm Allen Key×1
Specification
ES-T03
850×180mm
9.1kg
IP65
QC/T948-2013
3400mAh
DC 5V
13W
-65KP
433.92MHZ
Rear Frame×1
Front Frame×1 Left Triangle × 1
Lubricant ×1
Hand Nut×8
Figure Ⅰ
Figure Ⅱ
Figure Ⅲ Figure Ⅳ
This product is divided into hatchback version and sedan version, please install it according to the instruction manual of
the purchased product.
Hatchback rear frame installation
1. Install the suction feet group on the rear text, and tighten the screws as shown in Figure Ⅰ. Two spacers should be placed at the connection
to avoid shaking due to excessive clearance.
2. The
pneumatic hose
under the front frame and the rear frame text need to be fixed with pipe fixing buckles, as shown in Figure Ⅱ.
3. After the rear suction feet group is installed, connect the
pneumatic hose
on the rear frame to the joint of the rear suction feet group as shown
in Figure Ⅲ.
Note: During installation, the control box switch and the
pneumatic hose
on the suction feet group
face the rear of the vehicle, as shown in Figure Ⅳ.
The
pneumatic hose
towards the rear of the
vehicle
Fixed pneumatic hose
24
Instructions
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels FOVNO Accessoires pour vélos
