Fotopast BL480L-P Manuel utilisateur
4G/3G/2G GPS Cellular Trail Cameras
Supporting MMS/Email/FTP
User’s Manual
Contents
Introduction--------------------------------------------------1
Main Features------------------------------------------------1
Illustration-----------------------------------------------------2
Applications---------------------------------------------------3
Accessories----------------------------------------------------3
Peel Off---------------------------------------------------------3
Cleaning--------------------------------------------------------3
Power Supply-------------------------------------------------4
Inserting SD/Micro SIM cards-----------------------------5
Quick Start(NO sending pictures out)-------------------7
Screen display when in TEST mode----------------------8
Shoot Picture Information------------------------ ----------8
Specification----------------------------------------------------9
Connecting PC and Camera--------------------------------11
Checking Menu via Buttons--------------------------------12
MMS/Data(SMTP/FTP) Setup------------------------------28
How to config camera via PC-------------------------------30
How to send picture in TEST mode------------------------37
Changing setup after reading config file------------------37
FAQ List-----------------------------------------------------------38
After-sales Support--------------------------------------------40
1
Introduction
Congratulations on the purchase. Users have selected a
high-quality product. The operating instructions are a
constituent of this product. They contain important
information about safety, use and disposal.
Before using the product, familiarize all operating and safety
instructions. Use this product only as described and only for
the specified areas of application.
Main Features
♦ 112 degree wide angle lens
♦ 1080P Full HD video resolution
♦ 0.6 seconds trigger time
♦ IP66 waterproof, dustproof
♦ Supporting 4G/3G/2G network
♦ GPS location information
♦ Sending original pictures
♦ Sending 30S video
♦ Supporting FTP
♦ SMS remote control
♦ APP remote control
2
Illustration
Front & Bottom view:
1. Bottom 2. Microphone 3. PIR detection 4. Lens
5. 4G antenna 6. GPS antenna 7. logo space 8. light detection
9. Invisible IR 52pcs Leds 10. DC 12V Jack
11. Power switch( TEST/ON/OFF) 12. 7 Operation Buttons
13. color display 14. Built-in speaker
15. 12 AA battery depot
3
Applications
1. Trail camera for hunting
2. Animal or event observation,Fauna Surveys
3. Warehouse/Storage/Farm Area Surveillance
4. Home/Property Security
5. Farm Gates or Driveways
Accessories
1. Strap 2. USB cable 3. User manual
4. GPS antenna 5. 4G antenna 6.CD
Peel Off
There are transparent protective films on leds, lens, PIR and
screen. Please peel them off before camera usage.
Cleaning
Damage to the device!
■ To avoid irreparable damage, ensure that no moisture
penetrates the device during cleaning.
■ Clean the surfaces of the device with a soft, dry cloth. Use a
normal commercial detergent and water to remove stubborn
residue. Ensure that no water gets into the device.
4
■ Always keep the seal clean so that no moisture gets into the
device and damages it. Contamination of the seal can impair
the dust and water spray protection.
Power Supply
♦ To insert batteries in the device, first open camera and check
battery compartment on +-. When users replace the battery,
please replace all batteries. Do not max the old and new
batteries and do not mix alkaline, standard, and rechargeable
batteries.
♦ To increase the operating time, users can use 12 x 1.5 V
LR6/AA batteries in the battery compartment.
Please pay close attention to the polarity, which is marked on
the battery compartment. Otherwise the device will not work
and can be damaged.
♦ If users operate the device using a mains adapter (not
supplied), open the round rubber seal at button of camera
then connect the external mains adapter. The mains adapter
must supply a direct-current voltage of 12 V. Operation via a
mains adapter is possible with batteries inserted. If one power
source fails, operation will be maintained using the other.
5
Warning
1. Slide the power switch to OFF position to turn off the
camera, Please note that even in the OFF mode, the
camera still consumes a small amount of battery power.
Therefore, please remove the batteries if the camera is not
in use for a long time
2. Always have the camera in the OFF position when
installing or removing batteries and memory card.
Removing batteries or memory card while the camera is
ON may damage the camera.
Inserting SD/Micro SIM cards
► Since the camera has no built-in memory, it can only work
when an SD/SDHC memory card is inserted. After inserting,
6
please format the SD card via camera sub-menu ‘format’, so
that to improve the battery life and shutter speed.
► The device supports SD/SDHC memory cards with a
capacity of up to 32 GB.
►When the SD memory card is full, it will automatically stop
take picture and record video. And the light will be closed.
► To remove an SD/SDHC memory card, press the protruding
edge of the memory card in a little way until it pops out. Then
remove the card.
► To insert an SD/SDHC memory card into the memory card
slot of the device, push it into the slot until it clicks into place.
The contact surfaces of the memory card must be facing
towards the front of the camera.
► SD/SDHC memory cards have a locking system to prevent
accidental erasure. However, the camera can only save data
onto the card when SD card is not locked.
7
Quick Start(NO sending pictures out)
A. Switch camera to ON mode
Note: Camera comes default setting, so for testing purpose,
users only need to insert a SD card and batteries to let camera
work by turning camera to ON Mode. The red light will work
for 3 times and screen is off, then work on PIR and when
working during nighttime, there is no any visible light.
B. Switch camera from TEST to ON mode
When user need customized setting, please turn camera to
TEST mode, then the display will be on, please press
button ”MENU” to enter camera setting menu.
Using navigation buttons to obtain favored setting, press ’’OK’’
for confirmation and save the preferred change, press “MENU”
to exit current page.
Then turn camera from TEST to ON mode, The red light will
work for 3 times and display will be off, then work on PIR and
when working during nighttime, there is no any visible light.
8
Screen display when in TEST mode
Shoot Picture Information
Picture information strip: logo, serial number,
temperature, longitude and latitude, moon phrase and
date/time
Table des matières
