Fortress Technologies A Manuel utilisateur
Fortress Doorbell
Type A
www.FortressSecurityStore.com
Table of Contents
Pictures
Button Names
Features
First-Time Setup
Changing the Volume
Changing the Tone
Adding an Accessory
Factory Reset
Technical Specifications
Pictures
Doorbell Type A
DoorbellTypeADual
Doorbell Type A SOS
Button Names
LED Light
Volume Button
Music Note Button
Gear Button
Features
57 Available Tones
Adjustable Volume
Wireless Accessories (433 MHz)
Supports up to 10 Accessories
LED Status Light
FortressDoorbellTypeA
1 x DoorbellReceiver
1
x Wireless Doorbell PushButton
FortressDoorbellTypeA-Dual
1 x Doorbell Receiver
2
x Wireless Doorbell PushButtons
FortressDoorbellTypeA-SOS
1 x Doorbell Receiver
1 x Wireless Doorbell Push Button
1 x Wireless SOSNecklace
First-Time Setup
After taking the items out of the box,
follow these steps to begin using your
new Fortress Doorbell Type A.
1.
Remove Battery-Saver PullTab(s).
2.
PlugtheDoorbellReceiverintothe
wall outlet.
3.
Testthe Doorbell Push Button to make
sure the Doorbell Receiver plays a tone
successfully.
4.
Mount/InstalltheDoorbellPush
Button(s) in the desired location.
5.
Pairthe Doorbell Receiver with any oth-
er Fortress Accessories you may
have, as needed. (See ‘Adding
Accessories’).
Changing the Volume
1.
Press the VolumeButton to cycle
through the volumesettings.
2.
To select a volume level, press the Gear
Button,or just let the tone finish playing.
(4 volume levels available)
Changing the Tone
1.
Press the Music Note Button to cycle
through the availabletones.
2.
To select a tone, press the Gear Button,
or just let the tone finish playing (57
tones available).
To cycle through the zones in reverse
order, press and hold the Music Note
Button until the Doorbell Receiver beeps
once ( ~3 seconds).
This will not affect any accessories pro-
grammedwitha‘fixedtone.’(See‘Adding
an Accessory.’)
Adding an Accessory
The Doorbell Receiver can store up to 10
Accessories in its memory (including the
push button(s) and the SOS necklace).
1.
Change the current tone to the desired
tone for this accessory (See ‘Changing
the Tone.’)
2.
Press and holdthe Gear Button
( ~3 seconds).
The DoorbellReceiver willbeep once, and
the LED Light will be lit up.
3.
Trigger the Accessory to send a signal
to the Doorbell Receiver.
TheDoorbellReceiverwillbeeptwice.
4.
Press the GearButton to save.
The LED Light will go dark.
To add an accessory that will not change
tone (fixed tone), press and hold both the
GearbuttonandtheMusicNotebuttonat
the same time in Step 2 above.
Factory Reset
To remove all Accessories from memory,
follow these steps:
1.
Unplug the Doorbell Receiver.
2.
Press and hold the Gear Button.
3.
While holding the Gear Button, plug
the Doorbell Receiver into the wall outlet.
Continue holding the Gear Button ( ~10
seconds).
The Doorbell Receiver will beep several
times, then it will give a series of fast
beeps. It is now reset.
Technical Specifications
Power: 110-220V 50-60Hz AC
Working Draw: 0.5 Watts
Wireless Frequency: 433 MHz
Wireless Range: 150 feet w/ line of sight
Push Button Battery: 1 x 27A 12V
Ce manuel convient aux modèles suivants
2
Table des matières
