FOR-A FA-AUX30 Manuel utilisateur

FA-AUX30

Auxiliary Unit

1st Edition

(Version 1.00 or Higher)

OPERATION

MANUAL

Edition Revision History

Edit. Rev. Date Description Section/Page

1 - 2014/01/17 First edition

Precautions

Important Safety Warnings

[Power]

Operate unit only at the specified supply voltage.

Disconnect the power cord via the power plug only. Do not pull on the cable portion.

Do not place or drop heavy or sharp-edged objects on the power cord. A damaged

cord can cause fire or electrical shock hazards. Regularly check the power cord for

excessive wear or damage to avoid possible fire / electrical hazards.

[Grounding]

Ensure the unit is properly grounded at all times to prevent electrical shock.

Do not ground the unit to gas lines, units, or fixtures of an explosive or dangerous

nature.

Ensure the power cord is firmly plugged into the AC outlet.

[Operation]

Do not operate the unit under hazardous or potentially explosive atmospheric

conditions. Doing so could result in fire, explosion, or other hazardous results.

Do not allow liquids, metal pieces, or other foreign materials to enter the unit. Doing

so could result in fire, other hazards, or a unit malfunction.

If a foreign material does enter the unit, turn the power off and immediately

disconnect the power cord. Remove the material and contact an authorized service

representative if damage has occurred.

[Transportation]

Handle with care to avoid

impact shock during transit, which may cause

malfunction. When you need to transport the unit, use the original or suitable

alternative packing material.

Stop

Caution

Hazard

MHazard

Caution

Hazard

Caution

[Circuitry Access]

Do not remove covers, panels, casing, or access the circuitry with power applied to

the unit. Turn the power off and disconnect the power cord prior to removal. Internal

servicing / adjustment of unit should only be performed by qualified personnel.

Do not touch any parts / circuitry with a high heat factor.

Capacitors can retain enough electric charge to cause mild to serious shock, even

after the power has been disconnected. Capacitors associated with the power

supply are especially hazardous.

Unit should not be operated or stored with cover, panels, and / or casing removed.

Operating the unit with circuitry exposed could result in electric shock / fire hazards

or a unit malfunction.

[Potential Hazards]

If abnormal odors or noises are noticed coming from the unit, immediately turn the

power off and disconnect the power cord to avoid potentially hazardous conditions.

If problems similar to the above occur, contact an authorized service representative

before attempting to operate the unit again.

[Rack Mount Brackets, Ground Terminal, and Rubber Feet]

To rack-mount or ground the unit, or to install rubber feet, do not use screws or

materials other than those supplied. Doing so may cause damage to the internal

circuits or components of the unit. If you remove the rubber feet that are attached to

the unit, do not reinsert the screws that secure the rubber feet.

[Consumables]

Consumable items that are used in the unit must be periodically replaced. For

further details on which parts are consumables and when they should be replaced,

refer to the specifications at the end of the Operation Manual. Since the service life

of the consumables varies greatly depending on the environment in which they are

used, such items should be replaced at an early date. For details on replacing

consumable items, contact your dealer.

Caution

Hazard

Stop

Caution

Upon Receipt

Unpacking

FA-AUX30 units and their accessories are fully inspected and adjusted prior to shipment.

Operation can be performed immediately upon completing all required connections and

operational settings.

Check your received items against the packing lists below. Check to ensure no damage has

occurred during shipment. If damage has occurred, or items are missing, inform your supplier

immediately.

ITEM QTY REMARKS

FA-AUX30 1

Rack Mount Brackets 1 set EIA standard type

Control Cable 3 sets For FA-10GPI or FA-10RU connection (1m)

CD-ROM 1 FA-AUX30 Operation Manual (PDF)

Button Labels 1 set

Pry tool 1 For button cap removal

Attaching Button Labels

Use the supplied pry tool and button label.

Removing button switches

(1)Slide the pry tool into the opening between a button

and front panel casing (with the lip of the tool facing

the button).

IMPORTANT

Slide the pry tool to the right or left of a button, not above or below, to prevent damage

to the unit.

(2)Wedge the lip of the pry tool under the button.

(3)Pry the button out.

(4)Completely remove the button.

Pry lever

Removing Button Caps

Wedge a corner of the pry tool into a side slot along the bottom of a button

cap to remove the cap.

* If the button cap is firmly attached, and cannot be easily removed,

alternately wedge the tool into both side slots to remove the cap.

Attaching Button Labels and Button Caps

(1)Carefully place a button cap over a label aligning the

slots as shown to the right.

(2)Make sure the (right) hook is facing right, then allign the button

tabs and cap slots accordingly. Refer to the figure below showing

the difference between the hooks (left/right).

IMPORTANT

Button switches cannot be installed onto the switch unit

unless they are properly

oriented.

Slot

Button label

Hook (right)

Offset

Hook (left)

Centered.

Right

Left

Left and right button hooks

Slot

Tab

Hook(right)

Reinstalling Button Switches

(1)Verify that the (right) and (left) hooks properly align with the switch unit notches as shown

below.

(2)Insert the button switch into the switch unit until it clicks.

IMPORTANT

Inserting a button switch in an incorrect orientation may damage the switch units. Be

sure to orient the button switches correctly.

Label attachment is now complete.

Switch unit

Button switch

Hook (left)

Notch (left)

Switch unit

Button switch

Hook (right)

Notch (right)

1. Prior to Starting ........................................................................................................................9

1-1. Welcome ...........................................................................................................................9

1-2. Features............................................................................................................................9

2. Panel Descriptions .................................................................................................................10

2-1. Front Panel......................................................................................................................10

2-2. Rear Panel ......................................................................................................................10

2-3. GPI 1 to 3........................................................................................................................11

2-4. Setting LED Button Colors ..............................................................................................12

3. Connection.............................................................................................................................14

3-1. Connection Conditions .................................................................................................... 14

3-2. Connecting with the FA-10RU.........................................................................................14

3-3. Connecting with the FA-10GPI........................................................................................14

3-4. Powering On....................................................................................................................14

4. Specifications and Dimensions...............................................................................................15

4-1. Specifications..................................................................................................................15

4-2. Control Cable Specifications ........................................................................................... 15

4-3. External Dimensions .......................................................................................................16

Appendix Button Labels ...............................................................................................................1

1. Prior to Starting

1-1. Welcome

Congratulations! By purchasing an FA-AUX30 Auxiliary Unit you have entered the world of

FOR-A and its many innovative products. Thank you for your patronage and we hope you will

turn to FOR-A products again and again to satisfy your video and audio needs.

FOR-A provides a wide range of products, from basic support units to complex system

controllers, which have been increasingly joined by products for computer video-based systems.

Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing

service to you.

1-2. Features

The FA-AUX30 is a remote control unit that controls FA-1010 and FA-10RU GPI input and

output.

Assigning often-used functions to the FA-AUX30 button switches can simplify and quicken

operational procedures.

Can be used by connecting to an FA-10GPI option on FA-1010 units, or an FA-10RU.

Simple connection using 3 GPI cables (Power also supplied via GPI cables)

Selectable LED button colors (red, green, orange)

2. Panel Descriptions

2-1. Front Panel

No. Name Description

1 DC POWER Indicator lights when power is supplied from the FA-1010 or FA-10RU.

2-2. Rear Panel

No. Name Description

1 GPI 1 Used to connect to the FA-10RU or FA-10GPI.

2 GPI 2

3 GPI 3

4 LED COLOR Used to select the front panel LED button colors.

GPI1 GPI2 GPI3

DC POWER

FA-AUX30

AUXILIARY UNIT

Table des matières

Autres manuels FOR-A Télécommande

FOR-A

FOR-A FA-95RU Manuel utilisateur

FOR-A

FOR-A MV-42HS Manuel utilisateur

FOR-A

FOR-A USF-105AS Manuel utilisateur

FOR-A

FOR-A LTS-10GR Manuel utilisateur

FOR-A

FOR-A FA-95RU Manuel utilisateur