Fluke SPOT Light Manuel utilisateur

PN 4151274

February 2012 | Rev. 2, 1/22

All product names are trademarks of their respective companies.

SPOT Light

SpO2 Functional Tester

Warranty and Product Support

Fluke Biomedical warrants this instrument against defects in materials and workmanship for two years from the date of

original purchase. You will be charged our customary fee for such calibration. During the warranty period, we will repair or at

our option replace, at no charge, a product that proves to be defective, provided you return the product, shipping prepaid, to

Fluke Biomedical. This warranty covers the original purchaser only and is not transferable. The warranty does not apply if

the product has been damaged by accident or misuse or has been serviced or modified by anyone other than an authorized

Fluke Biomedical service facility. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE

EXPRESSED OR IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY.

This warranty covers only serialized products and their accessory items that bear a distinct serial number tag. Recalibration

of instruments is not covered under the warranty.

This warranty gives you specific legal rights and you may also have other rights that vary in different jurisdictions. Since

some jurisdictions do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages,

this limitation of liability may not apply to you. If any provision of this warranty is held invalid or unenforceable by a court or

other decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

7/07

Notices

system, or translated into any language without the written permission of Fluke Biomedical.

Fluke Biomedical agrees to a limited copyright release that allows you to reproduce manuals and other printed materials for use in service

training programs and other technical publications. If you would like other reproductions or distributions, submit a written request to Fluke

Biomedical.

Unpacking and Inspection

Follow standard receiving practices upon receipt of the instrument. Check the shipping carton for damage. If damage is found, stop unpacking

the instrument. Notify the carrier and ask for an agent to be present while the instrument is unpacked. There are no special unpacking

instructions, but be careful not to damage the instrument when unpacking it. Inspect the instrument for physical damage such as bent or

broken parts, dents, or scratches.

Technical Support

For application support or answers to technical questions, either email [email protected] or call 1-800- 850-4608 or 1-440-

248-9300. In Europe, call +31-40-2675314.

Claims

Our routine method of shipment is via common carrier, FOB origin. Upon delivery, if physical damage is found, retain all packing materials in

their original condition and contact the carrier immediately to file a claim. If the instrument is delivered in good physical condition but does not

operate within specifications, or if there are any other problems not caused by shipping damage, please contact Fluke Biomedical or your local

sales representative.

Returns and Repairs

Return Procedure

All items being returned (including all warranty-claim shipments) must be sent freight-prepaid to our factory location. When you return an

instrument to Fluke Biomedical, we recommend using United Parcel Service, Federal Express, or Air Parcel Post. We also recommend that

you insure your shipment for its actual replacement cost. Fluke Biomedical will not be responsible for lost shipments or instruments that are

received in damaged condition due to improper packaging or handling.

Use the original carton and packaging material for shipment. If they are not available, we recommend the following guide for repackaging:

Use a double–walled carton of sufficient strength for the weight being shipped.

Use heavy paper or cardboard to protect all instrument surfaces. Use nonabrasive material around all projecting parts.

Use at least four inches of tightly packed, industry-approved, shock-absorbent material around the instrument.

Returns for partial refund/credit:

Every product returned for refund/credit must be accompanied by a Return Material Authorization (RMA) number, obtained from our Order

Entry Group at 1-440-498-2560.

Repair and Calibration:

For customers based in the U.S.A., please contact Fluke Electronics at globalcal@flukebiomedical.com, or call 1-833-296-9420.

All other customers, please go to www.flukebiomedical.com/service to find the nearest service center.

Certification

This instrument was thoroughly tested and inspected. It was found to meet Fluke Biomedical’s manufacturing specifications when it was

shipped from the factory. Calibration measurements are traceable to the National Institute of Standards and Technology (NIST). Devices for

which there are no NIST calibration standards are measured against in-house performance standards using accepted test procedures.

WARNING

Unauthorized user modifications or application beyond the published specifications may result in electrical shock hazards or improper

operation. Fluke Biomedical will not be responsible for any injuries sustained due to unauthorized equipment modifications.

Restrictions and Liabilities

Information in this document is subject to change and does not represent a commitment by Fluke Biomedical. Changes made to the

information in this document will be incorporated in new editions of the publication. No responsibility is assumed by Fluke Biomedical

for the use or reliability of software or equipment that is not supplied by Fluke Biomedical, or by its affiliated dealers.

Manufacturing Location

The SPOT Light SpO2 Functional Tester is manufactured at Fluke Biomedical, 6920 Seaway Blvd., Everett, WA, U.S.A.

Table of Contents

Title Page

Introduction .................................................................................................................... 1

Intended Use .................................................................................................................. 2

Safety Information .......................................................................................................... 2

Unpack the Product........................................................................................................ 3

Instrument Familiarization .............................................................................................. 4

Accessories.................................................................................................................... 5

How to Turn On the Product........................................................................................... 6

How to Use the Product ................................................................................................. 6

SpO2 Sensor Placement ........................................................................................... 6

How to Set Test Parameters ..................................................................................... 8

How to Set Custom Tests............................................................................................... 9

Maintenance................................................................................................................... 10

How to Clean the Product.......................................................................................... 11

Battery Maintenance.................................................................................................. 11

How to Charge the Battery ................................................................................... 11

SPOT Light

Users Manual

Battery Removal................................................................................................... 13

General Specifications................................................................................................... 14

Detailed Specifications .................................................................................................. 14

Oximeter SpO2Optical Emitter and Detector ............................................................ 14

iii

List of Tables

Table Title Page

1. Symbols................................................................................................................................. 2

2. Product Controls and Connections........................................................................................ 4

3. Standard Accessories ........................................................................................................... 5

4. Optional Accessories............................................................................................................. 5

5. Test Parameters.................................................................................................................... 8

SPOT Light

Users Manual

Table des matières

Autres manuels Fluke Équipement de test

Fluke

Fluke DTX Series Manuel d'utilisation et d'entretien

Fluke

Fluke T90 Manuel utilisateur

Fluke

Fluke 105B Manuel utilisateur

Fluke

Fluke ScopeMeter 123 Manuel utilisateur

Fluke

Fluke NetTool Manuel utilisateur

Fluke

Fluke 5700A Series II Service Manuel utilisateur

Fluke

Fluke 9170 Manuel utilisateur

Fluke

Fluke 714B/EN Manuel utilisateur

Fluke

Fluke 5440B/AF Manuel utilisateur

Fluke

Fluke CableIQ CIQ-100 Manuel utilisateur

Fluke

Fluke 4180ETRS Manuel utilisateur

Fluke

Fluke 5560A Manuel utilisateur

Fluke

Fluke 721-1601 Manuel d'utilisation et d'entretien

Fluke

Fluke MicroNetBlink Kit Manuel utilisateur

Fluke

Fluke 1621 Manuel utilisateur

Fluke

Fluke i400 Manuel d'utilisation et d'entretien

Fluke

Fluke 9009 Manuel utilisateur

Fluke

Fluke TS 120 Manuel utilisateur

Fluke

Fluke FiberInspector Pro FI-3000 Manuel utilisateur

Fluke

Fluke 150 Series Manuel d'utilisation et d'entretien

Fluke

Fluke 975 AirMeter Instructions d'installation et d'utilisation

Fluke

Fluke 1AC II VoltAlert Manuel utilisateur

Fluke

Fluke CNX a3000 Manuel utilisateur

Fluke

Fluke ScopeMeter 196 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur