Flexco Clipper Pro 200 Manuel utilisateur
Pro 200
OPERATION MANUAL
This instruction book contains the operating
instructions for the two styles of Pro 200 Lacing
Machines. Many of the steps required to operate
these machines are similar. However, when
necessary these steps will be separated.
Pro 200
Pro 200 EH
Table of Contents
i
OPERATING INSTRUCTIONS
Machine Preparation - Pro 200 and Pro 200 EH................................................................1
Belt Preparation..................................................................................................................2
Selecting and Installing the Proper Adapter/Comb.............................................................3
Selecting the Correct Size Gauge Pin................................................................................4
Determining the Number of Hooks Required......................................................................4
Inserting Hooks, Gauge Pin and Belt .................................................................................4
Determine the Correct Pressure and Gauge Pin - Pro 200 and Pro 200 EH .....................6
Removing the Belt/Hook Assembly from Machine..............................................................7
Carding Paper Removal .....................................................................................................8
Installing Hooks on Belt Ends Requiring More Than One Strip of Hooks...........................8
Appendix
ii
Troubleshooting..................................................................................................................9
Suggested Workbench Setup - Side View..........................................................................10
Suggested Workbench Setup - Front View ........................................................................11
Pro 200 Parts Drawing........................................................................................................12
Pro 200 Spare Parts List.....................................................................................................13
Log Sheet ...........................................................................................................................16
• Place the machine on a solid
work surface. We recommend
that you construct a work bench.
Recommendations are made on
Pages 10 and 11.
• Remove the cap from the hydraulic
uid reservoir located in the foot pump
and ll if necessary.
• Unwrap the hydraulic hose and
connect the foot pump to the lacing
machine.
• Be careful not to set anything on the hydraulic hose. Doing so can pinch off the hose or
rupture it, causing it to leak.
• Do not close the jaws without an adapter in place.
Machine Preparation - Foot Pump Setup
Machine Preparation - Pro 200 EH Pump Setup
1
Cap
Hydraulic
Hose
Connection
• Remove the protective cap from the adjusting screw (Fig. 1).
• Loosen the Breather Cap on pump (Fig. 1).
• Connect the hydraulic pump to the lacer via the quick connect coupling (Fig. 2).
Adj. Screw
Lock Nut
Breather Cap
FIG. 1
Coupling
FIG. 2
Jaw
1. Cut belt using the center-line cutting method to ensure
a square cut. Follow the instructions below:
a. Prior to any work on your conveyors, make certain
that the power has been turned off and the belt is
“locked out”.
b. Mark the actual center points in belt width at
intervals of 3 to 5 feet, for a distance of 15 to 20 feet
back from the intended splice area (Fig. 1).
c. Using either a steel rule or a chalk line, mark the
average center line through the points measured in
Step 2 (Fig. 2).
d. Using a square, draw a line perpendicular to the
average center line across the belt width (Fig. 2).
e. Using the Clipper®845LD Cutter, cut the belt on the
line drawn in Step 4.
2. Skive impression cover off from the belt ends that will
be laced, if applicable. Skive back 3/4" (Fig. 3).
3. Select the proper hook for the belt/application. If the
belt has an impression cover it is important to select
the hook based on the thickness of the skived portion.
Belt Preparation
FIG. 3
FIG. 1
FIG. 2
2
The adapter you will need is determined by the hook you have selected for your application.
Below is a chart displaying hook sizes and their corresponding adapters, gauge pins and
hinge pins.
Selecting and Installing the Proper Adapter/Comb
Installing the Adapter
Insert one end of the adapter into the jaws of
the machine, and push down until it bottoms
out (Fig. 4). If necessary, squeeze the
adapter together slightly while performing
this operation. If you prefer to apply lacing
to the belt from left to right, position the extra
deep slots/transfer section to the left of the
machine. Lacing the belt from right to left
requires placing the transfer section to the
right of the machine.
Drop the remainder of the adapter into place,
using caution to avoid pinching ngers
(Fig. 5).
3
FIG. 4 FIG. 5
FIG. 6
NOTE: When repeated use is called for, the
adjusting cam (Pro 200) can be adjusted so
that the jaws provide adequate clearance to
remove carding paper but are close enough
together to reduce jaw cycle time.
Adjust the cam if the adapter will not t into
place, or if it is too loose (Fig. 6).
HOOK SIZE PRO 200 ADAPTER GAUGE PINS (mm)
#25 P2CLPR25 1.5, 1.8x1.5, 2.0x1.5
#36 / #30 P2CLPR36/30 1.5, 1.8x1.5, 2.0x1.5
#1 P2CLPR1 1.8, 2.0, 2.5x2.0, 3.0x2.0
#2 - #7 P2C2 2.5, 3.5x3.0, 4.0x3.0
The Pro 200 Lacer offer multiple size gauge pins to achieve an optimal loop prole. Select
a gauge pin that is 20% to 30% thinner than your belt thickness.
Selecting the Correct Size Gauge Pin
Lay strips of hooks end-to-end across the entire width of your
belt, leaving 1/4" of belt open on each side for notching. When
it is necessary to cut a strip of hooks, cut only one strip.
The trailing end of the belt should have one less hook than the
leading end. This is to prevent hooks from getting caught on the
conveyor framework and pulling out. The trailing end should also
be notched/tapered so as to prevent belt rips or tearing.
Determine the Number of Hooks Required
Practice on a sample piece of belt, making sure the piece is from the same belt you intend to
splice. This sample piece should ideally be 6" wide. If your belt is less than 6" wide use the
narrower measurement. Install sample splice(s) to determine the proper pressure required to
set the hooks. (Lacing procedures begin on page 6). Record your results on the piece of belt
and also in the log at the end of this booklet. Refer to this log whenever you splice this belt to
avoid repeated experimentation.
Remember, the purpose for offering multiple gauge pin diameters is to eliminate the keyhole
shaped loop and to provide the best possible hook set for optimum performance. If a keyhole
shaped loop is produced, change the gauge pin to the next smaller size and apply new hooks
to your sample.
Inserting Hooks, Gauge Pin and Belt
Center the shortest strip of hooks in the adapter
rst. Failure to center the strip may cause the
machine to apply unequal pressure to the jaws,
jamming the machine.
When installing full (6") strips of hooks, place
one end hook into the slot adjacent to the transfer
section (Fig. 7).
NOTE: Do not place unset hooks in the
transfer section at any time.
Extra Deep Slots/
Transfer Section
4
FIG. 7
Insert the gauge pin at side up (if applicable)
into the hole in the comb opposite the transfer
section and push it in completely. If using
carded hooks as shown in Fig. 8, remove
carding paper at this time. If installing Unibar®
fasteners as shown in Fig. 9, remove safety
strip now. If using carded hooks as shown in
Fig. 10, the paper is removed after hooks are
installed.
Insert the belt between the points of the hooks
and push it down against the comb (Fig. 11).
When installing hooks in belts 6" wide or less
be sure to center the hooks on the belt leaving
1/4" protruding from each end of the strip of
hooks. This allows for notching the trailing end
of the belt (Fig. 12).
When installing hooks into a belt wider than 6"
(requiring two or more strips of hooks), leave
1/4" of belt protruding past the last hook near
the transfer section.
FIG. 8 FIG. 9 FIG. 10
5
FIG. 11
FIG. 12
Pump the footpump until the jaws of the machine rst come in contact with the belt. Note
the pressure reading on the pressure gauge.
PRO 200 USERS:
Determine the correct pressure and gauge pin required for your
application
Release the pressure by turning the control knob of
the release valve counterclockwise until the jaws
retract completely. Turn the control clockwise until
snug. Do not overtighten this valve (Fig. 13).
Inspect lace for proper set down. (See Page 7).
If splice is not installed enough, repeat process,
bring pressure up higher. Continue process until
proper setdown is achieved.
6
FIG. 13
Control
Knob
1) Press the foot pedal to cycle the machine while
observing the pressure gauge on the
Pro 200 lacer (Fig. 14).
2) Loosen the lock nut (Fig. 15).
3) Adjust to the desired pressure by turning
the adjusting screw. Turn the adjusting screw
clockwise to increase the pressure and counter
clockwise to decrease the pressure. The maximum
pressure attainable by the pump is pre-set to 6500
PSI (Fig. 15).
4) Once the desired pressure is achieved, tighten
the lock nut to hold the setting (Fig. 15).
Note: The Pro 200 Electric Hydraulic lacer is
factory set at the maximum speed. If a slower
speed is desired, a ow control valve can be
placed in the hydraulic line that connects the
electric hydraulic pump to the Pro 200 lacer.
PRO 200 EH USERS:
Gauge
Adj. Screw
Lock Nut
FIG. 14
FIG. 15
Correct set is achieved when one half to one third of the wire
diameter of the hook is imbedded into the belt surface without
a keyhole shaped loop and the points are just visible from the
opposite side of the belt (Fig. 14).
Repeat the above procedures, increasing the pressure
slightly until proper set is achieved.
If the loop has a keyhole shape, reapply new hooks using
the next smaller gauge pin.
The hook points should be slightly visible on the opposite
side of the belt. If the points are protruding through and
curling over excessively, the hook is too large. Resplice
using a smaller hook size.
FIG. 14
Optimal Splice
Removing Belt/Hook Assembly from Machine
Pull the gauge pin completely out of the comb by pulling it straight out without bending or
twisting it. Twisting the gauge pin can break the handle off the gauge pin. If necessary,
push the belt back and forth to loosen the gauge pin.
Pull the belt straight up and out of the machine. Do
not twist the belt as it is removed (Fig. 15).
Example: You nd that one 6" strip of hooks requires 250 bars pressure to properly set in a
particular belt. Applying one 3" strip of hooks of the same size in the same belt requires that
the pressure be reduced 50%, to 125 bars.
FIG. 15
Once you have determined the correct requirements for your belt, further experimentation
becomes unnecessary. Enter this data in your log book and use it as a reference when
splicing this belt in the future.
7
Do not change the pressure setting if you will be
making additional splices on the same belt. The
pressure setting as well as the gauge pin will be
used on future applications to this belt. However,
splicing a different width piece of the same belt
may require changing the pressure.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Flexco Équipement industriel
