Flash LED FRAME 700W Manuel utilisateur
User Manual
Instrukcja Obsługi
F7100751
LED FRAME 700W
(EN) THANK YOU FOR PURCHASING THIS FLASH-BUTRYM
PRODUCT. BEFORE BEGINNING TO OPERATE THIS UNIT, PLEASE
READ THE INSTRUCTIONS CAREFULLY TO ENSURE THE BEST
POSSIBLE PERFORMANCE.
(PL) DZIĘKUJEMY ZA ZAKUP PRODUKTU FLASH-BUTRYM. PRZED
ROZPOCZĘCIEM OBSŁUGI TEGO URZĄDZENIA NALEŻY UWAŻNIE
PRZECZYTAĆ INSTRUKCJĘ, ABY ZAPEWNIĆ NAJLEPSZĄ MOŻLIWĄ
WYDAJNOŚĆ.
Please keep this User Manual for future
consultation. If you sell the xture to another
user, be sure that they also receive this
instruction booklet.
Unpack and check carefully there is no
transportation damage before using the xture.
Before operating, ensure that the voltage and
frequency of power supply match the power
requirements of the xture.
It’s important to ground the yellow/green
conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and
maintenance.
Use safety chain when xes this xture. Don’t
handle the xture by taking its head only, but
always by taking its base.
Maximum ambient temperature is: 40°C Don’t
operate it where the temperature is higher than
this.
WARNING! The Led Moving Head (LMH) has a powerful pan motor. The torque reaction when
the head is panned suddenly can cause the base to move if the fixture is standing unsecured on
a surface. Do not apply power to the LMH unless the baase is securely fastened to a surface or to
rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock
each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 90clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with
the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of
clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any
other strong light source from any angle - even for a few seconds. See Figure 1. The LMH lens
can focused the sun's rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LMH, as intense
illumination can damaged the display.
In the event of serious operating problem,
stop using the xture immediately. Never try
to repair the xture by yourself. Repairs carried
out by unskilled people can lead to damage
or malfunction. Please contact the nearest
authorized technical assistance center. Always
use the same type spare parts.
Do not connect the device to any dimmer
pack.
Do not touch any wire during operation and
there might be a hazard of electric shock.
To prevent or reduce the risk of electrical
shock or re, do not expose the xture to rain
or moisture.
The housing must be replaced if they are
visibly damaged.
Do not look directly at the LED light spot while
the xture is on.
2. SAFETY INFORMATION
1. INTRODUCTION
THANK YOU FOR PURCHASING LED FRAME 700W. FOR SAFETY REASONS AND TO
ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.
User Manual • Instrukcja Obsługi
Figure 1. Lenses can focused sunlight and strong light, presenting a risk of fire and damage to the fixture.
Shield or shade the head if necessary.
WARNING
LED FRAME 700W • Art No F7100751
The unit should be mounted via its screw
holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration
and slipping while operating. Always
ensure that the structure to which you are
attaching the unit is secure and is able to
support a weight of 10 times of the unit’s
5.1 Connecting DMX signal
The connection is performed using cable with
XLR-female -> XLR-Male plugs.
4. INSTALLATION
5. CONNECTION
3. PRODUCT INFORMATION
weight. Also always use a safety cable
that can hold 12 times of the weight of
the unit when installing the fixture. The
equipment must be fixed by professionals.
And it must be fixed at a place where is
out of the touch of people and has no one
pass by or under it.
The device is equipped with the following
interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): powerCON socket
CAUTION! At the last xture, the
DMX signal has to be terminated with
a terminator. Solder a resistor
between signal (-) and signal (+) into a
XLR plug and plug it in the DMX output of
the last xture.
1
3
22
FEMALE
XLR
GROUND
DMX +
DMX -
MALE
XLR
3
1
3-pin XLR
1
FEMALE
XLR
GROUND
DMX +
DMX -
MALE
XLR
2
3
4
5
1
2
3
45
5-pin XLR
Light Source: 1 Standard LED (Single color)
Power consumption: 700W
Power supply voltage: 110-240V,
50/60Hz AC
PAN range: 540°
TILT range: 270°
Beam angle (min/max): 5°-55°
Color: 8000K, Color wheel - 7 colors
+ white (open)
Zoom: Yes
Focus: Electronic
Gobo wheel: Roto Gobo: (6 interchangeable
gobos, 1 xed gobo, 1 empty) indexed,
Fixed Gobo: (8 interchangeable gobos,
1 empty) indexed
Prism: 3-wall prism, 6-sided linear prism
(can work together at the same time)
Flash frequency min./max: 0-20Hz
Features: Linear CRI lter from 68 to 90
CRI. Animation wheel: Dynamic ame or
water effect with no rotation limit,
indexed. CTO.
Framing: 4 knives + 90 degrees rotation
mounted close to each other, which
means that you can sharpen each knife at
the same time
Operating modes: DMX 512, RDM, Artnet
(Optional), Auto-running, Master/Salve,
Sound active, Built-in program
Frost lter: Yes
36 DMX channel mode.
IP Rating: IP20
Housing made: ABS
Cooling: Active
AC IN/OUT: powerCON IP65
3-Pin XLR DMX Input/Output
Net Weight: 36kg
Dimensions: H(90,5)xW(56)xD(45,5) cm
Weight: 6 kg
The connection is performed using
power cable with PowerCon connector
(included). The device must be
operated by qualified personnel.
1. Press „Menu” to „Set DMX Address”,
and press „ENTER” keys to enter into.
2. Show „Set DMX Address DMX Address:
001”, Press the „UP and DOWN” keys to
amended.
5.2 Voltage specification
5.5 Set DMX Address Code
Input Voltage Total Power Frequency
110~240V AC 700W 50/60Hz
5.3 Connecting power supply
CAUTION! In the case of cable damage do not attempt to repair.
Replacement or repair can be made only on the manufacturer or by
a person with appropriate permissions.
Make sure that the power grid supply
parameters are consistent with device
parameters and limitations are not exceeded.
Using lamp, the change rate of power voltage should be within
±10%, if the voltage is too high, it will shorten the light’s life; if it’s not
enough, the lamp will be dark. Please restart it after turning off light
for 20 minutes until full-cooling. Frequent switching will reduce the
life span of lamps and bulbs; intermittent using will improve the life
of bulbs and lamps.
3. Press „ENTER” keys to save and Exit,
Press the „MENU” Keys does not save
and Exit.
DMX
Controller DMX 512 DMX 512 120
User Manual • Instrukcja Obsługi
6. DMX CHANNELS
36 CH Mode
CH Function Value Description
1PAN 0-255 0-540
2 PAN Fine 0-255 0-2
3 Tilt 0-255 0-270
4 Tilt Fine 0-255 0-1
5 Pan/Tilt Speed 0-255 From Fast » Slow
6 Strobe 0-3 OFF
4-127 Pulse Strobe from Slow » Fast
128-191 Gradual Strobe from Slow » Fast
192-251 Random Strobe from Slow » Fast
252-255 ON
7 Dimmer 0-255 0-100% Linear Dimmer
8 C 0-255
9 M 0-255
10 Y 0-255
11 CTO 0-255
12 Color 0-127 Linear Color
128-137 Red
138-146 Green
147-155 Blue
156-164 Yellow
165-173 Magenta
174-182 Orange
183-191 Pink
192-222 Clockwise color effect Fast » Slow
223-224 STOP
225-255 Anticlockwise color effect from Slow » Fast
13 CRI 0-79 Mover away
80-255 Insert
LED FRAME 700W • Art No F7100751
CH Function Value Description
14 Fixed Gobo 0-9 White (OPEN)
10-19 Gobo 1
20-29 Gobo 2
30-39 Gobo 3
40-49 Gobo 4
50-59 Gobo 5
60-69 Gobo 6
70-79 Gobo 7
80-89 Gobo 8
90-99 Gobo 1 (Shake)
100-109 Gobo 2 (Shake)
110-119 Gobo 3 (Shake)
120-129 Gobo 4 (Shake)
130-139 Gobo 5 (Shake)
140-149 Gobo 6 (Shake)
150-159 Gobo 7 (Shake)
160-169 Gobo 8 (Shake)
170-212 Gobo rotation Clockwise Fast >> Slow
213-215 STOP
216-255 Gobo rotation Anticlockwise Slow >> Fast
15 Rotation Gobo 0-9 White (Open)
10-19 Rot. Gobo 1
20-29 Rot. Gobo 2
30-39 Rot. Gobo 3
40-49 Rot. Gobo 4
50-59 Rot. Gobo 5
60-69 Rot. Gobo 6
70-79 Rot. Gobo 1 (Shake)
80-89 Rot. Gobo 2 (Shake)
90-99 Rot. Gobo 3 (Shake)
100-109 Rot. Gobo 4 (Shake)
User Manual • Instrukcja Obsługi
CH Function Value Description
110-119 Rot. Gobo 5 (Shake)
120-129 Rot. Gobo 6 (Shake)
130-190 Rot. Gobo rotation Anticlockwise Fast>>Slow
191-192 STOP
193-255 Rot. Gobo rotation Anticlockwise Slow>>Fast
16 Indexed Gobo Rot. 0-127 Indexde Gobo Rotation
128-190 Clockwise Rotation Fast >> Slow
191-192 STOP
193-255 Anticlockwise Rotation Slow >> Fast
17 Effect Insert 0-255
18 Effect Rotation 0-128 Anticlockwise Eff. Rotation Slow >> Fast
129-255 Clockwise Eff. Rotation Slow >> Fast
19 Focus 0-255
20 Focus ne 0-255
21 Zoom 0-255
22 Prism 1 0-63 Empty
64-127 Prism 1
128-191 Prism 2
192-255 Prism 1 + Prism 2
23 Prism 1 Rotation 0-127 Prism Indexed
128-187 Prism Rotation Clockwise Fast >> Slow
188-195 STOP
196-255 Prism Rot. Anticlockwise Slow >> Fast
24 Prism 2 Rotation 0-127 Prism Indexed
128-187 Prism Rotation Clockwise Fast >> Slow
188-195 STOP
196-255 Prism Rot. Anticlockwise Slow >> Fast
25 Frost 0-127 Frost OFF
128-255 Frost ON
26 Blade 1 0-255 Linear Insert - Left Top
27 Blade 2 0-255 Linear Insert - Left Down
LED FRAME 700W • Art No F7100751
User Manual • Instrukcja Obsługi
CH Function Value Description
28 Blade 3 0-255 Linear Insert - Right Down
29 Blade 4 0-255 Linear Insert - Right Top
30 Blade 5 0-255 Linear Insert - Top Left
31 Blade 6 0-255 Linear Insert - Top Right
32 Blade 7 0-255 Linear Insert - Down Left
33 Blade 8 0-255 Linear Insert - Down Right
34 Blade wheel 0-255 Blades Rotation Anticlockwise
35 Iris 0-127 Indexed Open >> Close
128-255 Speed Pulse Close >> Open (Slow >> Fast)
36 Function 0-209 Empty
210-219 Reset XY after 3 sec.
220-235 Reset effect motor after 4 sec.
240-255 Reset whole unit after 5 sec.
LED FRAME 700W • Art No F7100751
User Manual • Instrukcja Obsługi
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Flash Matériel de DJ
Flash
Flash F7100322 Manuel utilisateur
Flash
Flash F7300240 Manuel utilisateur
Flash
Flash LED Spyder Mini Manuel utilisateur
Flash
Flash RGBWAUV Manuel utilisateur
Flash
Flash F7100086 Manuel utilisateur
Flash
Flash F7300215 Manuel utilisateur
Flash
Flash LED PAR 56 7X15W RGBWA+UV 6IN1 Manuel utilisateur
Flash
Flash F5100347 Manuel utilisateur
Flash
Flash P7200045 Manuel utilisateur
Flash
Flash F7100109 Guide produit
Flash
Flash F5300003 Manuel utilisateur
Flash
Flash F7000543 Manuel utilisateur
Flash
Flash FL-202 BEAM 5R Manuel utilisateur
Flash
Flash F7300248 Manuel utilisateur
Flash
Flash F7100520 Manuel utilisateur
Flash
Flash LIGHT BOX MOON 1 Manuel utilisateur
Flash
Flash LED MOVING HEAD 60W Manuel utilisateur
Flash
Flash F7200177 Manuel utilisateur
Flash
Flash F7100498 Manuel utilisateur
Flash
Flash LED Spyder Mini Moving Head 8x15W 4in1 RGBW- No Limit... Manuel utilisateur
Manuels Matériel de DJ populaires d'autres marques
thomann
thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur
Eagletone
Eagletone 6 Eyes Flower Manuel utilisateur
EuroLite
EuroLite FLD-1508 Manuel utilisateur
Technical Pro
Technical Pro LG8xSEA Manuel utilisateur
JB Systems
JB Systems Lounge Laser DMX Manuel utilisateur
Lightmaxx
Lightmaxx Vega Halo 90 Manuel utilisateur
Elation
Elation FUZE WASH Z350 Manuel utilisateur
Maverick
Maverick MK3 WASH Manuel utilisateur
Infinity
Infinity TF-260C7 Fresnel Manuel utilisateur
Chauvet
Chauvet EVE E-50Z Manuel utilisateur
Eliminator Lighting
Eliminator Lighting E 138 Manuel utilisateur
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur