Fitel S327 Manuel utilisateur

FTS-B616

Issue 1; Feb. 2023

S327 Precision Cleaver

Operating Instructions

・Please read this entire manual prior to using the S327 Precision Cleaver.

・This manual must be kept with the S327 Precision Cleaver.

Safety Instructions

This manual contains the complete operating and basic maintenance

instructions for the S327 Precision Cleaver.

Please review this manual carefully before using the S327 Precision Cleaver.

The following safety instructions must be followed whenever this product is

operated, serviced, or repaired. Failure to comply with any of these instructions

or with any precaution or warnings contained in this manual is in direct

violation of the standards of the design, the manufacturer, and the intended use

of the instrument. FURUKAWA ELECTRIC CO., LTD. assumes no liability

for the customer’s failure to comply with these requirements.

Safety Instructions

CAUTION

Failure to comply with any of the instructions,

which are indicated by this symbol, may cause

serious injury or damage to the machine.

ATTENTION

Failure to comply with any of the instructions,

which are indicated by this symbol, may cause the

device to function improperly and degrade the

performance.

Please contact FURUKAWA ELECTRIC CO., LTD. with any questions

relating to the description of this manual.

In no case will FURUKAWA ELECTRIC CO., LTD. be liable to the buyer, for

any consequential or indirect damage which is caused by product failure,

malfunction, or any other problem.

CAUTION

・Avoid soaking the S327 with water. Doing so may cause malfunction.

・This product is a precision machine. Do not drop, throw, or handle it roughly.

Doing so may cause machine’s malfunction.

・Do not use in a humid, dirty, or unstable environment. Doing so may cause

malfunction.

・Please be cautious when disposing of fibers from the fiber waste bin.

Scattered fibers may cause injury.

・The fiber waste bin for loose fiber must be installed into the S327 Precision

Cleaver during operation, otherwise there is a risk of loose fibers scattering.

ATTENTION

・Use an appropriate tool when loosening or tightening the set screw to fix the

single fiber adapter to the unit and gently tighten the screw.

・Please clean the fiber with alcohol after stripping the coating material before

setting it on to S327 Precision Cleaver.

・Do not use acetone or other organic solvents to clean the rubber.

・Do not use lubricants for maintenance of this product.

・Do not use organic solvent such as acetone to clean the rubber pads.

1.Standard Components

Parts Name

Parts No.

Qty

S327 Main Body

S327A-01

Single Fiber Adapter

S327X-18

Waste Bin

S327X-12

Carrying Case

S327X-17

Hexagonal Wrench

S327X-16

Operating Instructions

FTS-B616

2.Optional Components

Parts Name

Parts No.

Qty

Blade Exchange Set

S327X-24

Single Fiber Adapter

S327X-18

Carrying Case

S327X-17

Waste Bin

S327X-12

3.External Desctiption

4.Specifications

Applicable Fiber

Silica

Fiber Count

Single Fiber

Ribbon Fiber (250mm) ; 2~12 fiber ribbon

Ribbon Fiber (200mm) ; 2~16 fiber ribbon

Clad Diameter

125 m

Coating Diameter

Single Fiber ; 0.20~3.0 mm

Ribbon Fiber ; 0.20~0.40mm×0.25mm pitch

Ribbon Fiber ; 0.20~0.40mm×0.20mm pitch

Cleave Length

Single Fiber ; 3~16 mm (Used Single Fiber

Adapter)

Tape ; 10 mm (Used Fiber holder)

Cutting Blade Life

65,000 fiber (2,500 fiber per cutting blade position)

※0.2 mm pitch ribbon fiber decrease of cleaves.

Dimension

88W×93D×54H mm (Closed for Carrying)

Weight

320 g

Environmental

Operating Temperature ; -10℃ ~ +50℃

Storage Temperature ; -40℃ ~ +60℃

Humidity(Non Condensing) ; ~ 95%

5.Operating instructions

5.1. Unlock cover of Clamp Arm

The Cover of Clamp Arm should be locked during transportation. Unlock the

Cover prior to use and select appropriate opening angle. Semi-Open or Fully

Open.

①Press the Cover down.

②Turn the knob to appropriate position.

ATTENTION

・Secure the Cover in the closed position during transportation. If the knob is

in the halfway position, the Cover may open.

・Do not push the open FR Arm during use or storage. Components may be

damaged, preventing normal disconnection.

Full Open Should be changed to “Fully Open”, change to Semi-open for In-hand use Close for … must be changed

to “Closed for carrying”

5.2. Cleaving fiber

①Push the Blade Unit to the back until it latches.

②Set a prepared fiber (stripped and cleaned) across cleaving area with

fiber end inserted into the Waste Bin.

Ensure that the stripped fiber is long enough to reach the Pinch Roller.

Put fiber to the appropriate v-groove on the single fiber adapter, depending

on the coating diameter of optical fiber.

In case of ribbon fiber cleaving, please use the ribbon fiber holder

(Optional parts).

When using ribbon fiber, check that the fibers are aligned horizontally and

no fibers are overlapping with each other.

ATTENTION

Fibers should be set at the appropriate length.

If it is too short to reach the Pinch Roller, the fiber shard may not be

collected in the waste bin.

If it is too long, the fiber may bend and not be cut properly.

③ Press the Cover of Clamp Arm until the Blade Unit starts to slide.

Fiber Holder

5.3. Disposing of waste fiber

①Pull down the edge of Waste Bin.

②Slide out the Waste Bin.

ATTENTION

Fibers may pop out when pulling out the Waste bin.

Avoid getting them in your eyes.

Do this action on top of fiber disposal bin, as fiber waste that doesn’t fit into

the bin may spill out.

5.4. Blade rotation

① Slide out the Waste Bin (Refer to 5.4)

② Push in the Blade Unit until it latches then press more firmly until the

Blade Rotation Thumbwheel is unlocked.

③ Rotate the Thumbwheel to increment the blade position by 1.

If you accidentally incremented too much, turn the Thumbwheel

through one full turn.

ATTENTION

Don’t touch the FR arm while working on ②③.

Please take care not to tilt S327 Precision Cleaver too much, as fiber will spill

out of the Waste bin.

Take care not to cut your fingers with the Blade.

6.Blade and Pinch Roller Maintenance

When cleaving quality degrades, clean the top of blade and upper and lower

clamping pads with a cotton swab with a little ethyl alcohol.

After repeated use, abrasion may form on the rubber of the pinch roller. If

fiber waste can’t be collected well enough, the pinch roller needs to be

replaced. Contact our service center for replacement.

The blade can be replaced by the customer.

Purchase and replace the optional parts; “Blade Exchange Set“ (S327X-24).

It does not guarantee End-Face condition or Cutting Blade Life.

If the above does not solve the problem, the function may be temporarily

restored by removing the seal (light blue in the diagram below) and adjusting

the height of the cutting blade using the attached hexagonal wrench.

It does not guarantee End-Face condition or Cutting Blade Life.

After implementation, contact the service center immediately for repair.

~Raise the height of the Blade~

1. Loosen ② screw

2. Turn ① in the “+” direction of the 1 tick.

3. Tighten ② screws

~Lower the height of the Blade~

1. Turn ① in the “–“ direction of the 1 tick.

2. Tighten ② screws

7.Disposal

S327 contains no hazardous substances or recyclable materials. If disposed of,

follow your local disposal regulations.

8.Contacts

For sales and service information,

Contact FURUKAWA ELECTRIC CO., LTD.

Or your local representative.

Sales Department:

Furukawa Electric Co., Ltd.

Tokiwabashi Tower, 6-4,Otemachi 2-Chome, Chiyoda-ku, Tokyo, 100-8322,

Japan

Table des matières

Autres manuels Fitel Équipement industriel

Fitel

Fitel S326 Series Manuel utilisateur

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Grizzly

Grizzly T32428 Manuel utilisateur

Siemens

Siemens 8MF1 Series Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur