Fisher & Paykel OR24SDPWSX Manuel utilisateur

Installation instructions

FreestandiHg _ange

instructions d'installation

Cuiseur ind _pendant

_)R24S[)PWSX model

WARNING

•ALL RANGES CAN TiP

iNJURY TO PERSON COULD RESULT

• iNSTALL ANTI=TIP DEVICE PACKED

WiTH RANGE

SEE iNSTALLATiON iNSTRUCTiONS

IMPORTANT -PLEASE READ AND FOLLOW

¢" Before beginning, please read these instructions completely and care

¢" Do not remove permanently affixed labels, warnings, or plates from

may void the warranty.

¢" Please observe all local and national codes and ordinances.

¢Please ensure that this product is properly grounded.

¢" The electrical plug should always be accessible.

The installer should leave these instructions with the consumer who should retain

for local inspector's use and for future reference.

Electrical installation must be in accordance with the National Electrical Code, ANIS/

NFPA70 - latest edition and/or local codes.

IN CANADA: Electrical installation must be in accordance with the current CSA C22.1

Canadian Electrical Codes Part 1 and/or local codes.

This appliance is designed and manufactured solely for the cooking of domestic (household)

food and in not suitable for any none domestic application and therefore should not be used

in a commercial environmement.

The appliance guarantee will be void if the appliance is used within a none domestic

environnement i.e. a semi commercial, commercial or communal environment.

WARNING!

THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.

Installation must conform with local codes.

Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a

qualified installer or a service agent.

IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.

TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)

Screwdriver Pencil

Adjustable

wrench

Hammer Tape

measure

N°

Drill

This range is supplied with a protective film on steel and aluminium parts:

This film must be removed before installing/using the appliance.

FOR INSTALLER ONLY

THIS RANGE IS FOR RESIDENTIAL USE ONLY

GENERAL INFORMATION

WARNING!!

1. This appliance shall not be used for space heating. This

information is based on safety considerations.

2. All openings in the wall behind the appliance and in the floor

under the appliance shall be sealed.

3. Keep appliance area clear and free from combustible

materials, gasoline, and other flammable vapors.

4. Do not obstruct the flow of ventilation air.

5. Disconnect the electrical supply to the appliance before

servicing.

6. When removing appliance for cleaning and/or service;

A. Disconnect AC power supply.

B. Carefully remove the range by pulling outward.

CAUTION: Range is heavy; use care in handling.

7. Electrical Requirement

Electrical installation should comply with national and local

codes.

8. The misuse of oven door (e.g. stepping, sitting, or leaning

on them) can result in potential hazards and/or injuries.

9. When installing or removing the range for service, a rolling

lift jack should be used. Do not push against any of the

edges of the range in an attempt to slide it into or out of

the installation. Pushing or pulling a range (rather than using

a lift jack) also increases the possibility of bending the leg

spindles or the internal coupling connectors.

WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The range must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA No. 70-latest

edition, in Canada Canadian Electrical Code.

Installation should be made by a licensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

If an external electrical source is utilized, the installation must

be electrically grounded in accordance with local codes or, in

the absence of local codes, with the national Electrical Code,

ANSl/NFPA 70.

This appliance is equipped with a four-prong grounding plug

(NEMA 14-50P) for your protection against shock hazard and

should be plugged directly into a properly grounded socket.

Do not under any circumstances cut or remove the fourth

(ground) prong from the power plug.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing

service on the range. Replacement parts are available from

factory authorized parts distributors. Contact the nearest parts

distributor in your area.

installation

PROXIMITY TO SIDE CABINETS

1. This range may be installed directly adjacent to existing 36" (914 mm) high base

cabinets.

Range dimensions:

•width: 23" 7/8 (606.5 mm)

• depth: 24" 11/64 (614.1 mm)

• height (without backguard): MIN 35"17/32

32 (920 mm)

• backguard (height): 4" 7/16 (113 mm)

(902.5 mm) - MAX 36" 7/

The electric cord with 4-prong ground plug (NEMA 14-50P) has a length of 72"

+1 "1/2 (1830 mm _+38mm).Grounded outlet should be located 7" 9/32 (185 mm)

from the floor and from the rear left to the rear right side of the range.

2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall

appliances, or other side vertical surfaces above 36" (914 mm) high.

There must be a minimum of 3" (76 mm) side clearance from the range to such

combustible surfaces TO THE LEFT above the 36" (914 mm) high countertop; or

there must be a minimum of 3" (76 mm) side clearance from the range to such

combustible surfaces TO THE RIGHT above the 36" (914 mm) high countertop.

IMPORTANT: One side (left or right) above the 36" (914 mm) high countertop

must always be kept clear.

3. The maximum upper cabinet depth recommended is 13" (330 mm). Wall cabinet

above the range must be a minimum of 30" (762 mm) above the countertop for a

width of minimum 24" (609.6 mm): it has to be centred with the range. Side wall

cabinets above the range must be a minimum of 18" (457 mm) above the coun-

tertop.

_o E

c,J o

c3 o4

o4 o4

co X

Fig.1.1

ELECTRIC CONNECTION

Dotted line showing the position

of the range when installed

Area for electric connection

Fig. 1.2 5

\ i_ _i_

PROXIMITY TO SIDE CABINETS

Fig. 1.3

13"maX.(330ram)

ASSEMBLING THE BACKGUARD

It is mandatory to install the backguard

Assemble the backguard as shown in figure 1.5:

•Screw the 2 screws "A" interposing the spacers.

• Screw the central screw "B".

LEVELLING THE RANGE

The range is equipped with 4 LEVELLING FEET (supplied in a separate kit) and may be

levelled by screwing or unscrewing the feet (fig. 1.8).

It is important to observe the directions of figures 1.6, 1.7a, 1.7b.

Supplied with the range

in a separate kit

_. 1.6

+8ram

-X

/...... \

+5/16"

+11/16"

Supplied with the range

in a separate kit

Fig. 1.7a) _17.5mm Fig. 1.7b JFig. 1.8

YOU MUST USE STABILITY

ANTI TIP BRACKET TO

PREVENT UNIT FROM

TIPPING.

ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS

1. The anti-tip bracket has to be attached as shown on figure below (only rear right

side), it has to be fixed on the floor and on the rear wall by no. 4 (four) suitable screws

(not supplied).

2. After fixing the anti-tip bracket, slide range into place. Be sure the rear right foot

slides under the anti-tip bracket attached.

Dotted line showing the position

of the range when installed ......

ANTI-TIP STABILITY

DEVICE FIXING

Antil-tipstability

Rear right device

feet of range

Fig. 1.9

electrical connection

If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician installer determine that the ground path and wire gauge are in accordance

with local codes.

Be sure that the electrical connection and wire size are adequate and in conformance

with:

- ANSl/NFPA 70 latest edition and local codes and ordinances

- CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local

codes and ordinances.

•Do not ground to a gas pipe.

• Check with a qualified electrical installer if you are not sure the range is properly

grounded.

• Do not have a fuse in the neutral or ground circuit.

• When a 4-wire, single phase 120/240-volt, 60Hz, AC-only electrical supply is avail-

able, a 50 amp maximum circuit protection is required, fused on both sides of the

line.

• A time-delay fuse or circuit breaker is recommended.

• This range is equipped with a Certified Power Cord intended to be plugged into

a standard 14-50R wall receptacle. Be sure the wall receptacle is within reach of

range's final location.

• Do not use an extension cord.

Electrical Shock Hazard

Electrically ground range.

Failure to follow these instruc-

tions can result in death, fire or

electrical shock.

In the case of substitution of the power cord always replace it with a suitable UL or CSA

approved one (with the same technical features of the replaced cord).

Tighten the power cord by using only the power cord strain relief bracket supplied with

the appliance. Allow enough slack to easily attach the cord terminals to the terminal

block.

These operations must be carried out only by an authorized technician.

standard NEMA 14-50R wall receptacle

Power supply cord with

NEMA 14-50P plug

WIRING DIAGRAM

OV%N £OQR LATCh4

ETA

coo_NG

I_[- I

_,\o" \o' N

RElYI

ELI_

1700W

240V

AVERTISSEMENT

eTOUS LES TYPES DE CUISINli_RE

PEUVENT BASCULER

eCELA PEUT PROVOQUER DES BLESSURES

eINSTALLEZ LE DISPOSITIF

ANTIBASCULEMENT FOURNI AVEC LA

CUISINli_RE

eCONSULTEZ LES INSTRUCTIONS

D'INSTALLATION

IMPORTANT -VEUILLEZ LIRE ET SUIVRE C US

¢" Avant de commencer, veuillez lire attentivement toutes les instructions.

¢" N'enlevez pas de I'appareil les etiquettes, plaques ou avertissements permanents. Cela

pourrait annuler la garantie.

¢" Veuillez respecter tousles codes et les r_glements Iocaux et nationaux.

¢" Veuillez vous assurer que cet appareil est bien mis a la terre.

¢" La prise de courant devrait 6tre toujours accessible.

¢L'installateur doit confier ces instructions au consommateur qui les conservera

pour I'usage de I'inspecteur local et pour s'y reporter ult_rieurement.

L'installation electrique doit 6tre conforme a la derniere edition du Code national de I'elec-

tricite, ANSl/NFPA70 et/ou aux codes Iocaux.

AU CANADA : L'installation electrique doit 6tre conforme au Code canadien de I'electricit6

CSA C22.1, partie 1, en vigueur et/ou aux codes Iocaux.

Cet appareil a et6 congu et fabrique uniquement pour la cuisson domestique des aliments et

ne convient pas a. I'usage non menager. Cet appareil ne devrait doric pas _tre utilise darts un

environnement commercial.

La garantie de I'appareil sera annulee s'il est utilise darts un environnement non domestique,

c'est-b.-dire un environnement semi-commercial, commercial ou communautaire.

Autres manuels pour OR24SDPWSX

Table des matières

Langues :

Autres manuels Fisher & Paykel Gamme

Fisher & Paykel

Fisher & Paykel OR24SDMBGX2-N Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR30SCG4R1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RGV3-488 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR60SDBGFX2 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR48DDPWGX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR36SDBMX1 Mode d'emploi

Fisher & Paykel

Fisher & Paykel OR36LDBGX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RGV3-485GD Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RDV3-304 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR24SDPWSX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RGV2305LN Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR48DDPWGX1 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RGT-305 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR30SDPWGX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR24SDPWGX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel CG905CLPX2 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel RGV2366LN Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR24SDPWSX Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR120DDWGFX2 Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR36SDBMX Instructions de fonctionnement

Fisher & Paykel

Fisher & Paykel RDV3-485GD Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR30SCG Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR30SDE6 Series Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR36SCG Manuel utilisateur

Manuels Gamme populaires d'autres marques

Samsung

Samsung FCQ321HTUW Manuel utilisateur

Kenmore

Kenmore 790.45712 Manuel utilisateur

Wolf

Wolf CHR CHSSR Manuel utilisateur

Smeg

Smeg Built-in Microwave Oven Mode d’emploi

Zanussi

Zanussi ZCG054G Manuel utilisateur

Whirlpool

Whirlpool 8575985-W Manuel de la liste des pièces

Frigidaire

Frigidaire 316000635 Manuel utilisateur

GE JCSS630 Manuel utilisateur

Samsung

Samsung NX58M9960P series Manuel utilisateur

Hotpoint

Hotpoint RB524R Guide d'installation

Whirlpool

Whirlpool Roper FGP305KW3 Manuel utilisateur

Amana

Amana ART6610 SERIES Manuel utilisateur

Maytag

Maytag MERH770WB Manuel utilisateur

Fulgor Milano

Fulgor Milano SOFIA Manuel utilisateur

Premier

Premier EF-4358GH Manuel utilisateur

Kenmore

Kenmore 790.9010 Series Manuel utilisateur

KitchenAid

KitchenAid KESC300 Manuel utilisateur

Frigidaire

Frigidaire FFEF3012LS Guide de l'utilisateur