First Team WallMonster Series Manuel utilisateur

First Team, Inc.

WallMonster Series

Installation Instructions

Bill of Materials

A (1) Wall Bracket

B (2) Upper Extension Arms

C (1) Lower Extension Arm Assembly

D (1) H-Frame Backboard Mount

E (1) 5/8” x 25 ½” Rod

F (1) Rim Height Indicator

G (1) Adjustment Crank Actuator

H (1) Crank Handle

I (4) Lift Springs

J (1) Rim Height Stickers

K (8) 5/8”x 3” Hex Bolt

L (1) 5/8”x 5” Hex Bolt

M (9) 5/8” Centerlock Nut

N (8) 5/8” Nylon Flatwasher

O (2) .125”x 2-9/16” Zinc Cotter Pin

P (8) 3/8”x 1 ¼” Hex Bolt

Q (8) 3/8” Flatwasher

R (8) 3/8” Lockwasher

S (8) 3/8” Hex

NOTE: Immediately unpack all components and cross check against bill of materials.

Report any shortages to First Team customer service at 1-888-884-6677.

WARNING!! WARNING!! WARNING!! WARNING!! WARNING!!

Proper installation of this basketball structure requires adequate wall

structure integrity. Consult with an architect or engineer if you are

uncertain about whether your roof or wall is sufficient to support this

structure adequately.

WARNING!! WARNING!! WARNING!! WARNING!! WARNING!!

Because each installation situation is unique, the anchoring hardware

required to attach this system to your wall is not included with the

unit. It is up to you to determine what hardware is suitable for your

particular installation. It is advisable to consult with an architect or

engineer if you are unsure about selecting the appropriate mounting

hardware. Inadequate or improper installation of this basketball

system can result in serious injury or death!

Read and understand all instructions completely before proceeding

with installation.

WALLMONSTER WALL MOUNTING

First, refer to FIGURE A and B on page one of the assembly

instructions. NOTE: The WallMonster may be installed either with a

36” or 48” OFFSET (distance from wall to backboard with rim at ten

feet) Position the WALL BRACKET on your wall based on either

FIGURE A or FIGURE B depending on the desired offset. Be sure

WALL BRACKET is positioned correct distance above the playing

surface. (refer to figure c for wall bracket top and bottom orientation)

Secure the WALLBRACKET to wall. HARDWARE FOR SECURING

ASSEMBLY TO WALL IS NOT SUPPLIED AND IS THE

RESPONSIBILITY OF THE CUSTOMER. While securing structure to

wall it is important to place a level on the side of the WALL BRACKET

to insure that the structure is level side to side before finishing

attachment. Adjust as necessary until level.

NOTE: After you are satisfied that the structure is adequately fastened

to the wall and that the wall is adequate to support the weight of this

basketball system, you may proceed with the rest of the installation.

Locate the LOWER EXTENSION ARM assembly. Using Figure A (or

Figure B) note that the LOWER EXTENSION ARM has 3 sets of holes

drilled through it. The end with the holes closest to each other is the

end that mounts to the WALL BRACKET.

With the LOWER EXTENSION ARM oriented properly, attach the

LOWER EXTENSION ARM assembly to the WALL BRACKET using (2)

5/8”x 3” hex bolt, (2) 5/8” nylon flatwashers and (2) 5/8” centerlock

nut. Place one nylon flatwasher on each side between the LOWER

EXTENSION ARM and the WALL BRACKET support. The nylon washers

eliminate paint wear and provide free movement at the pivot points.

Remember, the nylon flatwashers go BETWEEN the extension arms

and the side of the wall bracket.

Attach the UPPER EXTENSION ARMS using (2) 5/8”x 3” hex bolt, (2)

5/8” nylon flatwashers, and (2) 5/8” centerlock nuts. Remember, the

nylon flatwashers go BETWEEN the extension arms and the side of the

wall bracket.

Next, using (1) 5/8”x 5” hex bolt and (1) 5/8” centerlock nut, attach

the ADJUSTMENT CRANK ACTUATOR to the ACTUATOR ATTACHEMENT

EARS on the WALL BRACKET (see figure D). The yoked clevis of the

adjustment crank should be cradled between the two welded tabs

(ACTUATOR ATTACHMENT EARS) at the top of the WALL BRACKET

support. Also attach the RIM HEIGHT INDICATOR at this time. The

welded tube on the RIM HEIGHT INDICATOR fits between the yoked

clevis on the adjustment crank. NOTE OF CLARIFICATION: The

Adjustment Crank Actuator and Rim Height Indicator are both attached

using the same 5/8”x 5” hex bolt mentioned above.

Using (1) 5/8”x 25 1/2” ROD provided and (2) .125”x 2-9/16” COTTER

PIN attach the bottom end of the ADJUSTMENT CRANK ACTUATOR

between the set of welded ears on the LOWER EXTENSION ARM as

shown in Figure A & B. Secure 5/8” ROD in place using COTTER PINS.

Bolt the H-Frame to the extension arms using (4) 5/8”x 3” hex bolts,

(4) 5/8” nylon washers and (4) 5/8” centerlock nuts. Remember to

place the nylon washers between the extension arms and the sides of

the H-Fame.

IF YOU PURCHASED A TEMPERED GLASS OR ACRYLIC

(plexiglass) BACKBOARD you should find (4) grommets mounted in

the four rim holes in the glass. If the grommets are not there, check

the box, they may have fallen out during shipping. If the grommets

are missing and cannot be located, DO NOT PROCEED WITH

INSTALLATION, call First Team immediately for replacements, 1-888-

884-6677. Grommets prevent glass/acrylic breakage when tightening

rim bolts. NO GROMMETS ARE NECESSARY FOR NON-CLEAR

BACKBOARDS.

Hang backboard on H-FRAME lining up the four holes at the top of the

BACKBOARD frame with the four holes in the top of the H-FRAME.

Loosely attach BACKBOARD at these four points using (4) 3/8”x 1 ¼”

hex bolts, flatwashers, lockwashers and hex nuts provided.

Loosely attach BACKBOARD to H-FRAME at the four points along the

bottom of the backboard frame as well. Use (4) 3/8”x 1 ¼” hex bolts,

flatwashers, lockwashers and hex nuts provided. Be sure the rim

holes in the BACKBOARD and the rim holes in the H-FRAME are aligned

so the rim bolts will be able to pass thru when attaching rim.

If you have a tempered glass or acrylic backboard, check once again to

make sure all (4) grommets are in place in the backboard rim

mounting holes. When you are satisfied with rim hole/H-Frame

alignment, attach RIM following the instructions provided in the rim

box. Then tighten the 3/8” hardware at both the top and bottom of

the BACKBOARD frame.

Next, using a measuring tape and CRANK HANDLE crank unit until rim

measures 10’ from playing surface. Make a pencil mark on the side of

the adjustment crank where the height indicator stops. Repeat this

step for 9 ½’, 9’, 8 ½’, 8’, 7 ½’. When finished peel and apply each

rim height sticker lining up the pencil mark with mark provided on

each respective sticker.

Next, using the CRANK HANDLE, crank unit upward so RIM reaches 10’

mark. Then attach (2) lift springs on either side of the CRANK

ADJUSTMENT ACTUATOR attaching one end first on the LIFT SPRING

ATTACHMENT ROD (see figure c) and the other end of the LIFT

SPRING on the 5/8”x 25 ½” ROD mounted on the LOWER EXTENSION

ARM (see figure A & B) You may find it helpful to loop a rope over the

5/8” ROD and attach it to one end of the spring. Then with the spring

already attached to the LIFT SPRING ATTACHMENT ROD, pull down on

the rope, extending the spring until it hooks itself over the 5/8” x 25

½” ROD. The welded ears on either side of the ACTUATOR

ATTACHEMENT TUBE are designed to cradle two LIFT SPRINGS each.

Make sure all hardware has been tightened. If unit is difficult to crank

you may have over tightened the bolts at the main pivot points, try

loosening them slightly. Check over the unit periodically to make sure

no hardware has loosened as the unit ages.

Installation of your First Team WallMonster Basketball System is complete!

TIP: Find a safe and handy location to store your crank handle. If you ever lose

your crank handle, replacements can be purchased by calling First Team at 1-888-

884-6677. We hope you enjoy your WallMonster basketball system.

Table des matières

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur