Fireye MBCE-110FR-1 Manuel utilisateur

DESCRIPTION

The MBCE-110/230FR modules provide visual indication and electrical outputs that

signal the user regarding flame presence in a combustion chamber. The module uses

Fireye flame rods to sense flame presence independently or as components in a burner

management system. Many operational characteristics are provided including:

•CE approved

•Self-contained: 110 VAC, 50/60 Hz: MBCE-110FR-1, MBCE-110FR-3

230 VAC, 50/60 Hz: MBCE-230FR-1, MBCE-230FR-3

•Flame Rod compatible

•Flame ON/OFF LED indicator

•4-20mA permits direct reading of flame signal strength

•Uses CE approved 11-pin relay base

•Panel surface or DIN-rail mounting

•Self-check

The unit provides a cost effective, self-checking method of monitoring flames using

the ionization principle.

Check with Fireye for more details by contacting your local distributor or by check-

ing the Fireye home page at www.fireye.com.

NOTE: When the MBCE-110/230FR modules are used, additional means must be furnished to provide

those functions usually provided by flame safeguard control systems to meet local regulations (i.e.:

safe start checks, valve closure, starting and running interlocks, safety timings, etc.).

WARNING: The Equipment described in this manual is capable of causing property damage, severe

injury, or death. It is the responsibility of the owner or operator to ensure that the equipment

described is installed, operated, and commissioned in compliance with the requirements of all

national and local legislation, which may prevail. Installation, commissioning, or adjustment of this

product MUST be carried out by suitably trained engineer or personnel qualified by training or

experience.

NOTICE: When Fireye products are combined with equipment manufactured by others and/ or

integrated into systems designed or manufactured by others, the Fireye warranty, as stated in its

General Terms and Conditions of Sale, pertains only to the Fireye products and not to any other

equipment or to the combined system or its overall performance.

MBCE-1001

May 11, 2021

MBCE-110/230FR

Flame Sensor

Module

exida

F M E D

S I L 2

SEE NOTE 1 ON PAGE 4

ORDERING INFORMATION

PART NUMBER

DESCRIPTION

BULLETIN

Flame Sensor

MBCE-110FR-1

Single channel module, 110 VAC 50/60 Hz, use with flame rod, 1 sec. FFRT.

MBCE-1001

MBCE-110FR-3

Single channel module, 110 VAC 50/60 Hz, use with flame rod, 3 sec. FFRT.

MBCE-1001

MBCE-230FR-1

Single channel module, 230 VAC 50/60 Hz, use with flame rod, 1 sec. FFRT.

MBCE-1001

MBCE-230FR-3

Single channel module, 230 VAC 50/60 Hz, use with flame rod, 3 sec. FFRT.

MBCE-1001

Flame Sensor (ATEX / IECEx Ex d IIC T6

MBCE-110FR-1CEX

Single channel module, 110 VAC 50/60 Hz, use with flame rod, 1 sec. FFRT.

MBCE-1001

MBCE-110FR-3CEX

Single channel module, 110 VAC 50/60 Hz, use with flame rod, 3 sec. FFRT.

MBCE-1001

MBCE-230FR-1CEX

Single channel module, 230 VAC 50/60 Hz, use with flame rod, 1 sec. FFRT.

MBCE-1001

MBCE-230FR-3CEX

Single channel module, 230 VAC 50/60 Hz, use with flame rod, 3 sec. FFRT.

MBCE-1001

Wiring Base

60-2886

Plug in wiring base, DIN rail or panel surface mount complete with retaining kit.

MBCE-1001

Mounting Rails

60-2539-12

DIN style mounting rail, 12 inches, mounts up to 4 modules.

60-2539-24

DIN style mounting rail, 24 inches, mounts up to 8 modules.

60-2539-36

DIN style mounting rail, 36 inches, mounts up to 12 modules.

Flame Rods

69ND1-1000K4

Flame rod 1/2” NPT mount, 12” length.

SC-103

69ND1-1000K6

Flame rod 1/2” NPT mount, 18” length.

SC-103

69ND1-1000K8

Flame rod 1/2” NPT mount, 21” length.

SC-103

PRODUCT SPECIFICATIONS

Supply Voltage: MBCE-110FR - 110 VAC (+10%, -15%), 50/60

Hz (@ 0.1 Amp consumption)

MBCE-230FR - 230 VAC (+10%, -15%), 50/60

Hz (@ 0.05 Amp consumption)

Flame Relay Output: SPDT 2 Amp Resistive @ 110VAC, 1 Amp @

30VDC

SPDT 1 Amp Resistive @ 230VAC, 1 Amp @

30VDC

Flame Fail Response Time: 1 or 3 seconds - depending on part number (-1, -3)

Operating Temperature: - 40° F to 150° F (- 40° C to 65° C)

Storage Temperature: - 40° F to 176° F (- 40° C to 80° C)

Humidity: 85% RH (max), non-condensing.

Agency Approvals: (Note1)

MBCE-110FR CE / EN298

MBCE-230FR CE / EN298

Shipping Weight: 1 lb (.5 Kg)

Flame Rod: S1 = Terminal 4

S2 = Terminal 8 (local panel ground)

Power: Terminals 4 and 8, - 240 - 360 VAC

Note: Measured with digital VOM

Terminals 5 and 8 are internally connected.

Sensitivity: Flame Rod - 3 μA @ 100 Meg ohms

IP-Rating IP-20

Test Jacks: Standby/No flame 4mA

Flame signal (Min) 6mA

Flame signal (Max) 20mA

PRODUCT SPECIFICATIONS (CEX Models)

Supply Voltage: MBCE-110FR-CEX - 110 VAC (+10%, -15%), 50/60

Hz (@ 0.1 Amp consumption)

MBCE-230FR-CEX - 230 VAC (+10%, -15%), 50/60

Hz (@ 0.05 Amp consumption)

Flame Relay Output: SPDT 2 Amp Resistive @ 110VAC, 1 Amp @ 30VDC

SPDT 1 Amp Resistive @ 230VAC, 1 Amp @ 30VDC

Flame Fail Response Time: 1 or 3 seconds - depending on part number (-1, -3)

Operating Temperature: - 400F to 1310F (- 400C to 550C)

Storage Temperature: - 400F to 1760F (- 400C to 800C)

Humidity: 85% RH (max), non-condensing.

Agency Approvals: (Note1)

MBCE-110FR & MBCE-230FR (CEX): CE / EN 298

ATEX: EN 60079-0, EN 60079-1, EN 60079-31, and EN 60529

IECEx: IEC 60079-0, IEC 60079-1, IEC 60079-31

Shipping Weight: 6 lb (2.72 Kg)

Flame Rod: S1 = Terminal 4

S2 = Terminal 8 (local panel ground)

Power: Terminals 4 and 8, - 240 - 360 VAC

Note: Measured with digital VOM

Terminals 5 and 8 are internally connected.

Sensitivity: Flame Rod - 3 μA @ 100 Meg ohms

IP-Rating IP-20 IP68 (1 Meter Continuous Immersion)

Test Jacks: Standby/No flame 4mA

Flame signal (Min) 6mA

Flame signal (Max) 20mA

FIGURE 1. MBCE (CEX) HAZARDOUS AREA HOUSING

ATEX Certificate # FM13ATEX0038X

IECEx Certificate # IECEx FMG 13.0018X

Specific Conditions of Use (ATEX / IECEx):

1. Consult the manufacturer if dimensional information on the flameproof joints is necessary.

2. As the Explosion-Protected Flame Sensor is only one element of a flame sensing system for a

combustion safeguard, it has not been evaluated by FM Approvals against the combustion

safeguard performance requirements. Additional certification and performance testing may be

required by jurisdictional authorities.

3. Shall be installed as per the requirements in EN 60079-14 or IEC 60079-14, as applicable.

4. Shall use cable glands or conduit entry devices rated for the application to maintain the

explosion protection and IP rating.

5. The MBCE flame sensors are not repairable. If repairs are required, consult the manufacturer.

Note: The MBCE-110FR & MBCE-110FR have been evaluated to EN 298:2012 by TUV, and

meet the Gas Appliance Directive (2009/142/EC)

CE Certificate # CE-0085BT0365

DIN DVGW Certificate # NG-4131BT0364

DIN CERTCO Registration # 5F234

Note 1: Based on Exida’s FMEDA report no. FIR 09/10-26 R001 dated December 13, 2010,

Fireye certifies that the MBCE Flame Sensor Modules are suitable for installations up to and

including SIL2

Example of product label

FIGURE 2. DIMENSIONS OF DIN RAILS, WIRING BASES AND FLAME SWITCH MODULES SHOWN IN INCHES (MM)

STYLE: 11 pin octal, snap-mount/surface mount

TYPE OF CONECTION: Screw connection

STRIPPING LENGTH: 10mm

SCREW THREAD: M3

WIRE SIZE: Maximum up to 2 - #14AWG each terminal

ELECTRICAL RATING: 400V, 10A

To secure MBCE-110/230FR to socket use retaining kit P/N 60-2886

1.49 37.82

.13 3.18 DIA. TYP.

1.03 26.09

2.96 75.06

.14 3.56

1.46 37.08

0539

SENSOR INSTALLATION

WARNING: Incorrect flame rod installation may result in the generation of a false flame

signal, causing unburned fuel to collect in the combustion chamber. The result can be

explosions, injuries and property damage. Be certain that the flame rod detects only pilot

and/or main flames.

Route sensor wiring a sufficient distance from ignition and other high voltage or high current wiring to

avoid electrical interference. Interference from ground currents, nearby conductors, radio-frequency

emitters (wireless devices), and inverter drives can induce false flame signals. Shielded cables can help

reduce interference with the shield connected to ground at the control end only. The wire type and its

capacitance (picofarads or microfarads) to ground may cause low signal problems, so a grounded shield

may decrease the signal due to the cable's internal capacitance. Multiple sensor leads run together

without shielding may interfere or “cross talk”, so the shield or flexible armor must be grounded to

prevent this situation. For flame rod sensor runs approximately 100 feet (30 meters) or greater, use

Belden P/N 8254-RG62 coax cable. To achieve the maximum wiring distance, the shield should not be

grounded (keep in mind that an underground shield provides less protection against electrical

interference). Depending on field connections, sensor wiring can be up to 200 feet (61 meters).

Do not ground the shield to terminal GND.

Unshielded sensor wiring must not be run in common with other wires; it must be run in separate conduit.

Multiple flame sensor wiring must not be run together in a common conduit or wireway. Use #14 to #18

AWG wire suitable for 90°C (194°F) and 600-volt insulation and run each pair of leads in its own shielded

cable. Multiple shielded cables can be run in a common conduit.

Flame rods are recommended to be used on gas burners. They accumulate soot on oil burners, causing

nuisance shutdowns and unsafe operating conditions.

See the burner manufacturer's literature for flame rod mounting location.

INDICATION LEDS

The CE Flameswitch contains two bi-color LEDs that are used to provide flame status and alarm

condition per the following table.

LEDs can be viewed through the cutout located on the top side of the unit.

LED

COLOR

DEVICE STATUS

LED 1

(SYSTEM LED)

GREEN

SYSTEM OK

BLINKING GREEN

SELF-CHECKING

BLINKING RED/ORANGE

ALARM

SOLID RED/ORANGE

SYSTEM FAULT

LED 2

(FLAME LED)

SOLID GREEN

GOOD FLAME

BLINKING GREEN

WEAK FLAME

BLINKING RED/ORANGE

FLAME RELAY FAULT

SOLID RED/ORANGE

OTHER FLAME FAULTS

OFF

FLAME OFF

WIRING BASE PINOUT INFORMATION

The following table shows the wiring information and the ratings. To guarantee proper

operation, the unit MUST NOT be operated above its maximum rating.

TERMINAL NO.

TERMINAL NAME

DESCRIPTION

DIRECTION

RATING

(11)

OPEN

UNUSED

N/A

(A1)

4-20mA COM

4-20mA COMMON

LOCAL

GROUND

(14)

4-20mA OUT

4-20mA OUTPUT

OUTPUT

28 VDC, 20mA max

(12)

FLAME ROD EXCITATION

OUTPUT

300 VAC, 1mA max

(22)

PROTECTIVE

EARTH

GROUND

(21)

NEUTRAL

INPUT

(24)

LINE VOLTAGE SUPPLY

INPUT

110/230 VAC (+10%,-

15%) 50/60 Hz

(32)

FLAME ROD RETURN

EARTH

GROUND

(34)

FLAME RELAY

NORMALLY OPEN (N.0.)

OUTPUT

110 VAC, 2A max/

230 VAC, 1A max

30 VDC, 1A max

(A2)

COM

FLAME RELAY

COMMON

INPUT

110 VAC, 2A max/

230 VAC, 1A max

30 VDC, 1A max

(31)

FLAME RELAY

NORMALLY CLOSED (N.C.)

OUTPUT

110 VAC, 2A max/

230 VAC, 1A max

30 VDC, 1A max

Any equipment connected to the 4-20 mA current loops shall be insulated from hazardous live

parts by protective separation (e.g., double, or reinforced insulation according to DIN EN

61010, DIN EN 50178, DIN EN 60730-1 or DIN EN 60950).

FLAME SIGNAL STRENGTH vs. 4-20mA OUTPUT

4-20mA measurements can be taken from the test jack connector located at the faceplate of the

unit. Measurements can also be taken using the dedicated 4-20mA OUT & 4-20mA COM

terminals located at the wiring base.

NOTE: The 4-20mA return path is labeled “GND” on the faceplate. This is simply a local return

path for the 4-20mA current, and it MUST NOT be attached or referenced to earth ground or other

forms of ground connection. Likewise, 4-20mA COM is the return path at the wiring base and

MUST NOT be attached or referenced to earth ground or other forms of ground connection.

SPECIAL CONDITIONS OF USE

1. The equipment shall be installed in compliance with the enclosure, mounting spacing and segregation requirements

of the ultimate application.

2. Line voltage and extra-low voltage wiring to and from this device is intended to be wired in the field to become

part of a Class 1 circuit only.

FIGURE 3. TYPICAL APPLICATION -- MBCE-110/230FR

NOTE: BURNER GROUND

AND PANEL GROUND MUST

BE THE SAME POTENTIAL

NOTICE

When Fireye products are combined with equipment manufactured by others and/or integrated into systems designed

or manufactured by others, the Fireye warranty, as stated in its General Terms & Conditions of Sale, pertains only to

the Fireye products and not to any other equipment or to the combined system or its overall performance.

WARRANTIES, EXCLUSIVE REMEDIES, AND LIMITATION OF DAMAGES

Fireye guarantees for one year from the date of installation or 18 months from the date of manufacture,

whichever occurs first, to replace, or at its option, to repair any product or part thereof which Fireye, in its

sole discretion, deems to be defective in material or workmanship or which otherwise fails to conform to

the description of the product on the face of its sales order. Fireye’s obligations pursuant to this warranty

do not extend to any products or parts thereof which Fireye determines to have been installed, operated,

maintained, repaired, or altered improperly or otherwise than in conformity to Fireye’s applicable

instructions, or which have been subject to misuse, accident, or neglect.

THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, BOTH EXPRESS AND IMPLIED,

INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. EXCEPT AS SPECIFICALLY STATED IN THESE TERMS AND CONDITIONS OF SALE,

REMEDIES WITH RESPECT TO ANY PRODUCT OR PART MANUFACTURED OR SOLD BY FIREYE,

OR WITH RESPECT TO ANY BREACH OF OR DEFAULT UNDER THIS CONTRACT (INCLUDING ANY

BREACH OF WARRANTY), SHALL BE LIMITED EXCLUSIVELY TO THE RIGHT TO REPLACEMENT

OR REPAIR F.O.B. FIREYE MAIN WAREHOUSE LOCATION, AS ABOVE PROVIDED. IN NO EVENT

SHALL FIREYE BE LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE

WHICH MAY ARISE IN CONNECTION WITH SUCH PRODUCT OR PART OR ANY BREACH OF OR

DEFAULT UNDER THIS CONTRACT. TO THE EXTENT PERMITTED BY LAW, THE AGGREGATE

LIABILITY OF FIREYE HEREUNDER WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE)

OR OTHERWISE, WILL BE LIMITED TO ONE TIMES THE CONTRACT VALUE, PROVIDED

HOWEVER THE FOREGOING LIMITATION DOES NOT LIMIT THE LIABILITY OF FIREYE FOR ANY

INJURY TO, OR DEATH OF A PERSON, CAUSED BY THE GROSS NEGLEGENCE OF FIREYE

FIREYE, Inc. MBCE-1001

3 Manchester Road May 19, 2023

Derry, New Hampshire 03038 USA Supersedes June 4, 2020

Fireye.com

Ce manuel convient aux modèles suivants

Autres manuels Fireye Accessoires

Fireye

Fireye BLPS-25 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur