Firex KF30 Manuel utilisateur

• Adjacent to, or directly above, heaters, air-conditioning vents or ceiling fans.

• In an area where the temperature may fall below -30°C or rise above 37°C.

• In areas above 93% relative humidity (RH), non-condensing.

• Near fluorescent lights. Electrical noise and flickering may affect the

operation of the heat alarm.

• Closer than 300mm to light fittings.

• In such a position that it is difficult or dangerous to reach for testing or main-

tenance.

• Do not site the alarm in an area where water or other liquids may enter the alarm.

HOW TO INSTALL THIS HEAT ALARM

DANGER: ELECTRIC SHOCK HAZARD.TURN OFF POWER TO THE HEAT A ARM CIRCUIT AT THE MAIN DIS-

TRIBUTION BOARD BY REMOVING THE FUSE OR SWITCHING THE CIRCUIT BREAKER TO THE OFF POSITION

AND SECURING IT.

ARNING: THIS HEAT A ARM SHOU D BE INSTA ED ON Y BY A QUA IFIED E ECTRICIAN IN ACCOR-

DANCE WITH THE REGU ATIONS FOR EECTRICA INSTA ATIONS PUB ISHED BY THE INSTITUTION OF EEC-

TRICA ENGINEERS (BS 7671) AND/OR A PRESIDING OCA ,REGIONA AND NATIONA CODES.

WARNING: HEAT A ARMS SHOU D BE CONNECTED ON A SING E INDEPENDENT,

DEDICATED CIRCUIT AT THE MAIN DISTRIBUTION BOARD. NO OTHER E ECTRICA

EQUIPMENT, EXCEPT COMPATIB E SMOKE AND CO A ARMS, SHOU D BE CON-

NECTED TO THIS CIRCUIT. IF YOUR HOME HAS RESIDUA CURRENT DEVICE PRO-

TECTION ON THE E ECTRICA INSTA ATION OR ON INDIVIDUA CIRCUITS, CHECK

WITH A QUA IFIED E ECTRICIAN TO MAKE SURE THAT FAU TS ON CIRCUITS SERV-

ING SOCKET OUT ETS OR PORTAB E APP IANCES CANNOT CAUSE INTERRUPTION

TO THE SUPP Y TO THE HEAT A ARMS.

1. Route the household AC supply/interconnect cable into the dry lining box or

Firex surface pattress.

2. Using a suitably-rated terminal block, connect the neutral supply to the blue

lead of the connector plug.

3. Using a suitably-rated terminal block, (supplied with Firex pattresses),connect

the line supply to the brown lead of the connector plug.

4. If interconnecting is desired, connect the orange or white of the connector

plug to the designated interconnect conductor of the household cable. See

note INTERCONNECTING HEAT ALARMS.

NOTE: If this is to be a single-station heat alarm, connect the orange or white

wire to an unused terminal block

5. Insert the completed connector block onto the mounting pins of the Firex Pat-

tress or recess into dry lining box.

6. For the F30, F30LL ONLY :

a. Open the battery compartment door.

b. Connect a new, healthy 9V DC battery to the battery connector inside the

battery compartment. Be sure the battery is securely connected.

The heatalarm may beep briefly when the battery is installed.

c. Close the battery compartment door, snapping it into place.

d. For F30LL, the battery door can be locked using the tamper-proof screw

provided.

7. Pass the connector plug through the mounting plate of the heat alarm, align

slots and fasten mounting plate securely to the Firex Pattress or dry lining box.

NOTE: If this is to be a single-station heat alarm, connect the orange or white wire

to an unused terminal block

8. Attach the connector plug to the pins on the back of the heat alarm. The plug

will only fit one way, and will snap into place.

9. Gently tug the connector to be sure it is attached securely.

10. Position the heat alarm on the mounting plate and turn it clockwise to lock it

into place.

11. Turn on the power to the heat alarm circuit at the main distribution board.

12. Test the heat alarm for AC operation. See TESTING THE HEAT ALARM.

• Some fires are slow smouldering, low heat-producing, or are in a different

room to that in which the heat alarm is located, or the heat from the fire may

bypass the alarm – the heat alarm may not give a warning under these cir-

cumstances.

• HEAT ALARMS HAVE LIMITATIONS. This heat alarm is not guaranteed to protect

lives or property. Heat alarms are not a substitute for insurance. Householders

should insure their lives and property. In addition, as with any electronic device,

it is possible for the heat alarm to fail at any time.

• Never paint this heat alarm.

HEAT ALARM LOCATION

Heat alarms give an audible warning when the temperature at the alarm reaches

57°C. Heat alarms are ideal for kitchens, garages, cellars, boiler rooms, attics and

other areas where there are normally high levels of fumes, smoke or dust which pre-

clude the use of smoke alarms due to the risk of false alarms.

Guidance on fire detection in dwellings is contained in BS 5839: Part 6. For normal-

sized bungalows, two-story houses, flats and maisonettes, the British Standard rec-

ommends that the minimum level of protection should comprise smoke alarms in the

hallways and staircases. This minimum standard necessitates one smoke alarm in the

hallway of a typical bungalow or one smoke alarm on each level of a two-story house.

Heat alarms should not be used in these circulation areas. If there are, for example,

long hallways, even the minimum standard may necessitate additional interconnected

smoke alarms.

If, however, the design of the dwelling does not comply with modern fire safety stan-

dards, or if factors such as the presence of several young children, or elderly occu-

pants or disabled people, or of smokers, the use of portable heaters or solid fuel fires

during the night, or the use of electric blankets, particularly by the elderly, the British

Standard advises that additional detection devices, installed within rooms, may be

necessary.

The British Standard recommends that, if the risk justifies the provision of detectors in

a kitchen, boiler room, or other area (except a circulation area) in which smoke

alarms would be likely to give false alarms, heat alarms should be used. However, the

Standard also advises that heat alarms may be installed in other rooms instead of

smoke alarms, provided that the construction enclosing the room (including the door)

can resist fire for a sufficient time after operation of a heat alarm to enable occupants

to escape safely. However, a heat alarm is unlikely to operate early enough to save

the life of anyone asleep in the room in which it is installed. Moreover, a heat alarm in

the room of fire origin may not give sufficient warning for occupants to escape safely

if the door to that room is open. A Heat Alarm is also recommended in the Living

Room, if a smoke alarm in that location, suffers nuisance alarms from smokers.

HEAT ALARM SITING

FOR BEST PROTECTION, IT IS RECOMMENDED THAT YOU INSTALL A SMOKE OR

HEAT ALARM IN EVERY ROOM. In addition, it is recommended that all smoke and

heat alarms should be interconnected.

Install heat alarm on a standard dry lining box or Firex pattress as close to the centre of

the ceiling as possible. If the centre is not practical, mount the heat alarm no closer

than 300mm away from a wall or corner.

In rooms with open joists or beams, all ceiling-mounted alarms should be located

on the bottom of such joists or beams and not up in joist channels. On sloped,

peaked or gabled ceilings, install heat alarm 90cm from highest point. If only wall

placement is possible, install no further than 150mm from ceiling.

DO NOT install heat alarms:

• Directly over the cooker, stove or oven.

• In areas with high humidity, like bathrooms or shower rooms, or areas near

dishwashers or washing machines. Install heat alarms at least 3m away from

these areas if possible.

SPECIFICATIONS

ITEM (MODE NUMBER) KF30, KF30 , KF30R

EECTRICA RATING 230V AC, DC BACK UP (KF30: 9V REP ACEAB E,

KF30 ONG IFE 9V ITHIUM,KF30R: RECHARGAB E)

INTERCONNECTING FIREX UP TO ANY COMBINATION OF 23OTHER ALARM

SMOKE AND HEAT AARMS MODELS,KF1, KF1R, KF2, KF2R, KF3, KF3R,

(OR PATTRESS WITH RE AY) 4870, 4881, 4973, 4985, 4892, 4899,1SFW, 1SFWR,

2SFW, 2SFWR, 3SFW, 3SFWR AND KS1280

KF10, KF10 , KF10R, KF20, KF20 , KF20R, KF30,

KF30 AND KF30R

TEMPERATURE RATING 57°C

MAXIMUM AMBIENT 37.8°C

TEMPERATURE RATING

OPERATING TEMPERATURE 0°C TO 40°C

OPERATES UP TO 93% HUMIDITY (NON-CONDENSING)

RECOMMENDED COVERAGE 50M2

RECOMMENDED SPACING 5.3M

MAXIMUM DISTANCE FROM WA 7.7M

MAXIMUM CEI ING HEIGHT 6M

IMPORTANT SAFETY INFORMATION

PLEASE READ AND SAVE THESE INSTRUCTIONS

WARNING

• The F30R requires constant 230V AC power AND fully charged batteries to

operate properly. It requires 2 full days under mains power to reachfull back

up capacity. The batteries are not replaceable. Do not connect heat alarm to

any other type of device except those listed in this user guide.

• The F30 and F30LL heat alarm requires constant 230V AC power AND a

healthy 9V DC battery to operate properly. Removal of battery and loss or dis-

connection of AC power will render the alarm inoperative. DO NOT use any

other kind of battery except as specified in this user guide. Do not connect

heat alarm to any other type of device except those listed in this user guide.

• The TEST/FALSE ALARM CONTROL button accurately tests all heat alarmfunc-

tions. DO NOT use any other test method for routine testing. Test heat alarm

weekly to ensure proper operation.

• Higher ceilings will increase the time needed by the heat alarm to detect a

fire. In most dwellings the ceiling height will keep this reaction time within

acceptable limits. However, ceilings with a height of over 6m may delay the

reaction time of the heat alarm significantly. Advice from your local distribu-

tor or Fire Brigade should be obtained when installing a heat alarm on a ceil-

ing higher than 6m.

• This heat alarm should be installed only by a qualified electrician. The installa-

tion should comply with BS 7671 and all prevailing local, regional and national

codes.

• This heat alarm is designed to be used only as part of the protection of a sin-

gle family dwelling or a house in multiple occupation (HMO) of no more than

two stories. It also may be used in conjunction with smoke alarms within indi-

vidual flats or apartments in larger houses in multiple occupation, to provide

an early warning to occupants of a fire in a room within the dwelling, but a

communal fire alarm system also should be provided in such cases. DO NOT

install this heat alarm in any other buildings, such as hotels, motels, dormito-

ries, hospitals, nursing homes or group homes of any kind. In these occupan-

cies, a complete automatic fire detection and alarm system, complying with

BS 5839: Part 1, should be installed.

• Heat alarms should be used only in conjunction with smoke alarms, with

which the heat alarms should be interconnected, in order to provide early

warning of heat, smoke, or fire. Smoke alarms should be installed on every

level of the dwelling.

• Interconnected heat alarms and smoke alarms offer maximum protection. By

interconnecting heat alarms and smoke alarms, when one unit senses heat,

smoke, or fire, and sounds its alarm, all others will sound as well. DO NOT

connect this heat alarm to any other type of alarm except those stated in this

user guide or an approved auxiliary device.

• Heat alarms interconnected with smoke alarms may not alert every household

member every time. The alarm sounder of the heat alarm is loud in order to

alert individuals of a potential danger. However, there may be limiting circum-

stances where an occupant may not hear the alarm (e.g., outdoor or indoor

noise, sound sleepers, drug or alcohol usage, impaired hearing, etc.). House-

hold members must hear the alarm’s warning sound and quickly respond to it

to reduce the risk of damage, injury, or death that may result from fire.

• Check carefully that, when any one device operates, the alarm signal given by

interconnected devices is clearly audible throughout the building, particularly

in bedrooms, where it is essential that the alarm signal will wake sleeping oc-

cupants.

• This heat alarm can sound an alarm only when it detects temperatures of 57°C

or above. Heat alarms do not sense smoke or gas. In some fires, hazardous

levels of toxic chemicals and smoke can build up before a heat alarm will op-

erate. Temperatures may not reach 57°C to activate the heat alarm QUIC LY

ENOUGH to ensure safe escape.

HEAT ALARM FEATURES

• This heat alarm is powered from a 230V AC supply, and has a DC battery back-up

source. AC/DC heat alarms offer added protection in the event of a power failure.

• Unique power connector prevents interconnecting with incompatible heat alarms,

CO alarms, smoke alarms, or security systems.

• Items F30, F30LL and F30R heat alarms can be interconnected with up to 23

other models, F1, F1R, F2, F2R, F3, F3R, 4870, 4881, 4973, 4985, 4892, 4899,

F10, F10R, F20, F20R, F30 and F30R, 1SFW, 1SFWR, 2SFW, 2SFWR, 3SFW

and 3SFWR, 4MCO, 4MDCO. Do not connect to any other type or model of smoke,

CO, or heat alarm.

• Hush quiets unwanted alarms for up to 9 minutes.

• F30R includes permanent rechargeable lithium batteries.

• Alarm memory identifies which alarm has activated

• Optional use tamper-resistant feature serves as a safeguard against tampering.

• The heat alarm will sound a short beep about once every 40 seconds if the battery

is low.

• Multi-purpose green and red LEDs indicate that the heat alarm is connected to the

AC supply, is working normally, or is in alarm.

• Loud alarm sounder – 85 decibels [dB(A)] at 3m – will sound to alert you to an

emergency.

• Test button checks heat alarm operation.

• F30LL is provided with a long life lithium battery that lasts the full life of the alarm

and a tamper-proof option using screw provided

57°C TEMPERATURE RATING

KF30 LOOSE BATTERY

KF30LL SEALED-IN LITHIUM BATTERY

KF30R RECHARGEABLE

PLEASE READ AND SAVE THIS USER GUIDE

Installer: Please leave this user guide with

the occupier (or, in the case of a house

in multiple operation, with the owner).

CONTENTS

p.1 Heat Alarm Features

p.1 Specifications

p.2 Important Safety Information

p.3 Heat Alarm Location

p.3 Heat Alarm Siting

p.4 How to Install This Heat Alarm

p.5 Interconnecting Heat Alarms

p.5 Red and Green LED Indicators

p.5 False Alarm Control

p.5 Testing the Heat Alarm

p.6 Maintenance, Cleaning,and Battery replacement- F30 only

p.7 Repair

p.7 Fire Safety Rules and Preventing Hazardous Situations

p.7 Fire Procedure

p.7 What to Do in Case of Fire

p.8 Troubleshooting

p.8 Guarantee

BEDROOM

ATTIC OFFICE

BEDROOM

HEAT ALARM

OPTICAL ALARM

IONISATION ALARM

KITCHENLIVING ROOM GARAGE

UTILITY/

LAUNDRY

CEILING

INTERLINK

NEUTRAL

BROWN

ORANGE OR WHITE

BLUE

CEILING

INTERLINK

NEUTRAL

BROWN

ORANGE OR WHITE

BLUE

KF30R KF30, KF30LL

Standard Dry Lining box or Firex pattress Standard Dry Lining box or Firex pattress

KF30

KF30LL

KF30R

USER GUIDE

BS5446 pt 2: 2003

LICENSE NO. M503753

WARNING: HEAT A ARMS A ONE ARE NOT SUFFICIENT FOR IFE SAFETY AS THEY ARE NOT DESIGNED TO DE-

TECT SMOKE. THEY ARE INTENDED TO DETECT TEMPERATURES OF 57°C AND ABOVE TO PROVIDE AN ADDI-

TIONA SOURCE OF INFORMATION THAT IS SUPP EMENTARY TO THAT PROVIDED BY SMOKE A ARMS TO

INCREASE THE PROBABI ITY THAT AN EAR Y WARNING WI BE PROVIDED AND SO ENHANCE IFE SAFETY AND

PROPERTY PROTECTION.SEE HEAT ALARMS HAVE LIMITATIONS IN THE IMPORTANT SAFETY

INFORMATION SECTION OF THIS USER GUIDE.

1003-7203-00_(KF30_KF30LL_KF30R)_V6a:_ 2015.2.4 10:07 AM Page 1

These guidelines will assist you in the event of a fire. However, to reduce the chance

that fires will start, practice fire safety rules and prevent hazardous situations. Con-

tact your local Fire Brigade for more information.

TROUBLESHOOTING

GUARANTEE

The manufacturer guarantees this product to be free from defects in material and

workmanship under normal use and service (“Defects”) for a period of six (6) years

from the date of purchase (the “Guarantee Period”). Should any Defects be discov-

ered within the Guarantee Period, the Company will, at its option, repair or replace the

defective product provided that: (a) it is returned during the Guarantee Period with

postage prepaid and with proof of purchase date to the address shown below and (b)

the Company verifies that the claim is proper. This Guarantee does not cover damage

resulting from accident, improper installation, maintenance or repair, misuse, abuse

or product modification. This Guarantee does not confer any rights other than those

expressly set out above and does not cover any claims for consequential loss or dam-

age. This Guarantee is offered as an extra benefit and does not affect your statutory

rights as a consumer.

Return units in a padded carton, postage prepaid, to:

FIREX PRODUCTS

KIDDE SAFETY EUROPE LIMITED

Mathis n Way

Colnbrook, B rkshir SL3 0HB

Unit d Kingdom

T l.: +44 (0) 1753 685148

www.smok -alarms.co.uk

FIRE SAFETY RULES AND PREVENTING

HAZARDOUS SITUATIONS

Siting, testing, and taking care of heat and smoke alarms is just one step in helping to

protect your family and home from fires. You must also reduce the chance that fires will

start in your home and increase your chances of escaping if a fire does start. At a

minimum, your home fire safety program should include the following guidelines:

• Use smoking materials properly – never smoke in bed or when sleepy or under

the influence of alcohol or other drugs.

• eep matches and other sources of ignition away from children.

• Store flammable materials in proper containers and never store or use them

near open flames or sparks.

• eep electrical appliances and their leads in good working condition, and do not

overload electrical circuits.

• eep fireplaces, chimneys, and barbecue grills clean, and make sure they are

properly sited away from combustible materials.

• eep portable heaters and open flames such as candles away from combustible

materials.

• Do not allow rubbish to accumulate.

• Have the electrical wiring in your house checked by a qualified electrician at

least every 10 years (or more often as it ages).

• Never leave cooking unattended.

FIRE PROCEDURE

If you hear the heat or smoke alarm sounding, and you have not pushed the test but-

ton, it is warning you of a dangerous situation. You will need to respond immediately.

To prepare for such occurrences, develop family escape plans, discuss them with all

household members, and practice them regularly. For your safety, as a minimum, you

should do the following to have more effective fire safety.

• Draw a floor plan of your home and find all ways to escape if there is a fire. On

the ground floor, consider whether windows can be used for escape. On upper

floors, consider whether external rescue will be possible if escape routes are

blocked by fire or smoke.

• Expose everyone to the sounds of the heat alarm and of the smoke alarm and ex-

plain what the sounds mean. Show them how to check to see if doors are hot be-

fore opening them, how to stay close to the floor and crawl along the floor to stay

below dangerous smoke, fumes and gases, and how to use the alternative exit if

a door is hot. Instruct them not to open the door if the door is hot.

• Decide on a meeting place a safe distance from your house and make sure all

members of your household understand they should go and wait for you there if

there is a fire. Explain to children that they must be ready to leave the house by

themselves if necessary.

• Hold fire drills every six (6) months to make sure everyone, even small children,

know what to do to escape safely.

• now where to go to call the Fire Brigade from outside your house.

• Provide emergency equipment, such as fire extinguishers, and teach your family

how and when to use this equipment.

WHAT TO DO IN CASE OF A FIRE

After you have prepared family escape plans and practiced them with your family, you

have increased their chances of escaping safely. Review the following rules with your

family when you have fire drills, so everyone will remember them in a real fire.

1. Don’t panic, stay calm. Your safe escape may depend on thinking clearly and

remembering what you have practiced.

2. Get out of the house, following your planned escape route, as quickly as

possible. Do not stop to collect anything or to get dressed.

3. Open doors carefully only after feeling to see if they are hot. Do not open a door

if it is hot; use an alternative escape route. If your escape route is blocked, go to

a window and shout for help. If necessary, stuff clothing or other materials in the

gaps round the room door to stop smoke from entering until help arrives.

4. Stay close to the floor; smoke and hot gases rise toward the ceiling.

5. eep doors and windows closed unless you open them to escape.

6. Meet at your pre-arranged meeting place after leaving the house.

7. Call the Fire Brigade as soon as possible from outside your house. Give your

full address, including the name of the town or village.

8. Always call the Fire Brigade as soon as possible, even if a fire seems small.

9. Never re-enter a burnin or smoke-filled buildin .

2. Firmly depress and hold the TEST/Hush button for at least five (5) seconds. The

heat alarm will sound a loud beep for about three (3) times a second. The

alarm may sound for up to ten (10) seconds after the TEST/Hush button is re-

leased. NOTE: If heat alarms are interconnected, all heat and smoke alarms

should sound an alarm within three (3) seconds after any test button is pushed

and the tested heat alarm sounds.

3. If the heat alarm does not sound, turn off the power to the heat alarm circuit at

the main distribution board and check the wiring. Retest the heat alarm.

!WARNING: IFTHE HEAT A ARM SOUNDS,AND THE HEAT A ARM IS NOT BEING TESTED,THE HEAT

A ARM IS SENSING A TEMPERATURE OF 57°C OR ABOVE.THE A ARM SOUND REQUIRES YOUR

IMMEDIATE ATTENTION AND ACTION. EVACUATE THE DWE ING IMMEDIATE Y!

MAINTENANCE AND CLEANING

In addition to weekly testing, this heat alarm must be cleaned periodically to remove

dust, dirt and debris.

DANGER: ELECTRIC SHOCK HAZARD.

TURN OFF THE AC SUPP Y TO THE HEAT A ARM AT THE MAIN DISTRIBUTION BOARD BY REMOV-

ING THE FUSE OR SWITCHING THE APPROPRIATE CIRCUIT BREAKER TO THE OFF POSITION BE-

FORE C EANING THE HEAT A ARM.

ARNING: HEAT A ARMS ARE IFE-SAVING DEVICES AND SHOU D BE CARED FOR PERIODICA Y

CLEANING

Clean the heat alarm at least once annually to remove dust, dirt and debris. Always

turn off the AC power to the heat alarm before cleaning it.

Using the soft brush or wand attachment to a vacuum cleaner, vacuum all sides and

the cover of the heat alarm. Be sure that all vents are free from debris. If necessary,

turn off the AC power and use a cloth dampened with warm water to clean the heat

alarm cover.

IMPORTANT: Do not attempt to remove the cover or clean inside the heat alarm.

THIS WILL INVALIDATE YOUR GUARANTEE. Failure to properly clean and maintain

this heat alarm may result in impaired operation and possible failure and will invali-

date the guarantee.

WARNING: BATTERIES NOT REP ACEAB E IN THE KF30 ORKF30R.

MODE KF30R HAS PERMANENT Y MOUNTED RECHARGEAB E ITHIUM BATTERIES THAT ARE DESIGNED

TO AST THE USEFU IFE OF THE A ARM.

BATTERY REPLACEMENT– KF30 ONLY

Always turn off the AC power to the heat alarm before replacing the battery. Replace

the battery at least once annually, or immediately when the low battery signal

sounds once a minute, even though the heat alarm is receiving AC power. Use only

the following batteries as replacements in this heat alarm: Energizer 522 ; Duracell

MN1604 or MX 1604; FD CP-V9Ju; Ultralife U9VL-J-P.

CAUTION: DANGER OF EXP OSION IF BATTERY IS INCORRECT Y REP ACED.USE ON Y THE BATTERIES

SPECIFIED IN THE USER USER GUIDE.

WARNING: DO NOT USE ANY OTHER TYPE OF BATTERY,EXCEPT AS SPECIFIED IN THIS USER GUIDE. DO

NOT USE RECHARGEAB E BATTERIES.

1. Turn off the AC power supply to the heat alarm at the main distribution board.

2. Insert a small screwdriver into the slot in the mounting plate and turn the heat

alarm counterclockwise to detach the alarm.

3. Gently pull down the heat alarm. Be careful not to separate any wire connections.

4. Pull out the connector plug from the back of the heat alarm.

5. From the back of the heat alarm, remove battery door screw and lift the tab to

open the battery compartment door.

6. Remove the battery from the compartment. Disconnect the drained battery

from the battery compartment and discard.

7. Connect a new, healthy 9V battery to the connector. The battery will fit only one

way. Be sure the battery connector is securely attached to the battery terminals.

8. Place the battery into the battery compartment.

9. Close the battery compartment door. Push down until it snaps into place. In-

stall battery door screw.

10. Using the TEST button, test the heat alarm to verify 9V DC battery back-up. See

TESTING THE HEAT ALARM.

11. Replace the connector plug. The connector will snap into place. Gently tug the

connector to be sure it is attached properly.

12. Reattach the heat alarm to the mounting plate by turning the heat alarm clock-

wise until it snaps into place.

13. Turn on the AC power and test the heat alarm using the TEST button. See

TESTING THE HEAT ALARM.

REPAIR

CAUTION: DO NOT ATTEMPT TO REPAIR THIS HEAT A ARM. DOING SO WI INVA IDATE YOUR GUARANTEE.

If the heat alarm is not operating properly, see TROUBLESHOOTING. If necessary,

and if the heat alarm is still under warrant, pack it in a well-padded carton and send

it, with Proof of Purchase postage prepaid, to the address given at the end of this

user guide.

If the heat alarm is no longer under guarantee, have a qualified electrician replace

the heat alarm immediately with a comparable Firex brand heat alarm.

INTERCONNECTING HEAT ALARMS

Use 1.5mm2 minimum solid or stranded cable with a rating of 230V. When intercon-

necting heat alarms, CO alarms or smoke alarms, the maximum cable length

between anytwo should be 450m for 1.5mm2 cable (20 ohm loop resistance.)

DO NOT connect to any other type or model of heat alarm, CO alarms or smoke

alarm. Connect all interconnected heat and smoke alarms to a single final circuit.

Wiring must conform to I.E.E. Regulations for Electrical Installations (BS 7671).

RED AND GREEN LED INDICATORS

This heat alarm features a red and green LED indicator that can be seen through the

clear light pipe on the top of alarm. The LEDs indicate the following:

GREEN

ON – AC power is present.

OFF – AC power is not present.

RED

BLIN S ONCE EVERYA 5 MINUTES AND 20 SECONDS – Mains power is

present indicating normal operation.

BLIN S ONCE EVERY 10 SECONDS – False Alarm Control activated.

OFF – DC power is not present.

BLIN S ONCE A SECOND and unit is sounding alarm – senses 57°C

temperature or greater.

OFF and unit is sounding alarm – Another interconnected smoke/heat alarm in

the network has sensed smoke or 57°C and is signaling this alarm.

3 RAPID FLASHES AT 40 SECOND INTERVAL - Indicates which alarm has

previously detected an alarm condition.

HUSH CONTROL

WARNING: BEFORE USING THE A ARM’S HUSH FEATURE, FU Y IDENTIFY THE

SOURCE OF THE HEAT BUI D UP AND MAKE SURE THAT THE AREA IS SAFE.

TO ACTIVATE CONTRO PUSH AND RE EASE THE TEST/FA SE A ARM CONTRO

BUTTON IN THE CENTER OF THE A ARM. THE A ARM WI SI ENCE IMMEDIATE Y

AND THE RED IGHT ( ED) WI B INK APPROXIMATE Y EVERY 10 SECONDS FOR

THE NEXT 10 MINUTES. THIS FEATURE IS TO BE USED ON Y WHEN A SAFE CONDI-

TION IS KNOWN TO EXIST.

The Hush feature will silence the alarm for approximately 9 minutes. A rapid rise in

temperature will override the False Alarm Control and cause the unitto sound an

alarm.

After 9 minutes the heat alarm will revert to normal operation. If the unit still detects

a dangerous situation the alarm will sound again.

If interconnected alarms are installed, the unit that detects the high temperature

and sounds the alarm cannot be inadvertently silenced by the TEST/Hush button of

other units. In this case all of the alarms will continue to sound for as long as a dan-

gerous situation is detected or until the TEST/Hush button of the initiating alarm is

pressed.

If the alarm does not go into False Alarm Control and continues to sound its alarm,

the heat in the area is too high and a dangerous situation may exist – take

emergency action.

TESTING THE HEAT ALARM

WARNING: TEST EACH HEAT A ARM AND SMOKE A ARM TO BE SURE THAT EACH IS INSTA ED

CORRECT Y AND IS OPERATING PROPER Y.

STAND AT ARM’S ENGTH FROM THE HEAT A ARM WHEN TESTING. THE A ARM SOUNDER IS OUD TO

A ERT YOU TO AN EMERGENCY AND CAN BE HARMFU TO HEARING.

TEST THE HEAT A ARM WEEK Y AND UPON RETURNING FROM HO IDAY,OR WHEN THE HOUSE HAS BEEN

UNOCCUPIED FOR SEVERA DAYS.

Test all heat alarms weekly by doing the following:

1. Check the TEST/HUSH button. If the green LED above the

test button is ON, the heat alarm is receiving AC power.

ORANGE OR WHITE ORANGE OR WHITE

FOR INTERCONNECTING: USE A MINIMUM OF 1.5mm2CABLE

NEUTRAL

LINE

NOTE: Colors shown correspond to electrical codes in the United ingdom. Colors may

vary in other countries.

once every 40 seconds

3 chirps every 40 seconds

(KF30, KF30LL Only).

KF30R:

KF30

KF30LL: This alarm has a long life lithium

battery to last the full life of the alarm.

If the alarm beeps every 40 seconds

there is a unit fault and it needs replacing.

Ten (10) year end of life warning.

Alarm must be replaced

(REPLACE IMMEDIATELY! )

NOTE: PUSH AND HOLD TEST BUTTON

1003-7203-00

1003-7203-00_(KF30_KF30LL_KF30R)_V6a:_ 2015.2.4 10:07 AM Page 2

Autres manuels pour KF30

Ce manuel convient aux modèles suivants

Autres manuels Firex Système de sécurité

Firex

Firex FADCM Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur