Firegear FLEXFRAME-SS Manuel utilisateur
Model: FLEXFRAME-SS
Universal brackets for use with blocks, bricks or pavers to
support round, linear pans and fl at disc re pit burners
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL OR OPERATE THIS PRODUCT
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
Installation Instructions
CALIFORNIA PROPOSITION 65
WARNING
This product can expose you to Chromium, which is
known to the state of California to cause cancer
and birth defects or other reproductive harm.
(For more information, go to www.p65warnings.ca.gov)
REV. 8-24-18 Page 2
Flexframe
TWO AVAILABLE MODELS
FLEXFRAME-SS: Constructed of 16 guage 304 stainless steel. Engineered to protect against the outdoor elements
including salt water environment.
DESCRIPTION: Flexframe kit comes shipped in two pieces, 44-inches long. Each piece can be bent or cut to t any
shape (square, linear or round). It provides the means to support a re pit inside of an enclosure which enables a service
technician the ability to remove the media and easily lift the re pit out for service.
INSTALLATION
SPECIFICATIONS
6 ¼”
1 ⁄”
⁄”
5 ⁄”
Fig. 1 End view
STEP 1: Determine if the Flexframe will work for your application. Measure the outer dimension of the re pit and
compare it to the inner dimension of the enclosure. The Flexframe protrudes outward approximately ⅞” on the inside of
the enclosure to provide a lip to sit the re pit in place. NOTE: If an optional log set is purchased, additional support
(i.e. blocks stacked underneath the center of the re pit) may be required to support the extra weight.
STEP: 2 Refer to the installation manual of the re pit you are installing to ensure you maintain proper clerarances to the
ground. Lay the pavers or blocks to build your enclosure. When you have reached the minimum height (per re pit
manual) inside the enclosure install the Flexframe as shown in Fig. 2 or Fig 3. Ensure the Flexframe slides in as far as
possible until it stops at the rst bend.
READ THESE INSTRUCTIONS COMPLETELY THROUGH BEFORE PROCEEDING WITH INSTALLATION
Pavers
Flexframe
Pavers
Pavers
Pavers
Correct
Installation
Fig. 2 Correct Flexframe orientation
Pavers
Flexframe
Pavers
Pavers
Pavers
Correct
Installation
Fig. 3 Correct Flexframe orientation
REV. 8-24-18 Page 3
Flexframe
If you are building a round paver enclosure the fl exframe will easily bend by hand in virtually any shape you perfer (Fig. 4).
CAUTION: Wear gloves when forming the fl exframe by hand. The fl ex frame could “spring” back and pinch ngers.
In addition it is a good idea not to form the fl exframe until you are ready to lay it into place. This will allow your block or
pavers to hold it into place as you are completing the top row. Note: If you feel the need for additional strengthening then
add block adhesive to the same layer with the Flexframe for extra support.
Fig. 4 Bend the Flexframe by hand
STEP 3: Form or lay the Flexframe inside the entire enclosure area. It is permissible to cut the Flexframe to t your
enclosure, however, it is not permissible to only use “just enough” pieces to support a pan (See Fig. 5 andf Fig. 6 for
examples).
NOTE: Firegear Outdoors will not be liable for Flexframe installations not installed correctly. Once the Flexframe is in
place the installation is complete. Proceed to Step 4 for re pit installation.
Correct
Installation
Wrong
Installation
Fig. 5 Flexframe round installation
REV. 8-24-18 Page 4
Flexframe
STEP 4:
Double check the minimum height above ground level before installing the re pit. Complete the installation by installing a
re pit, pan or disc on the lip area of the Flexframe (See Fig. 7 and Fig. 8). After test re is complete cover the burner with
media as described in the re pit installation manual.
Correct
Installation
Wrong
Installation
Fig. 6 Flexframe square/rectangle installation
Fig. 7 Flexframe complete Fig. 8 Flexframe shown with re pit installed
FOR TECHNICAL SERVICE, CALL:
Firegear Outdoors
9230 Conservation Way
Fort Wayne, IN 46809
Sales: (888) 672-8929
WEB SITE:
www.firegearoutdoors.com
(855) 498-8324
Table des matières
Autres manuels Firegear Cheminée extérieure
Firegear
Firegear LOF-2412HTPSI-N Manuel utilisateur
Firegear
Firegear RTF-R36 Manuel utilisateur
Firegear
Firegear Kalea Bay OFP-36LECO-N Manuel utilisateur
Firegear
Firegear FPB-26DBSMT-N-SAN Manuel utilisateur
Firegear
Firegear FPB-19 AFEI/N Manuel utilisateur
Firegear
Firegear VENT KIT 6x12 Manuel utilisateur
Firegear
Firegear ANF-R42 Manuel utilisateur
Firegear
Firegear LOF-2412HAWS-N Manuel
Firegear
Firegear LOF-30MT Manuel utilisateur
Firegear
Firegear KWB-NG1 Guide de démarrage rapide
Firegear
Firegear PRO Series Manuel utilisateur
Firegear
Firegear SAN2-34DBSAWSN Series Manuel utilisateur
Firegear
Firegear FPB-19MT/N Manuel utilisateur
Firegear
Firegear LOF-2414FHMT-N Manuel utilisateur
Firegear
Firegear PRO Series Manuel utilisateur
Firegear
Firegear LUME-MS1 Manuel utilisateur
Firegear
Firegear FPB-G25RBSTMS-N Manuel utilisateur
Firegear
Firegear LOF-4214HMT-N Manuel utilisateur
Firegear
Firegear PRO Series Manuel utilisateur
Firegear
Firegear FPB-19RBSTMSI-N Manuel utilisateur
