FireAngel W2-SVP-630 Manuel utilisateur
User Manual
COMBINED STROBE
& VIBRATING PAD
W2-SVP-630
Please read me – as I could save your life.
Please retain this user manual for future reference
Keeping you safe from re and carbon monoxide
For a full range of smoke alarms and carbon monoxide alarms
visit www. reangel.co.uk
CONTENTS
Note: This User Manual is also available in large text and other
formats. Please call 0800 141 2561 for further information
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLING THE STROBE AND VIBRATING PAD . . . . . . . 4
CONNECTING THE BATTERY/MAINS POWER . . . . . . . . . 4
WIRELESSLY INTERLINKING THE
WI-SAFE 2 STROBE AND PAD TO YOUR
WI-SAFE 2 SMOKE OR CO ALARM . . . . . . . . . . . . . . . 6
TESTING THE WI-SAFE 2 STROBE AND
VIBRATING PAD WITH SMOKE/CO ALARMS . . . . . . . . . 7
POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTALLING THE STROBE . . . . . . . . . . . . . . . . . . . . 10
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
UNPLUGGING FROM THE MAINS/POWER CUT . . . . . . 13
PRODUCT INDICATORS (LEDS) . . . . . . . . . . . . . . . . 14
WHAT TO DO IF YOUR STROBE AND
VIBRATING PAD GOES INTO ALARM . . . . . . . . . . . . . 15
WHAT TO DO IN THE EVENT OF
A SMOKE ALARM TRIGGERING
THE STROBE AND PAD . . . . . . . . . . . . . . . . . . . . . 16
WHAT TO DO IN THE EVENT OF
A CARBON MONOXIDE ALARM
TRIGGERING THE STROBE AND PAD . . . . . . . . . . . . . 17
REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . 19
DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RETURNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PRODUCT RANGE . . . . . . . . . . . . . . . . . . . . . . . . 21
2
INTRODUCTION
KEY FEATURES
IMPORTANT: If you are installing this product for
use by others, you must leave this manual (or a
copy of it) for the end user.
Wi-Safe 2 is the very latest in wireless technology from
Sprue Safety Products. It provides a network of wireless
radio frequency (RF) communication which can trigger
Wi-Safe 2 Alert products to alarm in the event of danger.
This Strobe and Vibrating Pad, when interlinked with
Wi-Safe 2 enabled Smoke alarms and/or Wi-safe 2
enabled Carbon Monoxide (CO) Alarms (purchased
separately) will provide warning of danger from smoke
and/or carbon monoxide.
In addition to the audible sound from the Smoke (or
CO) alarm, the ashing Strobe and Vibrating Pad will be
triggered to alert someone who may not be able to hear
the audible alarm. The ashing strobe provides a visual
warning for waking hours, while the vibrating pad is
designed to be placed under a pillow or a mattress and
is suitable for waking an individual to alert them when a
smoke alarm sounds. If placed under a mattress, ensure
the thickness of the mattress does not cushion the pad
to the extent it cannot be felt adequately.
• Uses Wi-Safe 2 technology to provide warning of re
or Carbon Monoxide (CO). Wi-Safe 2 products can
be interlinked to create a network, meaning if smoke
or CO triggers any alarm in the network, all other
networked alarms and ancillary devices activate.
• When used with Wi-Safe 2 enabled Smoke and/or CO
alarms, the kit provides additional protection when
sound alone may not be enough.
• Provides a simple two button press “learn in” process
3
to wirelessly interlink with Wi-Safe 2 smoke alarms or
CO alarms.
• The Strobe provides a remote low level testing
facility for testing interlinked smoke and CO alarms,
avoiding the need to reach up to ceiling mounted
alarms to test.
• Mains powered with rechargable battery back-up
(must be replaced after 5 years).
• The Strobe will detect and demonstrate a fault or low
battery warning with any smoke alarm or CO alarm
within the inter-linked network.
• The Strobe is suitable for wall mounting with 2 screw
xings or free standing.
• Designed for use with Smoke alarms and Carbon
Monoxide alarms from the Wi-Safe 2 range
(purchased separately).
Wi-Safe 2 Strobe and Vibrating Pad Pack contains:
1. CP-STROBE - Strobe light with integrated control
unit (referred to as “strobe”)
2. CP-VPAD - Vibrating pad to be placed under pillow
or chair (referred to as ”pad”)
3. AD-DC12V05A - AC mains adaptor, 12v, 0.5A
rated output
4. B-450L - Replaceable, rechargeable 5 year
life battery
5. Wall xing screws
NOTE: The Strobe and Vibrating Pad is only compatible
with Wi-Safe 2 alarms from Sprue Safety Products. It
cannot be wirelessly interlinked with other models or
brands of smoke alarms or carbon monoxide alarms.
It is not compatible with products from Sprue Safety
Products original Wi-Safe range.
The Wi-Safe 2 product range is currently being
expanded. Please visit www.reangel.co.uk for
details of the latest additions to the portfolio.
4
INSTALLING THE STROBE
AND VIBRATING PAD CONNECTING THE
BATTERY/MAINS POWER
PREPARATION: Please ensure you have read and
understood this entire manual before installing your Strobe
and Vibrating Pad.
Your Strobe and Vibrating Pad is designed to be used in
conjunction with Smoke alarm(s) and CO alarm(s) from
the Wi-Safe 2 range of products. It is recommended that
for optimum protection from smoke and/or carbon
monoxide, one Wi-Safe 2 smoke alarm is tted in each
living room of your home, including bedrooms, and one
Wi-Safe 2 CO alarm is tted in every room containing a fossil
fuel appliance, connected to your Strobe and Vibrating Pad.
NOTE: Up to fty Wi-Safe 2 enabled Smoke alarms, CO
alarms and/or Wi-Safe 2 accessories can be interlinked
(“learned in”) to a single network
Ensure all smoke alarms and/or CO alarms to be used
are installed, tested and working correctly as per the
instructions in their respective user manuals.
It is possible to use the strobe independently. For further
details please contact Technical Support on: 0800 141 2561
NOTE: The Strobe and Vibrating Pad requires both a
continuously powered AC (mains) electrical supply
and internal battery for its normal operation. The
battery accompanying this product is rechargeable and
charges when there is mains power to the Strobe.
1. Plug the Vibrating Pad connector into the Strobe
(as shown in g1) Route the wires through the wire
guide.
fig1
5
NOTE: When power is rst provided to the Strobe,
the amber LED and both red LEDs will ash twice and
the unit will ‘bleep’ three times; the amber LED will
then illuminate continuously to indicate that the unit
has not been “learned in” to any network. Both alarm
LED’s (smoke and CO) will extinguish. This will typically
happen when the battery is connected. If the battery
does not retain any residual charge, it will happen when
the mains power is connected.
2. Remove the battery cover on the back of the Strobe
by pulling back the clip to release. Connect the
rechargeable battery, by aligning the terminals
(red wire to red wire) and clipping the connectors
together. You may hear the Strobe chirp as you do
this.
7. Plug the mains adaptor into a 230V socket and
turn the power on. The green power LED should
illuminate.
6. Plug the power cable in to the Strobe. Route the
wire through the wire guide (g3).
3. Place the battery into the recess. NB: the battery
cable needs to be positioned underneath the
battery. Place the cable at the bottom of the recess
with the battery lying over the top with the text
on the battery face down. This will ensure that the
battery is installed correctly.
5. Assemble the power cable and adaptor by
positioning the plug head as shown. Rotate onto the
adaptor clockwise until it clicks into position. (g2)
4. Replace the battery cover.
CAUTION: Connect the battery with mains
power disconnected.
fig2 fig3
6
WIRELESSLY INTERLINKING
THE WI-SAFE 2 STROBE AND
VIBRATING PAD TO YOUR
WI-SAFE 2 SMOKE OR CO ALARM
It is recommended that you read through these “learn
in” instructions before starting.
Learning a Strobe into a new Wi-safe 2 system:
Learning a strobe into an existing Wi-Safe 2 system:
1. Place one of your Smoke or CO alarms on to its
baseplate. You will use this product to interlink with
the strobe to create a network.
2. Briey push and release the learn button located in
a circular hole in the back of the Strobe, using a ball
point pen or similar pointed instrument (g4). 1. Locate a Smoke / CO alarm that is already part of the
existing Wi-Safe 2 system. You will use this product
when adding the strobe into the network
2. Follow steps from point 2 above
3. After pressing this button, the two Alarm (red) LEDs
on the front of the unit will ash and then illuminate
for 5 seconds.
4. During this period, while the red LEDs are
illuminated, press the test/reset button on the
Smoke or CO alarm to wirelessly interlink the two
products.The Smoke alarm (or CO alarm) will emit
an audible signal, and the red (Alarm) LED on the
Smoke (or CO alarm) will also ash.
5. After learning in the Strobe and Vibrating Pad into
the alarms, test the units individually to ensure they
are wirelessly interlinked (see below)
To add any further alarms to the network, press the
learn button on the new alarm then the test button on
the Strobe, or on any alarm already learned in to the
network.
fig4
7
NOTE: The battery is supplied in a discharged or
partially discharged state and will require up to 24
hours of charging (continuous connection to the
mains supply) to ensure that it is fully charged. During
this period the amber fault LED may ash once every
ve seconds to indicate that the battery is low. The
following tests however may be carried out before the
charging is complete.
Further Wi-Safe 2 products (including additional
Strobes) can be learned into the network in the same
way. The learn button on the Strobe is located on the
back of the product.
NOTE: The amber fault LED will also ash (once per
second) if the Vibrating pad is not correctly installed.
After learning in the Strobe and Vibrating Pad into the
alarms, test the units individually to ensure they are
wirelessly interlinked (see next section)
To remove (“unlearn”) the Strobe from the wireless
network:
1. Briey push and release the learn button located in
the circular hole in the back of the Strobe as shown
(g 4). The two red alarm LEDs on the front of the
Strobe will illuminate as you push the button.
2. Push and hold the learn button a second time. The
red alarm LEDs will illuminate. Hold the button until
the red alarm LEDs extinguish.
3. The red alarm LEDs will then perform a sequence of
two long and three short ashes. The yellow fault
LED will illuminate continuously to conrm that the
the Strobe is no longer interlinked to the wireless
network.
4. Press the test button on the Strobe. It should not
cause other Wi-Safe 2 alarms to sound. However,
if the Strobe is still interlinked, repeat the above
procedure.
IMPORTANT: If you wish to remove the Strobe
and Vibrating Pad from the wireless network, it
is important to “unlearn” the unit from the network.
Failure to do so means that the unit continues to try
and communicate with the removed unit, and will
result in a system fault.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels FireAngel Alarme incendie
