Fike FIK-RA2000 Manuel technique
PN LS10261-001FK-E:B 5/25/2022 ECN: 00003636
FIK-RA2000 Annunciator
Product Installation Document
FIKE CORPORATION
704 SW 10th Street
Blue Springs, MO 64015
www.fike.com
1 Description
The FIK-RA2000 is an optional 4x40 remote annunciator that can be
surface or flush-mounted.
1.1 Compatibility
The FIK-RA2000 is compatible with the Fike Series FACPs. For more
information, refer to the FACP Manual.
1.2 Specifications
2 Installation
1. Ensure power is turned off at the panel.
2. Mount the FIK-RA2000 in the desired location. See Section 2.1.
3. Connect the FIK-RA2000 to the panel. See Figure 5.
4. Use the DIP switches on the back of the FIK-RA2000 to assign an
ID number. Refer to the FACP manual.
5. The FIK-RA2000 module must be added to the system through
FACP programming. JumpStart can be used to automatically add
the module or it may be added manually. Refer to the FACP Manual
for more information.
2.1 Mounting
2.1.1 Flush Mounting
Follow these steps to flush mount the FIK-RA2000.
1. The backbox dimensions are 9.25” W x 8.375” H. The minimum
depth required is 2". Mount the backbox using the mounting holes
shown below.
2. Remove knockouts as needed for wires. There are 10 knockouts
available, two on each side and two in the back of the cabinet.
3. Wire the annunciator board to the main control panel as shown in
Figure 5.
4. Attach the annunciator and door assembly to back box as shown
below using the supplied screws.
Operating Voltage: 24VDC
Current Standby Current: 27mA
Alarm Current: 53mA
Operating Temperature: 32° to 120° F (0° to 49° C)
Dimensions Flush Mount: Overall:
12.25” W x 11.5” H x 0.875” D
(31.1 cm W x 29.2 cm H x 2.2 cm D)
Backbox: 9.25” W x 8.375”H
(23.5cm W x 21.27cm H)
Surface Mount: Including trim ring:
12.25” W x 11.5” H x 3.0” D
(31.1 cm W x 29.2 cm H x 7.6 cm D)
Table 1 Specifications
BACK BACK BACK
NEXT NEXT NEXT
Figure 1 FIK-RA2000 Remote Annunciator
mounting holes
mounting holes
Figure 2 FIK-RA2000 Backbox Mounting
Figure 3 Attaching Annunciator/Door Assembly
2FIK-RA2000 Installation Document — P/N LS10261-001FK-E:B 5/25/2022
2.1.2 Surface Mounting
The RA-100TR Red Trim Ring kit is available for use when surface
mounting the FIK-RA2000.
1. Remove the desired knockout.
2. Mark and pre-drill hole in the wall for the center top keyhole
mounting bolt. Refer to Figure 2 for mounting hole locations.
3. Install center top fastener in the wall with the screw head
protruding.
4. Place backbox over the top screw, level and secure.
5. Mark and drill the left and right upper and lower mounting holes.
6. Install remaining fasteners and tighten.
7. Run wires to the control panel. Refer to Figure 5.
8. Place the trim ring over the back box as shown below.
9. Attach the door assembly to the backbox using the screws provided.
Refer to Figure 3.
3 Wiring Connections
Wire the FIK-RA2000 to the FACP as shown in below.
Figure 4 Installing Trim Ring
SBUS OUT
–+AB
S– S+ AB
ON
12345
6
DIP Switches
remote annunciator
(back view)
supervised,
power-limited,
Class B
Figure 5 SBUS Connections
Ce manuel convient aux modèles suivants
1
Autres manuels Fike Système de conférence
Manuels Système de conférence populaires d'autres marques
Kramer
Kramer VIA GO Manuel utilisateur
AVT
AVT MAGIC AC1 Go Manuel utilisateur
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur
Sony
Sony PCS-I150 Manuel utilisateur
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuel utilisateur
Prentke Romich Company
Prentke Romich Company Vanguard Plus Mode d’emploi
