Fife MAXCESS SE-26B Manuel utilisateur

FIFE GUIDING SOLUTIONS

FIFE SE-26B

Operating Instructions

Line Guide Sensor

MI 1085 1

ICONTENTS

SE-26B www.maxcess.euMI 1085 1

INSTRUCTION 1-1

About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Improper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Operating principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

SAFETY INSTRUCTIONS 2-1

Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Information about safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Preventing hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Installation and commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

INSTALLATION 3-1

Transport and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Mechanical fastening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Fine adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Changing the sensor alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Mounting arrangement with different materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

COMMISSIONING 4-1

Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Preparation of the web guide controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

OPERATION 5-1

Selecting suitable references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Setting up references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Preconditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

D-MAX(E) WITH OPERATOR INTERFACE OI-TS 6-1

Preparing the controller for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Select sensor type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Selecting a reference type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Setting up the ASC function with broken line/edges . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Setting up references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Setting up a (broken) line as a reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Setting up a (broken) material or print edge as a reference . . . . . . . . . . . . . . . . . . . 6-5

D-MAX(E) WITH OPERATOR INTERFACE OI-N 7-1

Preparing the controller for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Select sensor type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Selecting a reference type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Setting up the ASC function with broken line/edges . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Setting up references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Setting up a (broken) line as a reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Setting up a (broken) material or print edge as a reference . . . . . . . . . . . . . . . . . . . 7-5

IICONTENTS

SE-26Bwww.maxcess.eu MI 1085 1

MI10851-IVZ.fm

DP-20/DP-30 8-1

Preparing the controller for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Select sensor type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Selecting a reference type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Setting up the ASC function with broken line/edges . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Setting up references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Setting up a (broken) line as a reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Setting up a (broken) material or print edge as a reference . . . . . . . . . . . . . . . . . . 8-5

FIFE-500 9-1

Preparing the controller for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Select sensor type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Selecting a reference type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Setting up references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Setting up a (broken) line as a reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Setting up a (broken) material or print edge as a reference . . . . . . . . . . . . . . . . . . 9-5

MAINTENANCE 10-1

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

TROUBLESHOOTING 11-1

TECHNICAL DATA 12-1

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

Optical properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2

SERVICE 13-1

Requests for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

Adresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

INSTRUCTION1 - 1

SE-26B www.maxcess.euMI 1085 1

1 INSTRUCTION

About these operating

instructions These operating instructions describe the installation,

commissioning, operation and maintenance of the SE-26B line

sensor and provide important instructions for proper use.

These operating instructions are intended for both the system

construction master as well as the operator who uses the

SE-26B sensor in production. The Operating Instructions must

be read and applied by everyone who is responsible for

installation, commissioning, operating or maintaining the

SE-26B sensor.

The Operating Instructions must be carefully kept and must

always be available throughout the service life of the SE-26B

sensor.

Translation of the original Operating Manual:

This Operating Manual is a translation. The original Operating

Manual was composed in German.

Proper use The SE-26B line sensor is intended for use on machines or

systems. It is used for no-contact measurements of the lateral

offset of a material web that is being guided. The SE-26B sensor

is suitable for

– center guiding on a thin printed line.

– edge guiding on a printed line.

– guiding on a material edge.

Guiding is also possible with dashed lines, discontinuous

pattern or discontinuous edges. The free spaces between the

lines or pattern must not be too large, since guiding is blocked

during that time.

The SE-26B works reliably with smooth, rough, dull or glossy

material surfaces. This sensor can also be used with low color

contrast between the background and printed line.

The SE-26B sensor must only be used in accordance with its

intended purpose and in a technically flawless conditions.

INSTRUCTION 1 - 2

SE-26Bwww.maxcess.eu MI 1085 1

Einführung.fm

Improper use – Operation outside of the technical specifications is not

permitted.

– Operation in areas where there is a danger of explosions is

prohibited.

– Outdoor operation is not permitted.

– The SE-26B sensor may not be used as a support, handle or

step.

– Any use other than the designated use is not permitted.

Operating principle The SE-26B line sensor works with white LED light.

The light emitter in the SE-26B sensor generates a light spot on

the surface of the material being scanned. Differences in

contrast in this area will be sensed by the receiver. The

difference in contrast could be produced for example by a

printed line. In this case the line is the reference for control.

The lens and cover can be screwed off and replaced to change

the scanning direction.

Note:

The explanation in the sections on commissioning and

operation also apply to sensors SE-26 and SE-26A.

1Lens

2Cover

3Nameplate

4 Thread for sensor bracket

5 Connection cable to a

Fife controller

Figure 1.1: Line guiding sensor SE-26B

SAFETY INSTRUCTIONS2 - 1

SE-26B www.maxcess.euMI 1085 1

2 SAFETY INSTRUCTIONS

Important information Problem-free and reliable operation of the SE-26B requires that

the sensor

– properly shipped and stored,

– properly mounted and placed in operation,

– properly used and carefully maintained.

Proper operation and careful maintenance will ensure a long

service life for the sensor.

Only persons who are acquainted with the installation,

commissioning, operation and maintenance of the sensor and

who possess the necessary qualifications for their activities may

work on the sensor.

Please note the following:

– The content of these operating instructions

– The safety instructions printed on the unit

– The requirements of the machine manufacturer

– National, state and local requirements for accident

prevention and environmental protection

Information about

safety instructions The safety instructions and symbols described in this section

are used in these Operating instructions. They are used to avoid

possible dangers for users and to prevent material damage.

SIGNAL WORD

Source of danger and its results.

Avoiding dangers

The signal word WARNING refers to the danger of moderate to

sever bodily injuries.

The signal word CAUTION refers to the danger of slight to

moderate bodily injuries or material damage.

SAFETY INSTRUCTIONS 2 - 2

SE-26Bwww.maxcess.eu MI 1085 1

Sicherheit.fm

Symbols

Warning/caution - dangerous area

Reference to general hazards that may result in bodily injuries

or damage to the device

Warning/caution - danger due to crushing

Refers to danger of injury caused by crushing

Warning/caution - danger due to cutting

Refers to danger of injury caused by cutting

Additional symbols

– This endash is followed by an enumeration.

∙This dot is followed by a prompt to do something.

Note:

Reference to important information.

Preventing hazards ∙The SE-26B sensor may not be used as a support, handle or

step. There is a danger that the sensor will become damaged

(breaking off/snapping), resulting in personal injury.

Installation and

commissioning ∙A damaged sensor must not be installed or placed in

operation.

∙Assembly work must be performed while the machine is

stopped and protected against being turned on again.

∙All assembly tasks must only be performed when there is no

electrical power in the system.

∙The sensor must not be placed in operation unless it has

been securely mounted.

∙Electrical connections should always be made or

disconnected on the sensor while there is no electrical power

in the system. Failure to observe these instruction may result

in damage to the sensor.

SAFETY INSTRUCTIONS2 - 3

SE-26B www.maxcess.euMI 1085 1

∙The parameters specified in Section

Technical Data

must be

observed.

∙Only replacement parts that have been approved by

Fife-Tidland may be used.

∙No changes must be made to the sensor.

∙Electrical lines must not be subjected to any mechanical

loads.

Operation

∙Danger of injury by crushing

Do not place your hands on or near moving parts (rollers,

material web, etc.) during operation.

∙Danger of injury due to cutting on the edge of the material

web

Do not place your hands on the edge of the (moving)

material web during operation.

Maintenance

∙Danger of injury by crushing



Maintenance work must only be performed on the sensor

when the power is turned off, the machine is stopped, and it

is protected against being turned back on.

INSTALLATION 3 - 1

SE-26Bwww.maxcess.eu MI 1085 1

Montage.fm

3 INSTALLATION

Transport and storage – The sensor and/or the unit on which the sensor is mounted

must be secured against slipping during transport.

– The sensor must be stored in a cool, dry place.

– The sensor must not be stored in the vicinity of powerful

magnetic fields. The electronic components of the sensor

may be damaged.

Scope of delivery –SensorSE-26B

The model designation and the serial and part number are on

the nameplates on the housing.

see item 3 in

Figure 1.1, page 1-2

– Operating Instructions

Mounting

WARNING

All assembly tasks on the sensor must be performed when

there is no electrical power in the system.

Assembly tasks and mechanical settings must only be

performed when the machine has been stopped and has been

secured from being turned on again.

INSTALLATION3 - 2

SE-26B www.maxcess.euMI 1085 1

Dimensions

Mounting location –ProtectionClass:IP65

– Operating temperature: 0°C ... 50°C

– Relative humidity: 5% to 85%

–Protectfromvibrations

– Not in the vicinity of strong magnetic fields

The electronic components may be damaged.

– Not in places where there is a risk of explosions

– Distance between lens and material being scanned:

approx. 10mm

– The material web must be guided in the area where the light

spot appears (guide point) by a support rod or support roller.

A plane change is not permitted.

– Protect the lens of the sensor against extraneous light.

72.73

53.3

40.3

25.3

99.4

M5-6 tief/deep

18.7



(4.5)

M5-6 tief/deep

1525.3

M5-6 tief/deep

A Cable length plus connector about 300 mm

Figure 3.1: SE-26B Dimensions

Table des matières

Autres manuels Fife Accessoires

Fife

Fife MAXCESS SE-42R Manuel utilisateur

Fife

Fife Maxcess DSE-45 Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur