FIBARO FGS-214 Manuel utilisateur
SMART MODULE
(FGS-214)
DOUBLE SMART MODULE
(FGS-224)
OPERATING
MANUAL EN
v1.0
3
Table of contents
1: Important safety information 4
2: Description and features 5
2.1: Description 5
2.2: Main features 5
3: Specications 6
4: Installation 7
4.1: Before installation 7
4.2: Electrical connection 8
5: Adding to Z-Wave network 9
5.1: Adding manually 9
5.2: Adding using SmartStart 9
6: Removing from Z-Wave network 10
7: Operating the device 11
7.1: Controlling channels with inputs 11
7.2: Visual indications 11
7.3: Menu 12
7.4: Resetting to factory defaults 12
8: Z-Wave range test 13
9: Activating scenes 14
10: Conguration 15
10.1: Associations 15
10.2: Advanced parameters 17
11: Z-Wave specication 27
12: Regulations 30
4
Important safety InformatIon
1: Important safety information
Read this manual before attempting to install the device!
!Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manu-
facturer, Fibar Group S.A. will not be held responsible for any loss or
damage resulting from not following the instructions of operating
manual.
DANGER OF ELECTROCUTION!
The device is designed to control other electrical devices and
operate in their housings. Faulty connection or use may result
in re or electric shock.
All works on the device may be performed only by a qualied
and licensed electrician. Observe national regulations.
Even when the device is turned o, voltage may be present at
its terminals. Any maintenance introducing changes into the
conguration of connections or the load must be always performed
with disabled fuse or power supply.
To avoid risk of electrical shock, do not operate the device with
wet or moist hands.
Do not modify!
!Do not modify this device in any way not included in this
manual.
Other devices
!The manufacturer, Fibar Group S.A. will not be held responsi-
ble for any damage or loss of warranty privileges for other con-
nected devices if the connection is not compliant with their
manuals.
This product is intended for indoor use only in dry locations.
!Do not use in damp or wet locations, near a bathtub, sink,
shower, swimming pool, or anywhere else where water or
moisture are present.
Not a toy!
!This product is not a toy. Keep away from children and
animals!
5
DescrIptIon anD features
2: Description and features
2.1: Description
The remotely operated FIBARO Smart Module and Double Smart
Module are designed to turn electrical devices or circuits on and o.
Smart Module allows to control one device or circuit and the Double
Smart Module allows to control two devices or circuits.
The compact size of the device allows for the product to be installed
in the housings of other devices. The devices can be controlled either
via the Z-Wave™ network or with buttons connected directly to them.
2.2: Main features
• Works with various types of switches and buttons.
• Supports Z-Wave network Security Modes: S0 with AES-128 en-
cryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater (all non-battery operated de-
vices within the network will act as repeaters to increase reliabili-
ty of the network).
• May be used with all devices certied with the Z-Wave Plus™ cer-
ticate and should be compatible with such devices produced by
other manufacturers.
The device is a Security Enabled Z-Wave Plus product
and a Security Enabled Z-Wave Controller must be
used in order to fully utilize the product.
i
6
specIfIcatIons
3: Specications
Power supply 100-240V~ 50/60Hz or 24-30V
Rated load current Smart Module (FGS-214):
6.5A
Double Smart Module (FGS-224):
6A per one channel
9.5A total
Compatible load types resistive or incandescent only
Active element micro-gap relay μ
Maximum length of wires 3 meters
Recommended wire
cross-section area
0.2–2.0mm2 (24–14 AWG)
(depending on load current)
Operating temperature 0–35°C
Ambient humidity 0–95% RH without condensation
Radio protocol Z-Wave (500 series chip)
Radio frequency band 868.0–868.6MHz; 869.7–870.0MHz
Max. transmitting power +5dBm
Range up to 50m outdoors
up to 40m indoors
(depending on terrain and building
structure)
Dimensions
(Height x Width x Depth)
42.5 x 38.25 x 20.3 mm
Classication of installa-
tion and use
Automatic electrical control for use in
equipment for household or similar
use
Mode of operation Type 1.B Action
Pollution degree 2
Software class Class A
Compliance with EU
directives
2011/65/EU
2015/863
2014/53/EU
Radio frequency of individual device must be same as
your Z-Wave controller. Check information on the box
or consult your dealer if you are not sure.
i
7
InstallatIon
4: Installation
4.1: Before installation
!Connecting the device in a manner inconsistent with this
manual may cause risk to health, life or material damage.
• Do not power the device before fully assembling it in the protect-
ed environment,
• Check the operating/maintenance manual of the device you want
to control to make sure the connection is safe and allowed,
• Connect only in accordance with the diagram,
• Always use the same power source for L and IN terminals,
• Do not connect devices which are not compliant with the speci-
cation or relevant safety standards,
• Do not install the device in metal boxes or on metal surfaces for
best radio performance.
Notes for diagrams:
S1 – terminal for 1st button
S2 – terminal for 2nd button
Q/Q1 – output terminal of the 1st channel
Q2 – output terminal of the 2nd channel
IN – input terminal for both channels
L – terminal for live wire
N – terminal for neutral wire
B – maintenance button
1 – device/system housing
2 – electrical device
8
InstallatIon
4.2: Electrical connection
1. Switch o the mains voltage (disable the fuse) or disable the
power supply.
2. Connect with one of the diagrams below:
BIN
L
24-30V DC
100-240V AC
NS1 S2
Q
SMART MODULE
FGS-214
1
2
Diagram 1: Example connection of Smart Module
BINQ1
L
24-30V DC
NS1 S2
Q2
DOUBLE
SMART MODULE
FGS-224
100-240V AC
1
2
Diagram 2: Example connection of Double Smart Module
3. Verify correctness of connection.
4. Tighten the terminal screws using PH1 screwdriver.
5. If the device fully assembled, switch on the mains voltage or
enable the power supply.
6. The LED light means the device is powered.
7. Add the device to the Z-Wave network (see the next chapter).
9
aDDIng to Z-Wave netWork
5: Adding to Z-Wave network
Adding (Inclusion) – Z-Wave device learning mode, allowing to add
the device to existing Z-Wave network.
5.1: Adding manually
To add the device to the Z-Wave network manually:
1. Power the device.
2. Set the main controller in (Security/non-Security Mode) add mode
(see the controller’s manual).
3. Quickly, three times click button connected to S1/S2 or the
maintenance button.
4. LED will start blinking yellow, wait for the adding process to end.
5. If you are adding in Security S2 Authenticated, input the underlined
part of the DSK (label on the bottom of the box).
6. Adding result will be conrmed by the Z-Wave controller’s message
and the LED:
• Green – successful (non-secure, S0, S2 non-authenticated),
• Magenta – successful (Security S2 Authenticated),
• Red – not successful.
5.2: Adding using SmartStart
SmartStart enabled products can be added into a Z-Wave
network by scanning the Z-Wave QR Code present on the
product with a controller providing SmartStart inclusion.
SmartStart product will be added automatically within 10 minutes of
being switched on in the network range.
To add the device to the Z-Wave network using SmartStart:
1. To use SmartStart your controller needs to support Security S2
(see the controller’s manual).
2. Enter the full DSK string code to your controller. If your controller
is capable of QR scanning, scan the QR code placed on the box or
the device label.
3. Power the device.
4. Wait for the adding process to start (up to few minutes), which is
signalled with yellow LED blinking.
10
removIng from Z-Wave netWork
5. Adding result will be conrmed by the Z-Wave controller’s message
and the LED:
• Green – successful (non-secure, S0, S2 non-authenticated),
• Magenta – successful (Security S2 Authenticated),
• Red – not successful.
i
In case of problems with adding the device, please re-
set the device and repeat the adding procedure.
6: Removing from Z-Wave network
Removing (Exclusion) – Z-Wave device learning mode, allowing to
remove the device from existing Z-Wave network. Removing also re-
sults in resetting the device to factory defaults.
!Make sure that restoring the parameters to factory
defaults will not result in damaging the connected
device, we recommend disconnecting it rst.
To remove the device from the Z-Wave network:
1. Power the device.
2. Set the main controller into remove mode (see the controller’s
manual).
3. Quickly, three times click the maintenance button.
4. LED will start blinking yellow, wait for the removing process to
end.
5. Successful removing will be conrmed by the Z-Wave controller’s
message and red LED colour.
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels FIBARO Contrôleurs
FIBARO
FIBARO FIBEFGWCEU-201-B Manuel utilisateur
FIBARO
FIBARO THE BUTTON Manuel utilisateur
FIBARO
FIBARO FGPB-101 Manuel utilisateur
FIBARO
FIBARO FGPB-101-5 Manuel utilisateur
FIBARO
FIBARO SWIPE FGGC-001 Manuel utilisateur
FIBARO
FIBARO KEYFOB FGKF-601 Manuel utilisateur
FIBARO
FIBARO ROLLER SHUTTER 2 Manuel utilisateur
FIBARO
FIBARO FGPB-101 Manuel utilisateur
FIBARO
FIBARO FGPB-101 Manuel utilisateur
FIBARO
FIBARO RGBW Controller Manuel utilisateur
FIBARO
FIBARO RGBW CONTROLLER 2 Manuel utilisateur
FIBARO
FIBARO ROLLER SHUTTER 3 Manuel utilisateur
FIBARO
FIBARO FGBHRGBW-041-1 Manuel utilisateur
FIBARO
FIBARO WALLI FGWCEU-201 Manuel utilisateur
FIBARO
FIBARO FGRGBW-442 Manuel utilisateur
FIBARO
FIBARO ROLLER SHUTTER 2 Manuel utilisateur
FIBARO
FIBARO Home Center Lite Manuel utilisateur
FIBARO
FIBARO SWIPE FGGC-001 Manuel utilisateur
FIBARO
FIBARO FGRGBWM-441 Manuel utilisateur
