Festo SPC200 Series Manuel utilisateur
Manual
Function block
SPC200−PC for
Simatic S7
SPC200 Smart Positioning Controller
Manual
540 189
en 0609a
[710 241]
Contents and general instructions
I
Festo P.BE−SPC200−S7−PC−EN en 0609a
Original de. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edition en 0609a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Designation P.BE−SPC200−S7−PC−EN. . . . . . . . . . . . . . . . . . .
© (Festo AG&Co. KG, D73726 Esslingen, Federal Republic
of Germany, 2006)
Internet: http://www.festo.com
e−mail: service_international@festo.com
The reproduction, distribution and utilization of this docu
ment as well as the communicaton of its contents to others
without express authorization is prohibited. Offenders will
be held liable for the payment of damages. All rights reser
ved in the event of the grant of a patent, utility module or
design.
Contents and general instructions
II Festo P.BE−SPC200−S7−PC−EN en 0609a
PROFIBUS®is a registered trademark of PROFIBUS International.
SIMATIC®is a registered trademark of Siemens AG
Contents and general instructions
III
Festo P.BE−SPC200−S7−PC−EN en 0609a
Contents
Designated use V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic principles of programmed software VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Target group VI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important user instructions VII. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
References to necessary SPC200 manuals IX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Installation of the function block 1−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Incorporating the function block in your project 1−3. . . . . . . . . . . . . . . . . . . . . .
2. Function block description 2−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Symbolic representation of the function block 2−3. . . . . . . . . . . . . . . . . . . . . . . .
2.2 Working method 2−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Input parameters 2−4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Output parameters 2−6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Reaction to start 2−7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6 Reaction to reset 2−9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7 Fault word 2−11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8 Parameters of the SPC200 2−15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents and general instructions
V
Festo P.BE−SPC200−S7−PC−EN en 0609a
Designated use
Function block SPC200−PC" serves for reading and writing
parameters of the SPC200 from a Simatic S7 controller with
PROFIBUS. For this purpose it uses the SPC200 parameter
channel (PC = parameter channel). The SPC200 must be
connected to the S7 by means of field bus module type
SPC200−COM−PDP.
Basic components and modules for the SPC200 are described
in the user manual type P.BE−SPC200−... . The safety
instructions specified in the manuals must always be
observed and the relevant components and modules must
only be used as intended. Please observe also the safety
instructions listed in the operating instructions for the
pneumatic components used. The SPC200 and the modules
and cables to be connected are only to be used as follows:
inaccordance with designated use
only in industrial applications
without any modifications by the user. Only the conver
sions or modifications described in the documentation
supplied with the product are permitted.
infaultless technical condition.
When used together with commercially available compo
nents, such as sensors and actuators, the specified limits for
pressures, temperatures, electrical data, torques etc. must be
observed. National and local safety regulations must also be
observed.
Note also the Siemens specifications regarding the use of
their PLC Simatic S7.
Contents and general instructions
VI Festo P.BE−SPC200−S7−PC−EN en 0609a
Basic principles of programmed software
Please note that it is not possible with the present state of
technology to create programmed software which functions
without problems and is compatible with all applications and
combinations intended by the user.
As a rule the software must therefore be used in the desig
nated manner as specified in the program description and in
the user instructions.
At the moment when the software is transferred or made
available, it is in a state in which it will function under normal
operating and application conditions.
Festo does not guarantee that the software will suffice for all
applications and purposes intended by the user, or that it will
function without problems when used with other programs,
or that it is compatible with these programs. The responsibil
ity for the correct selection and the consequences of using
the software within the scope of use defined by the user, as
well as for the intended and achieved results therefore lies
with the user. The same applies to the written material sup
plied with the software.
The use of the programmed software does not exempt you as
customer from your duties and responsibility for observing
and adhering to technical machine and safety regulations as
well as for a comprehensive functional check.
Target group
This manual is intended exclusively for technicians trained in
control and automation technology, who have experience in
installing, commissioning, programming and diagnosing
PROFIBUS−DP slaves.
Contents and general instructions
VII
Festo P.BE−SPC200−S7−PC−EN en 0609a
Important user instructions
Danger categories
This manual contains instructions on the possible dangers
which may occur if the product is not used correctly. These
instructions are marked (Warning, Caution, etc.), printed on a
shaded background and marked additionally with a picto
gram. A distinction is made between the following danger
warnings:
Warning
This means that failure to observe this instruction may
result in serious personal injury or damage to property.
Caution
This means that failure to observe this instruction may
result in personal injury or damage to property.
Please note
This means that failure to observe this instruction may
result in damage to property.
The following pictogram marks passages in the text which
describe activities with electrostatically sensitive compo
nents.
Electrostatically sensitive components may be damaged if
they are not handled correctly.
Contents and general instructions
VIII Festo P.BE−SPC200−S7−PC−EN en 0609a
Marking special information
The following pictograms mark passages in the text contain
ing special information.
Pictograms
Information:
Recommendations, tips and references to other sources of
information.
Accessories:
Information on necessary or sensible accessories for the
Festo product.
Environment:
Information on environment−friendly use of Festo products.
Text markings
·The bullet indicates activities which may be carried out in
any order.
1. Figures denote activities which must be carried out in the
numerical order specified.
Hyphens indicate general activities.
Autres manuels pour SPC200 Series
14
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Festo Contrôleurs
Festo
Festo CMMP-AS M3 Series Manuel de la liste des pièces
Festo
Festo SEC-AC-305-CO Manuel utilisateur
Festo
Festo CHB-C-N Manuel de la liste des pièces
Festo
Festo VPPI S1BT Series Manuel utilisateur
Festo
Festo CECC-X-M1 series Manuel de la liste des pièces
Festo
Festo CMMP-AS-***-M0 Series Instructions d'utilisation et d'installation
Festo
Festo VEAB Manuel utilisateur
Festo
Festo DFPI-ND2P Series Guide de configuration
Festo
Festo LRP-1/4 Series Manuel utilisateur
Festo
Festo DFPD-Series Manuel utilisateur
Festo
Festo DFPD-x-RS Series Manuel utilisateur
Festo
Festo MPS PA Manuel utilisateur
Festo
Festo EPCO-16 Manuel utilisateur
Festo
Festo SPC200 Series Manuel utilisateur
Festo
Festo SEC-ST-48-6-P01 Manuel utilisateur
Festo
Festo SFC-LAC Series Guide de référence
Festo
Festo CMMO-ST-xxx-LKP series Manuel utilisateur
Festo
Festo CMXR-C2 Instructions d'utilisation et d'installation
Festo
Festo DAPS-2880-8000 R F Series Mode d'emploi
Festo
Festo CMXR-C2 Mode d’emploi
