Felt TA FRD Manuel utilisateur
1
CONTENTS:
2. BAYONET FORK INSTALLATION
4. AEROBAR INSTALLATION
5. RISER, PAD, & EXTENSION INSTALLATION
8. SEATPOST INSTALLATION
9. SEATPOST HEAD & SADDLE INSTALLATION
11. “TRAIN” CRANK INSTALLATION
13. “RACE” CRANK INSTALLATION
15. REAR WHEEL INSTALLATION
17. FRONT WHEEL INSTALLATION
18. COG & LOCKRING INSTALLATION
2
BAYONET FORK INSTALLATION
STEPS:
1. Place one (1) B3 headset bearing onto integrated fork crown race.
2. Insert fork steerer into frame.
3. Place one (1) B3 headset bearing into frame.
4. Twist B3 tension nut onto steerer.
5. Twist fork to ensure tension nut is not over tightened.
6. Using a torque wrench, tighten B3 headset set screw to 6-8 Nm
PARTS:
A. Frame
B. Fork
C. 2 x Bayonet 3 (“B3”) 19mm headset bearings
D. 1 x Bayonet 3 (“B3”) headset tension nut, 8mm
E. 1 x Bayonet 3 (“B3”) headset set screw, 5mm
REQUIRED TOOLS:
- 8mm Allen key
- 5mm Allen key
- Torque wrench
3
BAYONET FORK INSTALLATION
4
AEROBAR INSTALLATION
STEPS:
1. Use 4mm Allen key to loosen M5x18 socket head cap screw on stem.
2. Position Aerobar stem onto B3 tension nut, and align fork bolt to stem.
3. While applying light, downward pressure on the stem, use a torque wrench
with a 3/8” drive, long hex, 6mm socket bit to tighten fork bolt to 10-12 Nm.
PARTS:
A. Aerobar
B. Frame
REQUIRED TOOLS:
- 3/8” drive, long hex, 6mm socket bit
-4mm Allen key
-Torque wrench
5
RISER, PAD & EXTENSION INSTALLATION
STEPS:
The TA FRD armrests can be set up in three distinct congurations—Low, Mid or High—each utilizing
a unique selection of spacers to achieve the rider’s desired position. The Mid conguration can even
be set up in two different heights, depending on the specic spacer used (5mm or 10mm). Refer to the
diagrams on the following page for detailed views of the specic components required.
IMPORTANT: For all congurations, make sure to insert the anti-crush washers
into the extension brackets. Using a torque wrench, tighten bolts to 6-8 Nm.
PARTS:
A. Aerobar
B. 2 x Extensions
C. 2 x Extension brackets
D. 2 x Upper aero nut
E. Aero spacers (5, 10mm)
F. 4 x M5x12mm at head socket cap screw
G. 2 x Arm rest bracket
H. 2 x Arm rests
I. 2 x Arm rest pads
J. Anti-crush washers
K. 2 x M6x15mm socket cap screw
L. 4 x Extension bolts (40, 45, 50, 55mm) 6-8 Nm
M. Fit Washers
REQUIRED TOOLS:
- 4mm Allen key
- 5mm Allen key
- Torque wrench
6
RISER, PAD & EXTENSION INSTALLATION
40mm
45mm
55mm
6-8 Nm
6-8 Nm
6-8 Nm
7
RISER, PAD & EXTENSION INSTALLATION
8
SEATPOST INSTALLATION
STEPS:
1. Position wedge with taper facing towards the rear of the frame, and the end of the wedge with more material
above the bolt hole to the top.
2. Hold the wedge in place against the frame using your ngers.
3. Insert both M5x18 socket head cap screws through the frame and into the seatpost wedge.
4. Insert seat post into seat tube, sliding wedge into the bottom of the seatpost.
5. Using a 4mm Allen key, repeatedly alternate the tightening of the top and bottom screws to ensure
even pressure. Using a torque wrench, fully tighten both screws to 6 Nm.
PARTS:
A. Seatpost
B. TA FRD seatpost wedge
C. 2 x M5x18 socket head cap screw
REQUIRED TOOLS:
-4mm Allen key
-Torque wrench
9
SEATPOST HEAD & SADDLE INSTALLATION:
STEPS:
1. Place each Saddle Clamp Upper into a Saddle Clamp Adjustment Head Half, positioning them so the hooked
surfaces are adjacent and can grip a seatpost rail.
2. Place each Saddle Clamp Lower onto a Saddle Clamp Upper, aligning its holes with the oval-shaped holes of
the Saddle Clamp Uppers.
3. Place the bolt and nut threads-down into the holes of the two stacks of Saddle Clamp parts, aligning tooth on
nut to slot in Saddle Clamp Lower.
4. Turn each stack upside down so that the threads face away from your work surface. The chamfer of the
Adjustment Head Half will be placed in contact with the chamfered surface of the seatpost. Apply friction paste
between surfaces.
5. Place one stack thread-side down into the seatpost so the chamfer of the Adjustment Head Half is in contact
with the chamfer of seatpost alloy insert.
6. Holding the remaining stack of pieces in place on the other side of the seatpost, align the bolt threads with the
nut threads and tighten loosely.
7. Slide a saddle (not included) into the saddle clamp assembly beginning from the rear of the saddle.
8. Once your preferred saddle angle and fore/aft position are established, tighten the saddle clamp bolt to 10-12
Nm using a torque wrench.
PARTS:
A. 2 x Saddle Clamp Upper
B. 2 x Saddle Clamp Adjustment Head Half
C. 2 x Saddle Clamp Lower
D. Saddle Clamp Binder Nut
E. Saddle Clamp Binder Bolt
REQUIRED TOOLS:
-4mm Allen key
-Torque wrench
-Friction paste
10
SEATPOST HEAD & SADDLE INSTALLATION:
Table des matières
Autres manuels Felt Vélo
Felt
Felt FR SERIES Manuel utilisateur
Felt
Felt Bicycle Manuel utilisateur
Felt
Felt AR Manuel utilisateur
Felt
Felt Virtue Nine Manuel utilisateur
Felt
Felt VR SERIES Manuel utilisateur
Felt
Felt DOCTRINE Manuel utilisateur
Felt
Felt Edict Nine Instructions de montage
Felt
Felt IA Guide de configuration
Felt
Felt DECREE 1.5 Manuel utilisateur
Felt
Felt EDICT Manuel utilisateur
