Fellowes esi FlexCharge4C Manuel utilisateur
Assembly instructions
FlexCharge™4C
Model # FCH4C-WHT
Model # FCH4C-BLK
Personal desktop power
Page 2
FlexCharge4C Safety instructions/warnings
Please review these instructions before beginning the installation. Check that all parts and tools needed
were provided with your order (see illustration on following page). Contact your supplier if any parts are
missing. Do not discard the packaging until content that the product operates to your satisfaction.
Safety instructions/warnings
Always read the safety instructions carefully.
• Do not install near heat sources such as radiators, heat registers, stoves or
other equipment (including amplifiers) that produce heat.
• Unplug the unit during lightning storms or when unused for extended
periods of time.
• To reduce the risk of fire or electric shock, do not expose this unit to rain or
moisture, including any drips or splashes.
• Objects filled with liquids such as vases, should never be placed on or near
the unit.
• Do not open the unit due to risk of electric shock hazard.
• The outlet used to power the unit should be easily accessible and located
near the equipment.
• The unit is for indoor use only.
• Please refer to the marking label on the unit for input and output ratings. Do
not overload the power supply.
• DO NOT USE this unit in life support applications where failure of the
unit can reasonably be expected to cause the failure of the life support
equipment or to significantly aect its safety or eectiveness.
• DO NOT USE this unit in the presence of a flammable anesthetic mixture
with air, oxygen or nitrous oxide.
• Failure to adhere to these instructions eectively voids the warranty.
Page 3
FlexCharge4C Parts and tools
Parts provided
Additional tools required
• Phillips screwdriver
• Power drill with
1
/
8
" drill bit (under-desk mounts only)
There are three ways to mount the FlexCharge4C power module:
• Edge mount (page #4)
• Grommet mount (page #6)
• Under-desk mount (page #8)
Choose the best mounting method based on user preference and the mounting circumstances.
edge mount grommet mount under-desk mount
protected
indicator light
power outlets
USB-A charging port
bracket/clamp assembly (1)power module (1)
M3x12 panhead
screw (2)
M4 Allen key (1)
M4x14
screw (4)
Important : Hand-tighten screws only.
USB-C charging port
wood
Edge mount Grommet mount Under-desk mount
Page 4
Edge mount
With edge mounts, the product is clamped to the
edge of the worksurface.
Step #1: if necessary, raise clamp on bottom bracket
Skip this step if worksurface thickness is 0.9" or more.
• The clamp is attached to the lower two holes on bottom bracket. If worksurface thickness is less than
0.9", clamp attachment must be moved to the upper two holes.
• Use the M4 Allen key to unscrew the two
M5x8 socket cap screws that secure the
clamp.
• Raise the clamp to the upper two holes
and attach it using the socket cap screws.
Tighten securely using the Allen key.
Step #2: attach bracket/clamp assembly to power module
• Route the power cord through the opening in the
top bracket.
• Attach the top bracket to the rear of the power
module using the two M3x12 panhead screws.
Hand-tighten securely.
power module
clamp
bottom
bracket
top
bracket
M3x12
clamp
bottom
bracket
M5x8
s
ocket cap
screw
FlexCharge4C Edge mount
Page 5
Step #3: clamp FlexCharge4C assembly to worksurface
• Position the assembly in the desired location and clamp it securely
to the worksurface by tightening the triangle knob.
• Plug the power cord into an AC outlet.
You are now ready to use the two AC power outlets, one USB-A, and one USB-C charging
ports on the FlexCharge4C.
worksurface
triangle knob
FlexCharge4C Edge mount
Page 6
Grommet mount
The grommet mount method is similar to the
edge mount method, except here the assembly
is clamped to the edge of a grommet hole rather
than the edge of the worksurface. Minimum
diameter of the grommet hole is 2.3".
Step #1: remove clamp from bottom bracket
• Unscrew the two M5x8 socket cap screws using the M4 Allen key.
— Remove the clamp from the bottom bracket.
Step #2: attach M5x8 screws to bottom bracket
• Install the two M5x8 screws back onto the bottom bracket, leaving about 1/8" exposed between the
screw heads and the bracket.
— With worksurface thicknesses between
0.9" and 2", attach the screws to the lower
two holes.
— With worksurface thicknesses less than 0.9",
attach the screws to the upper two holes.
lower
uppe
r
0.9" to 2" 0.4" to 0.9"
1
/
8
"
clamp
bottom
bracket
M5x8
s
ocket cap
screw
FlexCharge4C Grommet mount
Page 7
Step #4: clamp power module assembly to worksurface
• Insert the bottom bracket through the grommet hole.
• Attach the clamp to the bottom bracket.
— Fit the keyhole openings in the clamp over the M5x8 screw heads. Tighten the screws securely over
the narrow portion of the keyholes using the M4 Allen key.
• Clamp the assembly securely to the worksurface by tightening the triangle knob.
• Plug the power cord into an AC outlet.
You are now ready to use the two AC power outlets, one USB-A, and one USB-C charging
ports on the FlexCharge4C.
Step #3: attach bracket assembly to power module
• Route the power cord through the opening in the top bracket.
• Attach the top bracket to the rear of the power module
using the two M3x12 panhead screws. Hand-tighten
securely.
power module
bottom
bracket
2"
top
bracket
M3x12
FlexCharge4C Grommet mount
hook keyholes onto
screws and tighten worksurface grommet
hole
Page 8
Under-desk mount
With this method, the top bracket is turned
upside-down so that it can be mounted to the
underside of the worksurface with M4x14 wood
screws. As with the other methods, the power
module is mounted to the bracket using two
M3x12 panhead screws.
Step #1: remove top bracket
• By removing the four #6-32x⁄ screws.
• Remove the top bracket from the bracket/clamp assembly.
#6-32x
¼
top
brac
ket
top
bracket
Step #2: mark and drill pilot holes
• Use the top bracket as a template to mark where to drill
four pilot holes.
— Position the bracket at the desired location, typically at
the front of the worksurface on the left or right side.
— Mark hole locations.
• Drill ½" deep pilot holes using a
1
/
8
" drill bit.
Caution: Be careful not to not drill through the top of the
worksurface.
FlexCharge4C Under-desk mount
Page 9
Step #3: attach top bracket to underside of worksurface
• Attach the bracket using the four M4x14 wood screws. Hand-tighten securely.
Step #4: attach power module to bracket
• Route the power cord through the opening in the top bracket.
• Attach the power module to the bracket using the two M3x12
panhead screws. Hand-tighten securely.
You are now ready to use the two AC power outlets, one USB-A, and one USB-C charging ports on the
FlexCharge4C.
M4x14
M3x12
FlexCharge4C Under-desk mount
Page 10
FlexCharge4C Additional features
Additional Features
• FlexCharge4C oers built-in surge protection with an indicator light. The light displays when surge
protection is active on your FlexCharge4C.
— If the light is not illuminated, please contact Customer Service.
• AC outlet orientation can be rotated to accommodate large plugs
• FlexCharge4C complies with UL 962A Standard for Furniture Power Distribution Units and meets
respective spill test criteria.
27W output max. USB-A and USB-C (PD3.0) charging modules can charge multiple devices at the same time.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Fellowes Alimentation
