Fanimation Palmetto Manuel utilisateur

The Palmetto

MODEL NOs: FP601 –5**

OWNER’S MANUAL

READ AND SAVE THESE INSTRUCTIONS

WARNING

DO NOT INSTALL OR USE FAN SYSTEM IF ANY PART IS DAMAGED OR MISSING. THIS

PRODUCT IS DESIGNED TO USE ONLY THOSE PARTS SUPPLIED DESIGNATED

SPECIFICALLY FOR USE BY FANIMATION. SUBSTITUTION OF PARTS OR ACCESSORIES

NOT DESIGNATED FOR USE BY FANIMATION COULD RESULT IN PERSONAL INJURY OR

PROPERTY DAMAGE. CONTACT FANIMATION FOR MISSING OR DAMAGED PARTS.

(888) 567-2055

OR

(317) 733-4113

MAINTENANCE AND BLADE CLEANING

PERIODIC CLEANING IS RECOMMENDED USING A SOFT BRUSH OR LINT FREE CLOTH.

ABRASIVE AND/OR NON-ABRASIVE CLEANING AGENTS ARE NOT REQUIRED AND

SHOULD BE AVOIDED TO PREVENT DAMAGE TO FINISH. ALSO LIGHT DUSTING OF THE

SELECTED BLADE IS RECOMMENDED. A FEATHER DUSTER WILL WORK BEST.

PERIODICALLY TIGHTEN SET SCREWS ON SHAFT ADAPTERS (P608MAC AND P610MAC),

BLADE HUBS TO SHAFT SCREWS AND HUB TO BLADE STEMS.

1. LOCATE POWER

a. POWER IS SUPPLIED BY PURCHASER/CONTRACTOR

b. DISCONNECT POWER SUPPLY AT BREAKER BOX.

c. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY

(P680M**)

d. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY

(P680M**)

e. A SINGLE PHASE ELECTRICAL FEED IS REQUIRED

f. MOTOR IS SINGLE SPEED ONLY

g. DO NOT OPERATE WITH ANY SPEED CONTROL

2. INSTALLATION NOTE

a. IT IS RECOMMENDED THAT EACH CEILING MOUNT ASSEMBLY (P680M**, P600S**, AND P600D** IF REQUIRED)

HAVE ¾” PLYWOOD BACKING SECURED TO A STRUCTURAL MEMBER FOR ADEQUATE SUPPORT.

3. MOUNT MOTOR ASSEMBLY OVER POWER SUPPLY TO COVER JUNCTION BOX.

a. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED

b. DRILL PILOT HOLES

c. START 2 SUPPLIED LAG BOLTS WITH WASHER IN THE OUTSIDE HOLES

d. DO NOT COMPLETELY TIGHTEN LAG BOLTS AT THIS TIME

e. CONNECT THE MOTOR WIRES TO THE SUPPLIED LEADS

i. BROWN TO “HOT”

ii. BLUE TO “NEUTRAL”

f. POSITION MOTOR ASSEMBLY OVER THE FINAL TWO PREDRILLED HOLES AND FASTEN WITH REMAINING LAG

BOLTS AND WASHERS

g. SECURE ALL FOUR LAG BOLTS

4. LOCATE POSITION OF EITHER END OR CENTER ASSEMBLY (P600S** OR P600D**)

a. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 9’11” CENTER OF BASE TO CENTER OF BASE OR

b. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 10’5” FROM OUTSIDE EDGE OF BASE TO OUTSIDE

EDGE OF BASE.

c. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED

d. DRILL PILOT HOLES

e. MOUNT NEXT ASSEMBLY IN DESIRED LOCATION AND TIGHTEN ALL FOUR LAG BOLTS SECURELY

f. MEASURE DISTANCE FROM INSIDE EDGE OF COUPLER ADAPTER TO INSIDE EDGE OF COUPLER ADAPTER TO

DETERMINE LENGTH OF ROTATING SHAFT (TUBE108**)

g. CUT ROTATING SHAFT (TUBE108**) TO MEASURED LENGTH.

h. ON SECOND ASSEMBLY LOOSEN THE TWO LAG BOLTS ON THE INSIDE EDGE OF THE BASE ENOUGH TO LEAN IT

BACK.

i. INSTALL DESIRED NUMBER OF HUB ASSEBMLIES (P606**) ON THE ROTATING SHAFT (TUBE108**)

j. SPACE HUBS (P606**) ALONG ROTATING SHAFT AS DESIRED AND SECURE WITH SET SCREWS

k. INSERT ROTATING SHAFT IN THE MOTOR END COUPLER AND TIGHTEN SET SCREW.

l. LEAN BACK SECOND ASSEMBLY AND INSERT ROTATING SHAFT (TUBE108**) INTO THE COUPLER ADAPTER.

m. TIGHEN LAG BOLTS SECURELY ON THE BASE

n. TIGHTEN SET SCREW ON COUPLER ADAPTER.

5. IF YOU ARE INSTALLING ADDITIONAL SECTIONS REPEAT STEP 4 FOR EACH

a. BE SURE THAT THE MIDDLE ASSEMBLIES ARE P600D** AND THE FINAL ASSEMBLY IS THE P600S**

6. INSERT BLADE ASSEMBLY STEM INTO HUB ASSEMBLIES AND SECURE WITH SETSCREWS.

a.

7. CHECK THAT HUBS, BLADE STEMS, BLADES AND ROTATING SHAFT (TUBE108**) SETSCREWS ARE SECURE

8. RESTORE POWER TO SYSTEM.

Ce manuel convient aux modèles suivants

4

Table des matières

Autres manuels Fanimation Ventilateur

Fanimation

Fanimation AMPED FP7634 Series Manuel utilisateur

Fanimation

Fanimation Subtle Manuel utilisateur

Fanimation

Fanimation FP8062 Series Manuel utilisateur

Fanimation

Fanimation The Stafford PL8274 Manuel utilisateur

Fanimation

Fanimation SCULPTAIRE FP8511 Series Manuel utilisateur

Fanimation

Fanimation Windpointe FP7500 Manuel utilisateur

Fanimation

Fanimation FP4820PW The Cumulos Manuel utilisateur

Fanimation

Fanimation Camview FP6225BL Manuel utilisateur

Fanimation

Fanimation Edgewood TF100 Series Manuel utilisateur

Fanimation

Fanimation SHOWROOM CELANO FP8062B Series Manuel utilisateur

Fanimation

Fanimation Torrento FP920 Series Manuel utilisateur

Fanimation

Fanimation BLITZ LP8377LBN Manuel utilisateur

Fanimation

Fanimation WRAP MAD8530 Manuel utilisateur

Fanimation

Fanimation Old Havana Series Manuel utilisateur

Fanimation

Fanimation KERRING FP3073 Series Manuel utilisateur

Fanimation

Fanimation Belleria FP4320 Series Manuel utilisateur

Fanimation

Fanimation PICKETT FP7996 Series Manuel utilisateur

Fanimation

Fanimation distinction A1 series Manuel utilisateur

Fanimation

Fanimation KWARTET FPS8553 Series Manuel utilisateur

Fanimation

Fanimation FP8012 series Manuel utilisateur

Fanimation

Fanimation Torrento FP920 Series Manuel utilisateur

Fanimation

Fanimation Air Shadow FP815FS Manuel utilisateur

Fanimation

Fanimation FP7988MB Manuel utilisateur

Fanimation

Fanimation Islander FP320 Series Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage