EZPull Trap Manuel utilisateur
E
EZ
ZP
Pu
ul
ll
l
T
Tr
ra
ap
p
S
Se
et
tu
up
p
&
&
P
Pa
ai
ir
ri
in
ng
g
G
Gu
ui
id
de
e
For TRBP-02 (HW 2.5.0)
EZPull Trap is a voice activated, wireless clay target release
system for Trap.
EZPull Trap has special Setup and Pairing modes intended only
for the Gun Club’s administrator.
Warning: Always stand clear of any traps that may be activated
by EZPull.
1. Using Setup Mode: The Setup mode provides access to
parameters that determine the operation of the device.
1.1. Enter Setup Mode: Remove the rubber boot. Remove
the battery door. Remove one battery. Press and hold
setup “wrench” [ ] key and replace the battery. When
both lights are on steady, release the key. The lights
will alternate slowly indicating the unit is in Setup mode.
1.2. Exit Setup Mode: When in Setup mode, press and hold
the “Target” [] and “Speaker” [ ] keys
simultaneously. Both lights will turn on steady. Release
the keys. Unit will go directly to release mode ready to
release targets on key press/Voice.
1.3. Access Setup Adjustment: pressing and holding any two
key combinations simultaneously, (except [] + [ ])
will result in both lights flashing rapidly. Keep holding
the keys until both lights are turned off. Then release
the keys. The setup parameter’s current numeric value
will be indicated by the LEDs.
1.4. Understanding the numbering indicators:
1.4.1. Each parameter can be set to numbers in the
range 1 to a maximum value specific to the
parameter but never more than 16.
1.4.2. The left LED indicates the “tens” digit.
1.4.3. The right LED blinks the number of times
corresponding to the “ones” digit
1.4.4. Examples:
Number 06: left light is off; right light blinks 6
times.
Number 14: left light is on; right light blinks 4
times.
1.5. Adjusting the Number:
1.5.1. Increase: for the next value, press and quickly
release the “Speaker” [ ] key. The operation is
cyclical, after you reach the maximum value, the
next number is #1.
1.5.2. Decrease: for the previous value, press and
quickly release the “Target” [] key. The
operation is cyclical, after you reach #1, the next
number is the maximum value.
1.5.3. Verify: After each key press, observe the lights
to verify the number.
1.6. Exit adjustment: Once you verify the correct value,
press the “ON/OFF” [ ] key to save and return to Setup
mode or press the “wrench” [ ] key to exit without
saving any changes.
E
EZ
ZP
Pu
ul
ll
l
T
Tr
ra
ap
p
S
Se
et
tu
up
p
&
&
P
Pa
ai
ir
ri
in
ng
g
G
Gu
ui
id
de
e
For TRBP-02 (HW 2.5.0)
2. Wireless Address Setup: The remote microphone units and
base station on each Trap field must be set on the same
unique address code. The address code is made of two
numbers:
Field: The Field number is a common radio address for all the
EZPull systems on the same area. If you have 16 Trap fields
or less you do not need to change this address.
Station: The station number is the unique radio address for
communicating between all units and base station on the
same trap field.
First set the same address on all the EZPull remote units on
the Trap field and then pair with a Base Station (See below).
2.1. Follow section 1 above to enter and work in Setup
mode.
2.2. Changing the Station Number: Use the [ ] + [ ]keys
combination access the Station Number adjustment.
EZPull can be set to any station number in the range 1
to 16.
2.3. Changing the Field Number: Use the [ ] + [ ] keys
combination to access the Field Number adjustment.
EZPull can be set to any Field number in the range 1 to
14.
3. Changing the Voice sensitivity: This parameter allows
adjustment of the sensitivity to voice. Higher numbers are
more sensitive. A typical value is in the range 3 to 4.
3.1. Follow section 1 above to enter and work in Setup
mode.
3.2. Use the [ ] + [ ] keys combination to access the voice
sensitivity adjustment. Voice Sensitivity values are
Typically:
3.2.1. For very high sensitivity, set to values 4 or 5.
The down side is the unit will also be sensitive to
noise and may throw targets on any speech
sound and some gunshot echoes.
3.2.2. For average sensitivity, set to 3. This will reduce
sensitivity to noise. This is the recommended
value for use with TargetManager.
3.2.3. Set to 1-2 in very noisy environment including
gunshots echoes from nearby fields. Shooter will
need to call loud and long “Pull”.
E
EZ
ZP
Pu
ul
ll
l
T
Tr
ra
ap
p
S
Se
et
tu
up
p
&
&
P
Pa
ai
ir
ri
in
ng
g
G
Gu
ui
id
de
e
For TRBP-02 (HW 2.5.0)
4. Paring the remote units with a Base Station: The remote
units communicate with a base station that controls the Trap
machine. There are two options for a base station:
EZPull Target Manager: uses a card payment system. The
Card unit is typically mounted at the entrance to the Trap
field. Refer to the Administrator’s Guide of the EZPull Target
Manager for specific setup instructions.
Trap base station: located at the back of the trap house and
directly controls the trap machine. The remote units and base
station on each trap field must be set on the same unique
address code.
Follow procedure below to pair the base station with the
Remote units:
4.1. Turn off all the remote units.
4.2. Disconnect the Base unit from the Trap or any high
voltage source.
Warning: working while high voltage source is
connected, can be hazardous and may result in serious
injury.
4.3. Set the Base Station in paring mode.
4.3.1. Place a small magnet next to the magnetic
switch (looks like a red bar) on the left side of
the base station.
4.4. The Red LED will blink for 2 seconds, then the Yellow
LED will blink rapidly and then both lights will glow
steady. Remove the magnet at once. Both Red and
Green/Yellow LEDs will flash indicating the base station
is waiting for a Pairing call from the remote.
4.5. Set one of the remote units in Paring Mode:
Remove the rubber boot. Remove the battery door.
Remove one battery.
Press and hold the On/Off key [ ] and replace the
battery. Both lights should be on steady. Release the
key. Observe the LED indicators on the base station and
release the key.
4.6. If Pairing is successful you will see the following light
flashing sequence: Blue, Red, Blue, Yellow followed by
slow flashing of the Yellow LED indicating normal
operation mode.
4.7. Following a successful pairing, the remote unit should
be in sleep mode (no lights). If lights are still flashing,
remove one battery, wait 10 seconds and replace it.
4.8. Verify pairing: Press and release the [] on the remote.
Observe the lights on the base station. Press and
release the “Target” [ ] key. The Blue light on the base
station should turn on momentarily.
Yellow
Blue
Red
Reed Switch
Autres manuels EZPull Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
