Extron electronics Cable Cubby 1202 Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

Cable Cubby 1202 and 1402 • Installation Guide

This guide provides instructions for an experienced technician to install and connect the

Extron Cable Cubby 1202 and 1402.

The Cable Cubby units are furniture-mounted enclosures for cable access,

connections, and AC power. Cables that are not in use can be stored out of the

way while remaining connected to the presentation system.

NOTE: This product is intended for use only with Extron UL listed

power modules (not included).

Planning

Check with local and state regulations before starting the installation

Ensure that the planned installation complies with national and local building and electrical codes.

Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check all parts and equipment before installation

Ensure that all parts are present in each kit.

Ensure that necessary tools and equipment are available for the installation.

Kit Contents

1 2

4 8

1 2

6 (3/8"), 2 (1/4") 12 (3/8"), 4 (1/4")

1 2

8 16

Cable Cubby 1202 Cable Cubby 1402

#4-40 Module Screws

#6 Pan-head Mounting

Screws and Star Washers

AAP Frame Plate

Cable Grommet Plate

Hole Plugs

Retractor Pin & Clip

Connectivity

Bracket

#4-40 Module Screws

AAP Frame Plate

Cable Grommet

Plate

Hole Plugs

Retractor

Bracket

Retractor

Pin & Clip

#6-32 Mounting

Screws and Star

Washers

Cable Cubby 1202 and 1402 • Installation Guide (Continued)

Preparing the Table

Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.

Determine the best location for the enclosure

Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.

Ensure that the edge on which the lid opens is oriented correctly.

Ensure that there is ample space under the table for cables. Allow at least 36 inches of cable loop for each cable (see

Routing and Connecting Cables on page 8).

When installing Retractors in the Cable Cubby, ensure that there is enough space for the Retractor assembly under the table

or furniture (see the Retractor dimensions in the images below or go to www.extron.com).

Retractor dimensions

NOTE: Shown with Cable Cubby 1202 enclosure

Retractor Series:

8.0"

(203 mm)

23.3"

(592 mm)

9.0"

(229 mm)

18.2"

(462 mm)

14.5"

(368 mm)

21.7"

(551 mm)

Horizontal Mounting Vertical Mounting Angular Mounting

Retractor Series XL:

29.4"

(747 mm)

26.9"

(683 mm)

24.2"

(615 mm)

20.5"

(521 mm)

9.0"

(229 mm)

11.5"

(292 mm)

Preparing the Cable Cubby

Step 1 — Assemble Connectivity Modules

Connectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAPs, cable pass-through, or

Retractors. Follow the steps below to assemble the connectivity modules of your choice.

Option 1: AAP Module

Secure the AAP plate

on the connectivity brackets

using four of the provided

module screws.

Insert cables through the bottom

of the connectivity bracket.

Connect cables to the AAPs.

Secure up to three single space

AAPs in the AAP panel.

#4-40 Nut with

Captive Washer

NOTE: After assembling the module, proceed to Step 2 — Install the Modules on page 5.

Choose a method for cutting the hole in the table

CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.

ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut

conduire à une blessure à l’oeil.

ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise

care to prevent scarring or damaging the furniture.

ATTENTION :L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et

qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

Choose one of the following methods for cutting the hole:

Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router

If using a CNC wood router or other

precise machinery, use the exact

cut-out dimensions for your model

(see the table below).

Visit www.extron.com for Cable Cubby routing

template part numbers and instructions.

Dimensions and cut-out templates are

available online at www.extron.com.

Product

Cut-out Dimensions

User Access

Width

Side

Dimension

CC 1202 10.00"

(254.0 mm)

4.00"

(101.6 mm)

CC 1402 10.00"

(254.0 mm)

6.75"

(171.5 mm)

Cut-Out Template for the Extron

Cable Cubby 1202

Outer Edge of Front Bezel

(Do not cut this line.)

1. Conﬁrm the product to be installed.

2. Removethe surface cut-out area

(gray) fromthe template.

3. Measure the cutout andtemplate.

4. Markthe position on the

furniturewhere the Cable Cubby 1200

will be installed.

5. Double check the dimensions and position,

then cut the opening.

Trim Ring

Lip

Cut-OutRadius:

0.25"(0.6cm)

User Access

P/N68-2472-01 Rev. A

Page Size: 11" x 17"

Print Scale 1:1

Do not Shrink

Cable Cubby 1202 and 1402 • Installation Guide (Continued)

Option 2: Cable Pass-Through Module

Option 3: Retractor Bracket

Use the Retractor Bracket to mount Retractors in the Cable Cubby enclosure. There are two options for installing the bracket

(Options 3a and 3b, below).

NOTE: If installing more than one bracket in the Cable Cubby 1402, see Retractor Configuration for

Cable Cubby 1402on page 7.

NOTE: After assembling the module, proceed to Step 2 — Install the Modules on the next page.

NOTES:

• After installing the bracket, proceed to Step 2 — Install the Modules on the next page to install the power module.

• After mounting the Cable Cubby on the table, install the Retractors (see Installing Retractors on page 7).

Option 3a

Use this option for the Cable Cubby 1202, and for vertical

or angular Retractor mounting in a Cable Cubby 1402.

Option 3b

Use this option for horizontal Retractor mounting in a

Cable Cubby 1402 only.

Secure the grommet plate on

the connectivity bracket

using four of the provided

module screws.

Insert cables through

the bottom of the connectivity

bracket and into the holes of

the grommet plate. Snap the included

hole plugs into any

unused holes.

Insert the bracket as shown.

The bracket may be

installed on the left or right

side of the enclosure and

must be installed at the lowest

height.

Secure the bracket using four

of the provided pan-head

mounting screws with star

washers. Tighten the screws

using a screwdriver.

Insert the bracket as shown.

The bracket may be

installed on the left or right

side of the enclosure and must

be installed at the lowest height.

Secure the bracket using four of

the provided pan-head mounting

scr

ews with star washers. Tighten

the screws using a screwdriver.

Cable Cubby 1202 and 1402 • Installation Guide (Continued)

Step 2 — Install the Modules

Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed

on the left or right side of the enclosure and at various heights.

NOTES:

• Ensure that there is enough room above the modules for the Cable Cubby lid to close completely.

• Use a screwdriver to secure the modules with the screws.

Insert the modules

into the Cable Cubby.

Secure the modules using four of the

provided pan-head mounting screws

and star washers.

125V~ 50-60Hz 12A MAX TOTAL

TOP

Cable Cubby 1202

WARNING: Risk of Electric Shock. To ensure proper electrical grounding, use the provided #6-32 mounting screws with the

star washers.

AVERTISSEMENT : Risque de choc électrique. Afin d’assurer une mise à la terre correcte, utilisez les fixations de mise à la

terre #6-32 et les rondelles en étoile fournies.

Cable Cubby 1202 and 1402 • Installation Guide (Continued)

Step 2 — Under the table, adjust the side clamps on the enclosure

NOTE: To lower the side

clamp, turn the lever down,

then press and hold the

locking plate while sliding

down the clamp.

Locking

Plate

Rotate the side clamp

outward and ensure that

the lever is down.

Slide the clamp all the

way up against the bottom

of the table.

Ensure the Cable Cubby

is rmly seated in the table.

Raise the lever to secure

the Cable Cubby.

Lever

21 3

Mounting the Cable Cubby in the Table

Step 1 — Mount the Cable Cubby ﬂush with the table

CAUTION: The anged edges of the top of the

surface enclosure are sharp. These edges are

also soft and may be easily nicked or bent.

Exercise caution when handling the enclosure

to prevent personal injury or damage to the

enclosure.

ATTENTION : Les extrémités à brides du haut

de la surface du boîtier sont aiguisées. Ces

extrémités sont aussi lisses et peuvent

facilement être coupées ou pliées. Soyez

prudents lorsque vous manipulez le boîtier an

d’éviter de l’endommager ou de vous blesser.

Remove the plastic

strips and lm on the

surface of the

Cable Cubby.

Ensure that the

side clamps are

seated against the

enclosure.

Lower the Cable Cubby

into the hole to test the

t. If necessary, car

efully

enlarge the opening.

n th

t t

nto



t. I

Vertical or angular mounting

The included brackets must be installed diagonally in the enclosures as shown below.

Cable Cubby 1402

Side View

Angular

Mounting

Vertical

Mounting

Retractor Conﬁguration for Cable Cubby 1402

Horizontal mounting

Install the brackets as shown below.

NOTE: Retractors may also be mounted using the Quad Bracket (see www.extron.com for part numbers).

Cable Cubby 1402

Side View

Horizontal Mounting

Installing Retractors

Follow the steps below to install Retractors. For horizontal or angular Retractor

mounting, see the information at

right, then follow the steps below.

Insert the pin through the

Retractor mounting hole on

the side of the Cable Cubby

and Retractor assembly.

Secure the clip

on the pin.

Insert Retractors into

the Retractor bracket. Secure the locking screw

on each Retractor. Do not

overtighten.

Clip

Angular Mounting

Remove the enclosure screws as shown above, then

follow this step:

Horizontal Mounting

See the Cable Retractor Series/2 Setup Guide, available

on the Extron website, for additional steps.

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

Top View

68-3552-01 Rev. A

05 20

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Installation Checklist

Planning (page 1)

Check with local and state regulations before starting the installation.

Check all parts and equipment before installation.

Preparing the Table (page 2)

Determine the best location for the enclosure.

Choose a method for cutting the hole in the table.

Preparing the Cable Cubby (page 3-5)

Assemble connectivity modules (page 3).

Install the modules (page 5).

Mounting the Cable Cubby in the Table (page 5)

Mount the Cable Cubby ﬂush with the table.

Adjust the side clamps under the table.

Installing Retractors (page 7)

Routing and Connecting Cables (page 8)

Routing and Connecting Cables

CAUTION:

Risk of Electric Shock.

This equipment must be grounded.

ATTENTION :

Risque de choc électrique.

Cet équipement doit être xé au sol.

NOTE: Ensure that there is no tension on the power

cable.

Connect cables to the AV system

and connect the AC power cord.

Using zip ties, secure cables to the holes

on the bottom of the Cable Cubby.

For cable pass-through applications,

allow at least 36 inches (0.9 m) of cable

loop for each cable.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Décodeur

Extron electronics

Extron electronics HDMI 101 Plus Manuel utilisateur

Extron electronics

Extron electronics TP R AV Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 200 Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 500 Manuel utilisateur

Extron electronics

Extron electronics Dual Length DVI Cable Equalizer DVI DL 101 Manuel utilisateur

Extron electronics

Extron electronics Retractor SM Manuel utilisateur

Extron electronics

Extron electronics Cable Cubby 1202 Manuel utilisateur

Manuels Décodeur populaires d'autres marques

FBS

FBS C01 Manuel utilisateur

peerless-AV

peerless-AV IBA2 Mode d’emploi

peerless-AV

peerless-AV IBA3AC Mode d’emploi

Channel Vision

Channel Vision AFFINITY P-0328 Manuel utilisateur

Minebea Intec

Minebea Intec IE11357 Manuel utilisateur

StarTech.com

StarTech.com BOX4CABLE Manuel utilisateur

Commercial Electric

Commercial Electric 5053-WH Manuel utilisateur

Motorola

Motorola DCT6412 DUAL-TUNER DVR AND HD SET-TOP - MICROSOFT... Instructions de montage

Renkforce

Renkforce 1395556 Manuel utilisateur

Huawei

Huawei FAT9102SD-32G Manuel utilisateur

VISSEM Electronics

VISSEM Electronics Opticube VSOF-OTB-E Manuel utilisateur

Beta

Beta 1844 15-H05/SCK Manuel utilisateur

FSR

FSR FL-1550 Manuel utilisateur

Renkforce

Renkforce 1674559 Manuel utilisateur

Minebea Intec

Minebea Intec PR 6130/64Sa Manuel utilisateur

KS Tools

KS Tools efuturo Wallbox Manuel utilisateur

Chatsworth Products

Chatsworth Products Evolution Manuel utilisateur

Minebea Intec

Minebea Intec Weighbridge PR 6021/68S Manuel utilisateur