Extron electronics NetPA Ultra Series Manuel utilisateur

NetPA Ultra Series • Setup Guide

The NetPA Ultra Series is a series of DSP and Dante®-enabled audio power ampliﬁers for use in a low-impedance speaker systems or

high-impedance line distribution audio systems.

NetPA U 1002 models deliver two channels of 100 watts, and is available in the following conﬁgurations:

• NetPA U 1002 (8 Ω/4 Ω) • NetPA U 1002-70V (70 V) • NetPA U 1002-100V (100 V)

NetPA U 1004 models deliver four channels of 100 watts, and is available in the following conﬁgurations:

• NetPA U 1004 (8 Ω/4 Ω) • NetPA U 1004-70V (70 V) • NetPA U 1004-100V (100 V)

The NetPA Ultra Series ampliﬁers all feature a compact 1U, 1/2-rack enclosure. The ampliﬁers have mounting holes for 9” and deeper

rack shelves, and are plenum rated with an optional ﬂex conduit adaptor. The units are convection cooled.

This guide provides instructions for an experienced installer to set up and operate these power ampliﬁers. The setup guide features the

NetPA U 1004, but the other ampliﬁers are installed in the same manner. For full installation, conﬁguration, and operation details, see

the NetPA U 1004 Series User Guide available at www.extron.com.

Installation Steps

Step 1 — Mounting onto a Rack

Turn off all of the equipment and disconnect it from the power source. Mount the ampliﬁer as required. They can be securely mounted

in a variety of locations, using optional Extron Mounting Brackets and accessories (see the Extron website for compatible optional

mounting accessories) or using the included 3-piece bracket system. The brackets do not come attached to the ampliﬁer.

The following sections describe two methods of rack mounting the ampliers.

Rack Ear Mounting (Single Unit)

All of the ampliﬁers ship with a set of rack ears, so these half rack-width ampliﬁers can be installed in a full rack-width space. Mount the

ampliﬁer with rack ears as follows:

1. If the amplifier has its rubber feet installed, remove them.

2. Attach the rack brackets (one long and one short) to the sides with the four provided #6 machine screws (1).

3. Insert the amplifier into the rack and align the holes in the rack ears with the holes on the rack.

4. Secure the amplifier to the rack using the four provided 10-32 x 3/4” screws (2).

NetPAU 1004 SB

12 3 4

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

NetP

POWERAMPLIFIERS

NetP

POWERAMPLIFIERS

NetP

NetPA U 1004 SERIES

1 2 3 4

OVER

TEMPLIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

NetP

Figure 1. NetPA U 1004 Rack Ear Mounting

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

The NetPA Ultra Series ampliﬁers all ship with a bridge plate connector to connect two ampliﬁers together and form full rack-width unit.

Mount and connect two ampliﬁers as follows:

1. If the amplifier has its rubber feet installed, remove them.

2. Position two amplifiers upside down and next to each other as shown below.

3. Use the bridge plate connector and the four provided #4 machine screws to connect the two units together (1).

4. Attach the two short rack ears to the units with the four provided #6 machine screws (2).

5. Insert the amplifier into the rack and align the holes in the rack ears with the holes on the rack.

6. Secure the amplifier to the rack using the four provided 10-32 x 3/4” screws (3).

NetPA U 1004 SERIES

1 2 3 4

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

NetPA U 1004 SERIES

1 2 3 4

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

Net

NetPA U 1002 SERIES

OVER

TEMP LIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

NetPAU 1004 SERIES

1 2 3 4

OVER

TEMPLIMITER/PROTECT

SIGNAL

POWERAMPLIFIERS

NetPA U

LTRA

NetPA U

LTRA

Mounting

screws (4)

Figure 2. NetPA U 1004 Bridge Plate Rack Mounting

Ventilation Recommendation

Excessive heat decreases the optimal lifetime of the power amplier. An

Over Temp LED indicator on the front panel of the amplier lights red

when the recommended operating temperature has been exceeded.

The NetPA Ultra ampliﬁers need to be arranged in a rack environment, so

that the environment around the ampliﬁer around does not reach or exceed

+122 °F (+50 °C). No more than four ampliﬁers should be stacked one-

on-top-of-the-other without an open rack space in between as seen in the

image to the right.

The NetPA Ultra ampliﬁers can also be arranged above or below a non-

NetPA Ultra device.

Step 2 — Captive Screw Audio Cable Wiring

Wire the captive screw connectors to the input or output as shown in the following ﬁgures.

Tip

leeve

Ring Tip

Sleeve

Jumper

Balanced Input Unbalanced Input

Figure 3. Input Wiring

Tip

leeve

Ring Tip

Sleeve

Balanced Output Unbalanced Output

Do not tin

the wires!

Figure 4. Output Wiring

NOTE:

• Balanced or unbalanced stereo sources can be connected with 6-pole connectors.

• When using the 5-pole CSR 6 captive screw to RCA adapter, connect it so the far left plug is inserted into the far left jack

of the 6-pole input.

Vent Space

NetPA Ultra Series • Setup Guide (Continued)

ATTENTION:

• For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative

(-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts

négatifs (–).

Step 3 — Remote Ports

STANDBY

REMOTE

Do not tin

the wires!

STANDBY

Tx Rx G

RS-232

Figure 5. Remote Volume Control and Standby Ports

• Standby mode is forced when the Standby pin is connected to the second G pin. The power LED on the front panel lights amber

when the amplifier is in Standby mode indicating that the amplifier is still receiving power despite the fact that it has turned off all

the outputs.

NOTE: The enabling and disabling of the auto-standby timer is handled through SIS or DSP Configurator. For more

details, consult the NetPA Ultra Series User Guide.

• Connect a 3.5 mm 3-pole captive screw connector to remotely control the volume via SIS commands, and connect a 3.5

mm, 2-pole captive screw to place the amplifier into Standby mode.

Protocol for the RS-232 port:

• 38,400 baud • 1 stop bit • 8 data bits • no parity

Step 4 — Speaker Wiring

Connect a four 4-pin, 5 mm captive screw connector for two channels of speaker output on the NetPA U 1002 group of amplifiers

and up to four channels on the NetPA U 1004 group of amplifiers. Each port has a screw flange to secure the plug to the

connector. Figure 6 shows how to wire the captive screw connector.

+BR—

100V OUTPUTS

CLASS 2

WIRING

Figure 6 Speaker Output Port and Wiring Diagram

ATTENTION:

• Do not tie channel output pins to each other or to ground. Doing so will short out the outputs, damage the amplifier,

or both.

• Ne pas lier les sorties 1 et 2 des canaux entre elles ou à la terre. Les sorties pourraient être court-circuitées et/ou

l’amplificateur pourrait être endommagé.

• To avoid risk of damage to the amplifier or the speakers, always connect low-impedance speaker loads (8 Ω/4 Ω)

and high-impedance speaker loads (70 V) to the appropriately marked output connectors on the amplifier.

• Pour éviter tout risque de détérioration de l’amplificateur ou des enceintes, connectez toujours les charges de

l’enceinte faible impédance (8 Ω/4 Ω) et les charges de l’enceinte haute impédance (70 V) aux connecteurs de sortie

correctement identifiés sur l’amplificateur.

NOTE: You must use Class 2 wiring for this output to comply with UL requirements.

NetPA Ultra Series • Setup Guide (Continued)

Step 5 — AT Port

Connect a RJ-45 connector to the AT port to connect and

12345678

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

A cable that is wired as TIA/EIA T568A at one

end and T568B at the other (Tx and Rx pairs

reversed) is a "crossover" cable.

T568B T568A

Crossover Cable

(for direct connection to a PC)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-green

2 orange 2 green

3 white-green 3 white-orange

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 orange

7 white-brown 7 white-brown

8 brown 8 brown

communicate with the Dante network. It is also one of the interfaces

DSP Congurator uses to communicate with the amplier. The

Link LED indicates when a connection is made.

Go to Conﬁgure Dante Device Settings on page 5 for information on

Dante settings. See the image to the right for wiring.

Step 6 — Powering on Ampliﬁer and

Adjustments

Reconnect all the power cables and switch on the rest of the

equipment before powering on the power amplier. The amplier will

boot-up for up to 10 seconds as the front panel LED lights amber.

Once the boot-up sequence is complete, the ampliﬁer takes more time to

sync with the Dante network, and begin the playback of streamed content.

Once playback begins, the front panel LED lights green.

ATTENTION:

• The amplifier must be powered on last.

• L’amplificateur doit être mis sous tension en dernier.

Step 7 — Checking LEDs

Check the Limiter/Protect and Signal LEDs on the front and rear panels to see if any problems are encountered (see “Front Panel

Features and Troubleshooting” in the NetPA Ultra Series User Guide for more information).

Step 8 — DSP Conﬁgurator Software Installation

There are no hardware controls for any of the units in the NetPA Ultra Series. Conﬁguration and control is done using either Extron DSP

Conﬁgurator software or SIS commands. To learn about full computer requirements, see the DSP Conﬁgurator product page on www.

extron.com.

Download DSP Conﬁgurator from the Extron Website

1. From the Extron home page (www.extron.com), click the Download tab to open the Download page.

2. Under Software (located on the left side of the page), select DSP Configurator Software. The DSP Configurator Software

product page opens.

3. Click the Download button and follow the on-screen instructions.

NOTE: An Extron Insider account is required to download DSP Configurator.

Step 9 — NetPA Ultra Series Conﬁguration

When power is connected to any unit of the NetPA Ultra Series and the rest of the audio system, audio output can be easily

congured to any listening environment via the DSP Congurator. The following steps details how to congure a NetPA Ultra

Series amplifier and uses the NetPA U 1004 as an example. However, all of the amplifiers are configured in the same way.

Downloading and Installing Dante Controller

1. From www.extron.com, hover over the Download tab at the top of the page.

2. From the Featured Software list, select Dante Controller. The Dante Controller product page opens.

3. Click the blue Download button.

4. Select Run to run the Dante Controller installer. Select Save to save the install file to run at a later time.

5. If you choose to run the file, follow all prompts. If you saved the file, click the saved file to begin installation when ready.

NOTE: The installed Dante Controller program files are saved in:

C:\Program Files (x86)\Audinate\Dante Controller\DanteController.exe.

NetPA Ultra Series • Setup Guide (Continued)

Conﬁgure a NetPA Ultra Series Ampliﬁer

1. Ensure the control computer is connected to either the AT port, RS-232 port or the rear panel USB configuration port.

2. Start the DSP Configurator software. From the splash screen drop-down menu, select the NetPA Ultra Series unit corresponding

to the unit connected to the control computer. Click OK. The main workspace opens.

3. The software starts in Emulate mode:

a. To create a configuration file offline and then upload that configuration to a NetPA Ultra Series unit at a later time, remain in

Emulate mode and save the configuration file.

b. To upload a configuration to the NetPA Ultra Series unit or download the current configuration from a unit, enter Live mode.

When in Live mode, changes made in DSP Configurator immediately affect the connected NetPA Ultra Series unit. To enter

Live mode, click Live at the top of the DSP Configurator workspace, or select Tools >Connect to Device, or press

<F6> on the keyboard.

NOTE: When Live mode is selected, a connection dialog box appears. Select the desired connection type and follow the

on-screen prompts (see the NetPA Ultra Series User Guide for more information on connecting live to a device).

The main workspace provides access to mix matrices, gain blocks, and

DSP processors for configuring a NetPA Ultra Series unit. It also provides

a menu bar across the top with additional configuration tools. For more

information on using the DSP Configurator, see the “DSP Configurator”

section of the NetPA Ultra Series User Guide, or the DSP Configurator

Help File that can be accessed by selecting Help >Contents or

pressing <F1>. Most dialog boxes within DSP Configurator contain a

Help button ( ) in the top right corner. Click this button to open the

help file topic for that particular dialog box.

Conﬁgure Dante Device Settings

Dante settings in the NetPA Ultra Series can be configured from DSP

Configurator. The device can be named in the Dante Device Settings,

which assists with indentifying a specific device in the Dante Controller software when there are multiple entries on the audio network.

ATTENTION: It is crucial that a Dante device be named before audio subscriptions with other devices are established. Existing

subscriptions are removed when a unit is renamed.

To configure Dante device settings:

1. Open DSP Configurator and connect live to the NetPA Ultra Series.

2. Select Tools >Device Settings. The Device Settings dialog box opens.

3. From the tabs at the top of the Device Settings dialog box, select Dante Device.

4. In the Device Name field, give the NetPA Ultra Series unit a name (recommended to be device model and location) so that it can

be easily identified in Dante Controller. No spaces are allowed in the name.

5. Dante device network settings can also be configured in this dialog box. Use the radio buttons and text fields to choose DHCP

(recommended) or Static IP and enter a static IP address configuration.

6. Click Apply.

7. Click OK to confirm changes and close the Device Settings dialog box.

Renaming the NetPA Ultra Series Amplifier in Dante Controller

1. From the control computer Start menu select: All Programs > Audinate > Dante Controller > Dante Controller

2. The Dante Controller -Network View screen opens. All Dante devices on the network are discovered and listed.

3. From the Device menu, select Device View or press <Ctrl+D> on the keyboard.

4. The Dante Controller -Device View dialog opens. Select the device being configured from the (Select aDante

Device...) drop-down list. The Device View dialog populates with the selected NetPA Ultra Series information.

NetPA Ultra Series • Setup Guide (Continued)

Figure 7 Populated Device View Dialog Box

5. Click the Device Config tab to open the Device Config page.

6. In the Rename Device panel, enter the new name of the device in the text field.

NOTE: No spaces are allowed in the name and names should be significant identifiers.

For example, NetPAUAmplifier-MainRack

7. Click Apply. A confirmation prompt opens. Click Yes to confirm the new name.

8. Repeat as necessary for all devices.

Creating a Physical Dante Network

A physical network is required to share Dante audio channels among Dante-enabled devices like those found in the NetPA Ultra

Series. Other devices capable of sending and receiving audio over a Dante network must be on the same physical network in

order to communicate with Dante. (see figure 8 for an example of a Dante network.)

AUDIO

Extron

muteselectmuteselect

NetPA U 1002 SERIES

LIMITER/PROTECT

SIGNAL

OVER

TEMP 21

INPUTS

ACTIVITY

CONFIG EXP LAN

XMP 240 C AT

EXPANSIONMATRIX PROCESSOR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CLIP

SIGNAL

Extron

XMP 240 C AT

Expansion Matrix Processor

Extron

NetPA U 1002-70V

Power Amplier

Extron

SF 26CT

Two-Way Ceiling Speakers

Extron

SF 26CT

Two-Way Ceiling Speakers

Extron

WPD 101 3.5 mm

Audio Pass-Through Wallplate

- Decorator-Style

Audio Line OutAudio Inputs

Wireless Mic 1

Wireless Mic 2

Ethernet

Assistive Listening

System Transmitter

Local Audio

Ceiling

Array Mic

Ethernet

Figure 8 Physical Dante Network Diagram

NetPA Ultra Series • Setup Guide (Continued)

Dante Network Setup

Use a standard Ethernet cable to connect a NetPA Ultra Series ampliﬁer to a Dante network via the AT port. Launch the Dante

Controller program.

Dante Controller automatically discovers all Dante devices on the network and allows other Dante-enabled devices to communicate

with it. The default device name is the model name followed by the last six characters of the device MAC address (for example, NetPA-

U-xxxxxx). Multiple devices on the same network can present difﬁculty in identifying inputs and outputs. To avoid confusion, rename

each device to a unique identiﬁer.

NOTE: To simplify setup, connect only one Dante device to the network at a time.

Finding a Dante Device IP Address

1. Open Dante Controller.

2. On the Dante Controller-Network View screen, click the Device Info tab.

3. On the Device Info page, locate the name of the NetPA Ultra Series in the Device Name column. The IP address is located in

the Primary Address column. In the example below, the IP address for the connected NetPA Ultra Series is 192.168.254.254.

Figure 6. Device Info Page

Dante Controller Operation

Dante Transmitters and Receivers

A Dante network is comprised of transmitters that output digital audio onto the Dante network and receivers that receive

digital audio input from the Dante network.

• Transmitters output digital audio from the device onto the audio network.

• Receivers take in digital audio from the audio network into the device.

NetPA Ultra Series Transmitters and Receivers

In the NetPA U 1004, the line output signals are parallel to their respective Dante output signal. The signal being sent out

of a line output is the same signal being sent out of its respective Dante output. In the NetPA U 1002, the line outputs are

independent of Dante outputs.

The NetPA Ultra Series AT input channels are Dante receivers because they receive digital audio signal from the Dante

network that can then be routed and mixed into a mix matrix. The NetPA U 1004 has four Dante inputs, while the NetPA U

1002 has two Dante inputs.

Finding a Dante

Device IP

Address

Dante

Controller

Operation

NetPA Ultra Series • Setup Guide (Continued)

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876

Network View Layout

In the Dante Controller software, Dante transmitters

are listed horizontally across the top of the Network

View (1), while Dante receivers are listed vertically on

the left side of the window (2). Creating a link in the

connection matrix routes audio from a transmitter to a

receiver (3).

Routing Devices

1. To show the transmitters of a Dante device, click

the +box next to the desired device in the Dante

Transmitters panel, such as NetPA-U-9175f2 (1).

The +changes to a –sign when the details for

the device expand.

2. To show the receivers of a Dante device, click

the + box next to the desired device in the

Dante Receivers panel, such as a

NetPA-U-MainRack (2).

3. Click the intersection of the desired subscription

(discrete connection) between a transmitter and a

receiver (3). A check mark at the intersection

indicates the subscription is made. A check mark

also appears next to the receiver channel.

NOTE: A receiver can subscribe to only one

transmitter. A transmitter can connect to multiple

receivers.

4. To undo routing, click the junction again to disconnect the receiver from the transmitter.

NOTE: After making changes to Dante network routing such as subscriptions, device names, or channel labels, wait at

least 5 seconds before disconnecting or powering down the devices. This ensures that the new information is properly

saved to those devices. Device level configuration such as sample rates, latency, and clock settings are saved instantly.

For more information on conguring a NetPA Ultra Series unit in Dante Controller, see the “Dante Controller” section of the

NetPA Ultra Series User Guide found on www.extron.com.

68-3165-50 Rev. A

07 20

Autres manuels pour NetPA Ultra Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Amplificateur

Extron electronics

Extron electronics XPA Ultra Series Manuel utilisateur

Extron electronics

Extron electronics VersaTools MDA 5A RCA Manuel utilisateur

Extron electronics

Extron electronics MP 101 Manuel utilisateur

Extron electronics

Extron electronics MPA 401-70V Manuel utilisateur

Extron electronics

Extron electronics XPA Ultra Fx Series Manuel utilisateur

Extron electronics

Extron electronics XPA 1002 Manuel utilisateur

Extron electronics

Extron electronics PA 300 Manuel utilisateur

Extron electronics

Extron electronics Fiber Optics Fox 4G DA8 Manuel utilisateur

Extron electronics

Extron electronics PA 300 Manuel utilisateur

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA12 Series Manuel utilisateur

Extron electronics

Extron electronics MP 101 D Manuel utilisateur

Extron electronics

Extron electronics MPA 152 MD Manuel utilisateur

Extron electronics

Extron electronics DTP HD DA8 4K 330 Manuel utilisateur

Extron electronics

Extron electronics XTRA Series Manuel utilisateur

Extron electronics

Extron electronics P/2 DA2 Plus Manuel utilisateur

Extron electronics

Extron electronics MDA 5SVA RCA Manuel utilisateur

Extron electronics

Extron electronics P/2 DA2xi MT Manuel utilisateur

Extron electronics

Extron electronics DA2 HD 4K PLUS Manuel utilisateur

Extron electronics

Extron electronics MDA 5V Manuel utilisateur

Extron electronics

Extron electronics MDA 3A Manuel utilisateur

Extron electronics

Extron electronics P/2 DA 2 WM/EC Manuel utilisateur

Extron electronics

Extron electronics CVDA 6 MX Dual Manuel utilisateur

Extron electronics

Extron electronics NetPA Ultra Series Manuel utilisateur

Extron electronics

Extron electronics VGA Distribution Amplifiers P/2 DA8 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur