Extron electronics WPD 110 A Manuel utilisateur

WPD Series Wallplates • Installation Guide

The Extron WPD Series (WPD 110 A, WPD 120 A, WPD 130 A, and WPS 140A) are single gang

pass-through wallplates with HDMI, DisplayPort, DVI, or VGA connectors and pigtail mounted

rear connectors. All models can be installed in single gang junction boxes, and include a

decorator-style frame. The models are as follows:

• WPD 110 A — HDMI, stereo audio, and control

• HDMI female to HDMI female connector on a pigtail

• 3.5 mm stereo audio jack with 3-pole captive screw connector

• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)

• WPD 120 A — DisplayPort, stereo audio, and control

• DisplayPort female to DisplayPort female connector on a pigtail

• 3.5 mm stereo audio jack with 3-pole captive screw connector

• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)

• WPD 130 A — DVI, stereo audio, and control

• DVI-I female to DVI-I female connector on a pigtail

• 3.5 mm stereo audio jack with 3-pole captive screw connector

• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)

• WPD 140 A — VGA, stereo audio, and control

• 15-pin VGA female connector on a pigtail

• 3.5 mm stereo audio jack with 3-pole captive screw connector

• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)

Install the wallplate directly into the wall using the supplied mud ring or a UL-approved 1-gang

junction box (not supplied). Follow the steps in the “Installation” section on page 2.

Planning - Check the Proposed Installation Location

Before starting the installation it is important that you do the following:

CAUTION:

• Failure to check the items listed below may result in personal injury.

• La non-vérication des éléments listés ci-dessous peut provoquer des blessures.

ATTENTION: Failure to check the items listed below may result in property damage.

Ensure there are no utility cables or pipes at the intended location that might be damaged

or cause injury when you are installing the device.

Check that the installation meets the local and state regulatory requirements, including

building, electrical, and safety codes, and UL and ADA accessibility requirements.

Side View

WPD 110 A WPD 120 A WPD 130 A

DVI

DISPLAYPORT

ABC

WPD 140 A

COMPUTER

ABC

WPD Series Wallplates • Installation Guide (Continued)

During installation ensure the space behind the device

is sufficient for the bend radius of the pigtail. The

recommended minimum bend radii are as follows:

• WPD 110A = 2.0 inches.

• WPD 120A, WPD 130A and WPD 140A = 2.4 inches.

(see image at right)

Installation

1. Using the supplied mud ring or a junction box

(not included) as a guide, mark and cut out the

appropriate material within the marked area.

2. Either:

• Insert the mud ring into the opening, rotate the

locking arms, and secure it with the supplied

screws (as shown at right), or

• Insert the junction box and secure it with nails or

screws.

3. Run the cables (video, audio, IR or RS-232 control)

from the output or input device locations (as

applicable), behind the wall, and to the WPD

location, then thread the cables through the mud

ring or junction box.

4. Video — Insert the HDMI, DisplayPort, DVI, or VGA cable connector into the connector on

the pigtail.

NOTE: If using a DVI display with the WPD 110A, connect a HDMIM-DVIDF adapter and a

separate audio cable.

5. Audio — Secure the output audio cable into the 3-pole captive screw

connector. Wire as described below (see the gure at right). This may

be easier to do before attaching the device to the mud ring.

• For balanced mono audio:

tip (T) = +, ring (R) = -, sleeve (S) = ground

• For unbalanced stereo audio:

tip (T) = left channel, ring (R) = right channel, sleeve (S) = ground

6. Control — 3-pole pass-through connector — Connect applicable cables to the 3-pole

captive screw connector on the rear of the WPD for pass-through signals, such as IR or

RS-232. When connecting the cables, ensure the polarity will be the same as the proposed

input device to avoid crossover and grounding issues.

7. Mount the cabled device into either the mud ring or the junction box and attach the

supplied decorator-style frame.

8. Connect the appropriate input or output devices to the front panel connectors.

9. Test the system and resolve any cabling or signal issues.

Extron

WPD 110 A

Wall Mounting

Bracket

HDMI

ABC

Decorator-Style

Frame

68-2279-01

Rev. C 04 17

WPD 130 A

4.1"

(104 mm)

2.37"

(60 mm)

1.41"

(36 mm)

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron Asia

+65.6383.4400

Extron China

+86.21.3760.1568)

Extron Australia

+61.8.8113.6800

Extron Europe

+31.33.453.4040

Extron Japan

+81.3.3511.7655

Extron Middle East

+971.4.299.1800

Extron India

+91.80.3055.3777

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Accessoires

Extron electronics

Extron electronics OCS 100W Manuel utilisateur

Extron electronics

Extron electronics AXI 22 AT D Manuel utilisateur

Extron electronics

Extron electronics AXI 22 AT D Manuel utilisateur

Extron electronics

Extron electronics RWM 2 Manuel utilisateur

Extron electronics

Extron electronics Extender AKM UK AAP Manuel utilisateur

Extron electronics

Extron electronics PVT SW HDMI RGB D Manuel utilisateur

Extron electronics

Extron electronics Universal Video Interface with Audio RGB 201... Manuel utilisateur

Extron electronics

Extron electronics OCS 100W Manuel utilisateur

Extron electronics

Extron electronics AXI 02 AT Manuel utilisateur

Extron electronics

Extron electronics Architectural Adapter Plate AAP 301 Manuel utilisateur

Extron electronics

Extron electronics Power Sensor Manuel utilisateur

Extron electronics

Extron electronics AXI 02 AT Manuel utilisateur

Extron electronics

Extron electronics OCS 100C Manuel utilisateur

Extron electronics

Extron electronics OCS 100W Manuel utilisateur

Extron electronics

Extron electronics RGB 203 Rxi VTG Manuel utilisateur

Extron electronics

Extron electronics OCS 100C Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur